• The Journal of Korean Academy of Prosthodontics
• /
• v.36 no.6
• /
• pp.858-866
• /
• 1998

Soldering is the usual method used to correct an unstable fixed partial denture framework at patient's try-in; However, presoldering base metal alloys is technique-sensitve and results are unstable because it is difficult to maintain uniform heat distribution and to prevent oxidation of an alloy. A cast-joining technique has been developed by Weiss and Munyon for repair, correction and addition to base metal framework. This joining technique eliminates the problem with presoldering of non-precious frameworks. The object of this study was to 1) compare the relative flexure strength and the joining effectiveness of Ni-Cr-Be cast in two pieces and 'pre-soldered' versus in two pieces and 'cast-joined'. 2) determine the effect of increasing the number of retentive grooves on the face of the cast and 3) determine the effect of the relative matched position of groove patterns on flexure strength. The joining effectiveness can be expressed by the ratio of the mean flexure stress of soldered or cast-joined specimens to that of one-piece cast. Resin rods 3mm in diameter were used as pattern of specimens for one-piece casted, presoldered, and cast-joined groups. Cast-joined specimens had two different patterns of retentive grooves on the joined faces. Type A had cross-shaped grooves 1mm in depth. 0.6mm in width. Type B was the same except for the addition of one more retentive groove. In the experiment connecting cast-joined specimens, half of specimens with type A pattern had their patterns on the faces of paired casts matched with each other as mirror image. With the rest pairs, it was proceeded that one of paired casts turned 45 degrees so that the patterns crossed. Half of specimens with type B pattern also had the patterns matched as mirror image; However, here, one of paired casts turned 90 degrees with the other pairs. Retentive groove in this study lacked the intentional undercuts, in contrast with the suggestion of Weiss and Munyon. The specimens were subjected to four-point flexural loading in an Instron testing machine. The midspan flexural stress was calculated at the point of initial plastic strain as determined from a strip-chart recorder or at the point of failure if this occured at a lower stress level. Within the scope of this study, the following results were obtained. 1. The presoldered group showed flexural strength at least 2 times higher than the cast-joined groups. Its joining effectiveness was 82%. 2. In cast-joined groups, the flexural strength of joints with type B patterns exhibited 1.5 times that of joints with type A patterns. Joining effectivenesses were 38% for type B patterns, 25-26% for type A patterns. 3. The relative matched position of groove patterns did not have any significant effect on flexural strength of the cast-joined specimens with either type A patterns or type B patterns(p>.05).

• Proceedings of the Korea Information Processing Society Conference
• /
• 2006.05a
• /
• pp.1291-1294
• /
• 2006

우리는 P2P 네트워크 환경하에서 멀티캐스팅 스트리밍 전송방법으로서 포워딩 스트림 (forwarding stream)전송 방법을 사용한다. 일명 포워드캐스트(forwardcast)는 P2P 네트워크 환경과 멀티캐스팅 전송에 바탕을 두고, 클라이언트들의 자원을 효율적으로 이용함으로서 초기 클라이언트의 요청 기각률을 낮출 수 있었다. 본 연구에서는 이를 다수의 컨텐츠 서버 환경에 적용시킴으로서 하나의 서버에 집중되는 부하를 분산시킴과 동시에 초기 클라이언트의 기각률을 보다 낮추고자 한다. 실험결과 그 성능을 확인할 수 있었다.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.9 no.3
• /
• pp.1035-1056
• /
• 2015

The efficiency of live Peer-to-Peer (P2P) streaming protocols depends on the appropriateness and the management abilities of their underlying overlay multicast. While a tree overlay structure confines transmission delays efficiently by maintaining deterministic delivery paths, an overlay mesh structure provides adequate resiliency to peers dynamics and easy maintenance. On the other hand, content freshness, playback fluidity and streaming continuity are still challenging issues that require viable solutions. In this paper, we propose a Hybrid Live P2P Streaming Protocol (HLPSP) based on a hybrid overlay multicast that integrates the efficiency of both the tree and mesh structures. Extensive simulations using OMNET++ are conducted to investigate the efficiency of HLPSP in terms of relevant performance metrics, and position HLPSP with respect to DenaCast the enhanced version of the well-known CoolStreaming protocol. Simulation results show that HLPSP outperforms DenaCast in terms of startup delay, end-to-end delay, play-back delay and data loss.

• The Journal of Advanced Prosthodontics
• /
• v.2 no.4
• /
• pp.128-133
• /
• 2010

PURPOSE. The purpose of this study was to compare the accuracy of the implant master cast according to the type (pick-up, transfer) and the length (long, short) of the impression copings. MATERIALS AND METHODS. The metal master cast was fabricated with three internal connection type implant analogs (Osstem GS III analog), embedded parallel and with $10^{\circ}$ of mesial angulation to the center analog. Four types of impression coping were prepared with different combinations of types (transfer, pick-up) and lengths (long, short) of the coping. The impressions were made using vinyl polysiloxane (one step, heavy + light body) with an individual tray, and 10 impressions were made for each group. Eventually, 40 experimental casts were produced. Then, the difference in the distance between the master cast and the experimental cast were measured, and the error rate was determined. The analysis of variance was performed using the SPSS (v 12.0) program (${\alpha}$= .05), and the statistical significance was set at P < .05. RESULTS. The ANOVA showed that the pick-up type impression coping exhibited a significantly lower error rate than the transfer type. However, no significant difference was observed with respect to the length of the impression coping. Additionally, no significant difference was observed between the parallel and mesial angulated groups. CONCLUSION. Within the limitations of this study, the pick-up type impression coping exhibited a more accurate implant master cast than the transfer type in parallel group. The accuracy of the implant master cast did not differ for different lengths of impression coping of at least 11 mm. Additionally, the accuracy of the implant cast was not different for the parallel and $10^{\circ}$ mesial angulated groups.

• Biomedical Science Letters
• /
• v.15 no.1
• /
• pp.47-53
• /
• 2009

Urinary bladder cancer is diagnosed through urine cytology and cytoscopy with biopsy. An atypical urothelial cast is often found by voided urine cytology in a papillary urothelial cell carcinoma. The objective of this study is to demonstrate the significance of the evaluation of urinary nuclear matrix protein (NMP22) level and Sure Path Liquid-based cytology (SP-LBC) as compared to the examination of atypical urothelial cast in voided urine sediment for monitoring bladder cancer. From October 2007 to January 2008, we observed 3240 patients who visited the emergency laboratory of urology of Soonchunhyang University, Cheonan Hospital. Both NMP22 measurement and SP-LBC were performed in 31 patients who were positive in an atypical urothelial cast test. In particular, 26 men and 5 women were found to be atypical urothelial cast-positive persons. The average age for both men and women is 61.8. NMP22 test is positive in 23 of 31 cases (74.2%) from patients with atypical urothelial cast, while the test is negative in 8 of 31 cases (25.8%). The percentages of negativity, atypicality, suspicious malignancy, and malignancy in SP-LBC are 25.8% (8/31), 58.1% (18/31), 9.7% (3/31), and 6.5% (2/31), respectively. The relation of NMP22 positivity with the malignant degree in LBC is significant (P<0.01). Two malignant patients resulting from SP-LBC show the same results in histological examination. Overall, the study suggests the usefulness of NMP22 measurement and LBC as well as the examination of atypical urothelial cast for the diagnosis of early bladder cancer.

• Journal of Welding and Joining
• /
• v.32 no.3
• /
• pp.95-101
• /
• 2014

Joining of grey cast iron by fusion welding has much difficulties for its extremely low ductility and low toughness because of the flake form of the graphite. And the brittle microstructure, i.e. ledeburite may be formed during fusion welding by its rapid cooling rates. By these kinds of welding problem, preheat and post heat treatment temperature must be increased to avoid weld crack or welding problems. In order to avoid these fusion welding problem, friction welding of cast iron was carried out for improving joint soundness, establishing friction welding variables. There is no factor for evaluating friction weldability in continuous drive type friction welding. In this point of view, this study proposed the parameters for calculating friction weld heat input. The results obtained are as follows ; 1. There was a close relationship between tensile strength and flash appearance of friction welded joint. 2. Tensile strength was decreased and flash was severely oxidized as increasing frictional heating time. 3. As increased forging pressure $P_2$, flash had a large crack and tensile strength was decreased. 4. As powdered graphite by rotational frictional force induced flat surface and hindered plastic flow of metal, tensile strength of welded joint was decreased. 5. Heat input for continuous drive type friction welding could be calculated by the factors of $P_1$, $P_2$ and upset distance(${\delta}$).

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.10 no.6
• /
• pp.807-813
• /
• 1986

The orthogonal cutting method of the nodular graphite cast iron in the lathe turning, whose matrix were formulated under two kinds of annealing conditions, has been experimentally studied and the results investigated. The various characteristics of machinabilities of the nodular cast iron, depending upon its matrix, have been obtained from the results as follows. (1) As depth of cut increases, the cutting ratio and the shear angles tend to slightly increase, and as the containing quantity of ferrite matrix increases, they slightly decrease. (2) As depth of cut increases, the cutting force increases in an approximate straight line, and as the containing quantity of ferrite matrix increases, they decreases and the decreasing rate is about 20-30%. (3) As the containing quantity of ferrite matrix increases, the friction force acting on the tool face decreases and the decreasing rate is about 34-40% in case of the lower depth of cut, but in case of the higher depth of cut the decreasing rate is very small. (4) Both shearing force and vertical force show a lineal increases, and according as ferrite matrix increases there is a decrease by 25% in shearing force and a 12-25% decrease in vertical force. (5) Shearing speed and chip flow speed keep almost a constant value irrespective of matrix.

• The Journal of Korean Academy of Prosthodontics
• /
• v.37 no.4
• /
• pp.465-473
• /
• 1999

Bond strength of luting cements to dentin is a critical consideration for success of complete cast crowns. This study was performed to evaluate the relationship between surface characteristics of teeth prepared for complete cast crowns and retention of cemented restorations. Eighty artificial crowns were cast for standardized complete crown tooth preparations accomplished with the use of a special device on recently extracted human teeth. Coarse diamond(#102R, Shofu) and superfine finishing diamond(#SF102R, Shofu) burs of similar shape were used. Crowns in each group were randomly subdivided into few subgroups of 10 for luting cements selected for this study: zinc phosphate cement (FLECK' S), polycarboxylate cement (Poly-F), rein-forced glass ionomer cement (Fuji PLUS). and adhesive resin cement (Panavia 21). Retention was evaluated by measuring the tensile load required to dislodge the artificial crown from tooth preparations with an Instron testing machine, and analysed by one-way ANOVA and Student's t-test. The obtained results were as follows ; 1. When tooth preparation was done with coarse diamond bur, retentive force was diminished in order of Panavia 21 Fuji PLUS, FLECK'S, and Poly-F. Retentive forces showed the significant difference between Fuji PLUS group and FLECK'S group(p<0.001). 2. When tooth preparation was done with superfine diamond bur, retentive force was diminished in order of Fuji PLUS, Panavia 21, FLECK'S, and Poly-F. Retentive forces showed the significant difference between Panavia 21 group and FLECK'S group(p<0.001). 3. Retentive force in coarse tooth surfaces was significantly higher than that in superfine tooth surface with all luting cements(p<0.001), and cement residues were almost retained with-in the cast crown in all groups.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.19 no.4
• /
• pp.269-279
• /
• 2003

This study investigated the mechanical properties of precious metal-ceramic alloy joined by the laser-welding and the soldering compared with the parent metal. Twenty-four tensile specimens were cast in precious metal-ceramic alloy and divided into three groups of eight. All specimens in the control group(group 1) were left in the as-cast condition. Group 2 and 3 were the test specimens, which were sectioned at the center. Eight of sectioned specimens were joined by soldering with a propane-oxygen torch, and the remaining specimens were joined by laser-welding. After joining, each joint diameter was measured, and then tested to tensile failure on an Instron machine. Failure loads were recorded, and then fracture stress(ultimate tensile strength), 0.2% yield strength and % elongation calculated. These data for three groups were subjected to a one-way analysis of variance(ANOVA). Neuman-Keuls post hoc test was then used to determine any significant differences between groups. The fracture locations, fracture surfaces were examined by SEM(scanning electron microscope). The results were as follows: 1) The tensile strength and 0.2% yield strength of the soldered group($280.28{\pm}49.35MPa$, $160.24{\pm}26.67MPa$) were significantly less than both the as-cast group($410.99{\pm}13.07MPa$, $217.82{\pm}17.99MPa$) and the laser-welded group($383.56{\pm}59.08MPa$, $217.18{\pm}12.96MPa$). 2) The tensile strength and 0.2% yield strength of the laser-welded group were about each 98%, 99.7% of the as-cast group. There were no statistically significant differences in these two groups(p<0.05). 3) The percentage elongations of the soldered group($3.94{\pm}2.32%$) and the laser-welded group($5.06{\pm}1.08%$) were significantly less than the as-cast group($14.25{\pm}4.05%$) (p<0.05). 4) The fracture of the soldered specimens occurred in the solder material and many porosities were showed at the fracture site. 5) The fracture of the laser-welded specimens occurred also in the welding area, and lack of fusion and a large void was observed at the center of the fracture surface. However, the laser-welded specimens showed a ductile failure mode like the as- cast specimens. The results of this study indicated that the tensile strengths of the laser-welded joints were comparable to those of the as-cast joints and superior to those of the soldered joints.

• Journal of the Korean Orthopaedic Association
• /
• v.56 no.3
• /
• pp.215-223
• /
• 2021

Purpose: Distal radius fractures in youth are treated conservatively in most cases, but there are some cases of redisplacement in the follow-up period after cast immobilization, even after complete reduction. This study examined the risk factors of redisplacement in reduced unstable distal radius fractures. Materials and Methods: From February 2011 to June 2018, 44 unstable distal radius fractures were managed with a closed reduction and cast immobilization. The patients were aged between 6 and 14 years. The cases of redisplacement were analyzed with the fracture characteristics (fracture obliquity, fracture level ratio, ulnar fracture combined), cast qualities (gap index, cast index, 3 point index, and radius-2nd metacarpal angle) and host factors (age, sex). Results: The mean angulation in the union was 9.2° (0°-32.8°). In the categorical grouping 29 cases were within 10° angulation, and 15 cases were more than 10°. No significant differences in the factors of the cast indices or host factors were noted. The meaningful factor was the fracture level calculated by the relative width of the fracture site divided by the sum of width of diaphysis and epiphysis (p=0.001) and combined ulnar fracture (p=0.019). Conclusion: Unstable distal radius fractures should be treated with more stubborn guidelines lest the fracture loses its anatomical alignment. In particular, in patients with less remodeling power, operative treatment would secure a better result if the fracture occurs in a more proximal location.