• 상하수도학회지
• /
• 제18권4호
• /
• pp.508-514
• /
• 2004

Industrial and municipal wastewater treatment plants produce large amounts of sludge cakes for final disposal. This problem is an inevitable drawback inherent to the activated sludge process. Both the reduction of the amount of sludge produced and improvement of its dewaterability are presently very important issue also in Korea. So many pre-treatment processes have been developed in order to improve sludge dewatering efficiency. In this study the effects of hydrogen peroxide and paper sludge mixing processes were considered as reasonable alternatives to enhance sludge dewaterability. The CST of sludge was significantly decreased, and dewaterability improved by hydrogen peroxide oxidation treatment. The optimum dosage of hydrogen peroxide was proved to be 10mg/g-TS (when TS of sludge was 2%) with the conditions of pH 4 and only 1~2 minutes of reaction time. The mixing of paper sludge with sewage sludge was turned out to be very effective in reduction of sludge cake; 30% of sludge cake reduction was accomplished. Optimum mixing ratio of paper sludge was about 30%(v/v). This process also could save 25% of polymer to be required. These two alternatives are somewhat realistic, but it was concluded that paper sludge mixing process will be the best choice.

• 한국주조공학회지
• /
• 제22권1호
• /
• pp.42-48
• /
• 2002

Effects of coating treatment of metallic Cu, Ni-P film on $SiC_p$, for $SiC_p$/iron aluminide composites were studied. Porous hybrid preforms were fabricated by reactive sintering after mixing the coated $SiC_p$, Fe and Al powders. Then the final composites were manufactured by squeeze casting after pouring AC4C Al alloy melts in preforms. The change of reactive temperature, density, microstructure of the preforms and microstructure of the composites were investigated. The exprimental results were summarized as follows. The thickness of Cu and Ni-P metallic layer formed on $SiC_p$ by electroless plating method were about $0.5{\mu}m$ and coated uniformly. There was no remakable change in the ignition temperature with variation of the mixing ratio of Fe and Al powder while in the case of coated $SiC_p$ it was lower about $20^{\circ}C$ than in the non-coated $SiC_p$. The maximum reaction temperature increased with increasing Al contents, but decreased with increasing $SiC_p$ contents. Expansion ratio of preform after reactive sintering increased with amount of Cu coated $SiC_p$. In the case of Fe-70at.%Al, the expansion ratio was about 7% up to 8wt.% of $SiC_p$, addition but further addition of $SiC_p$, increased the ratio significantly. And in the case of Fe-50 and 60at.%Al, it was about 20% up to 16wt.% of $SiC_p$ addition and about 28% in 24wt.% of $SiC_p$, addition. The microstructures of compounds showed that the grains became finer as amount of $SiC_p$, and mixing ratio of iron powder increased and the shape of compounds was changed gradually from irregular to spheroidal.

• 대한환경공학회지
• /
• 제35권11호
• /
• pp.803-808
• /
• 2013

본 연구의 목적은 칼슘염을 함유한 레미콘 슬러지를 이용하여 불소함유폐수를 물에 난용성인 $CaF_2$ 화합물 형태로 침전시켜 처리하는데 있어 pH, 레미콘슬러지 주입량, Seed물질 주입량, 교반속도, 교반시간의 최적 조건을 도출하고자 하는데 있다. 실험결과 레미콘 슬러지를 이용한 대상폐수의 $CaF_2$ 침전 반응에서 함수율 및 불소의 제거효율 등을 고려할 경우 최적의 pH 6, 레미콘 슬러지 주입량은 10 g/L, Seed 물질 주입량은 2 g/L, 교반속도은 100 rpm, 교반시간은 60 min으로 관찰되었다. 이 때 Seed 물질의 주입은 불소제거효율에는 영향이 없는 것으로 나타났지만 침전물의 형성이 되는 반응을 촉진시키고 플럭형성을 원활하게 하여 고액 분리가 잘 되어 함수율이 낮아지는 결과가 나타났다.

• Nuclear Engineering and Technology
• /
• 제54권6호
• /
• pp.2311-2320
• /
• 2022

The main outcomes of the experiments H2P6 performed in the thermal-hydraulics large-scale PANDA facility at PSI in the frame of the OECD/NEA HYMERES-2 project are presented in this article. The experiments of the H2P6 series consists of two PANDA tests characterized by the activation of three (H2P6_1) or one (H2P6_2) cooler(s) in an initially stratified and pressurized containment atmosphere. The initial stratification is defined by a helium-rich region located in the upper part of the vessel and a steam/air atmosphere in the lower part. The activation of the cooler(s) results i) in the condensation of the steam in the vicinity of the cooler(s), ii) the corresponding activation of large scale natural circulation currents in the vessel atmosphere, with the result of iii) the re-distribution and mixing of the Helium stratification initially located in the upper half of the vessel and iv) the continuous pressure decay. The initial helium layer represents hydrogen generated in a postulated severe accident. The main question to be answered by the experiments is whether or not the interaction of the different, localized cooler units would be important for the application of numerical methods. The paper describes the initial and boundary conditions and the experimental results of the H2P6 series with the suggestion of simple scaling laws for both experiments in terms of i) the temperature difference(s) across the cooler(s), ii) the transient steam and helium content and iii) the pressure decay in the vessel. The outcomes of this scaling indicate that the interaction between separate, closely localized units does not play a prominent role for the present experiments. It is therefore reasonable to model several units as one large component with equivalent heat transfer area and total water flow rate.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제44회 동계 정기학술대회 초록집
• /
• pp.483-483
• /
• 2013

Latral Composition Modulation (LCM)으로 성장한 InP/GaP 초격자(Superlattice)의 선편광된 광발광(Photoluminescence) 특성을 저온(5 K)에서 측정하였다. LCM 기법은 z-축 방향으로 InP와 GaP를 단층 초격자(monolayer supperlattice)로 성장하는 과정에서 strain에 의해 x-y 평면으로 초격자가 형성되는 특별한 경우이다. 이렇게 성장된 LCM 초격자의 경우 In-rich 영역과 Ga-rich 영역이 교차로 성장되는 구조를 가지며 가전자대역(valence band)에서 무거운 양공과 가벼운 양공의 band mixing 이 일어나게 되어 선평광된 발광특성을 가진다. 우리는 저온 발광실험에서 In-rich 영역과 Ga-rich 영역의 재결합에 의해 나타나는 두 개의 독립된 전이 피크를 측정하였다. 이 두 피크는 [110] 방향의 편광에서 발광 강도가 최대치를 가지며 [1-10] 방향에서 최소값을 가짐을 보였다. 이때 전이 에너지의 경우 [110] 방향에서 [1-10] 방향으로 편광이 바뀔 때 Ga-rich 영역의 전이의 경우 적색편이를 나타낸 반면 In-rich 영역의 경우 청색편이를 보이는 현상을 발견하였다. 이러한 상반된 편이 현상은 서로 다른 3족 물질의 영역에 따라 격자 상수가 바뀌며 tensile strss와 compressive stress에 따른 가전자 대역의 band mixing 변화에 기인하는 것으로 여겨진다.

• 한국세라믹학회지
• /
• 제30권10호
• /
• pp.829-837
• /
• 1993

Chemically and geometrically homogeneous mixing of Si3N4 powders with sintering additives(YAG, 3Y2O3$.$5Al2O3) was attempted via coprecipitation method. X-ray dot maps for the additive elements(Al and Y) showed that the additives are evenly distributed in the powder mixture prepared by coprecipitation method(CP). TEM observation of the coprecipittion-treated Si3N4 powders revealed that they are covered with extremely fine crystallites of additive. The shift in isoelectric point(IEP) of Si3N4 powders from pH 6.7 to pH 7.9 after coprecipitation mixing gave another evidence for coating of Si3N4 powders with YAG additives. SIMS analysis for composition on the surface and in the matrix of mixed powders showed that the YAG additives are highly enriched on the surface of coprecipitation-treated Si3N4 powders. Especially when a small amount of additive was used, the effect of homogeneous additive distribution on densification was preceptible: After pressureless-sintering of powder compacts containing 5 mol% YAG at 1800$^{\circ}C$ for 0.5h, a sintered density of 96.5% theoretical was obtained from the specimens prepared bycoprecipitation in comparison with 93.8% from the mechanically-mixed one.

• Journal of the Korean Statistical Society
• /
• 제22권2호
• /
• pp.259-269
• /
• 1993

A moving average model, LMA(q) and an autoregressive-moving average model, NLARMA(p, q), with Laplacian marginal distribution are constructed and their properties are discussed; Their autocorrelation structures are completely analogus to those of Gaussian process and they are partially time reversible in the third order moments. Finally, we study the mixing property of NLARMA process.

• 대한수학회논문집
• /
• 제16권2호
• /
• pp.163-204
• /
• 2001

먼저 Erdos-Renyi의 새로운 강대수 법칙을 소개하고, 여러 가지 형태로 발전된 Erdos-Renyi 형의 법칙과 그 응용을 보여준다. 보다 더 일반적인 Erdos-Renyi형의 법칙과 그 응용을 보여준다. 보다 더 일반적인 Erdos-Renyi 형 법칙을 찾기 위해 Csorgo-Revesz 증분형태의 극한정리들을 소개하여 종속 mixing 조건이 주어진 정상 Gauss 확률변수들의 부분합에 대해 Csorgo-Revesz 증분형태의 새로운 극한정리들을 얻는다. 끝으로, 유한차원 벡터공간, ι(sup)p-공간, ι(sup)$\infty$-공간에서 각각 값을 갖는, 연속 Gauss 과정에 대해서 필자에 의해 최근에 발표된 몇 편의 논문을 소개한다.

• 센서학회지
• /
• 제20권6호
• /
• pp.368-374
• /
• 2011

A microfluidic device for real-time monitoring of residual free chlorine and pH in water based on optical absorption is proposed. The device consists of a serpentine micromixer for mixing samples with a reagent, and a photodiode and light emitting diode(LED) for the detection of light absorbance at specific wavelengths, determined for specific reagent combinations. Spectral analyses of the samples mixed with N, N'-diethyl-p-phenylenediamine(DPD) reagent for chlorine determination and bromothymol blue(BTB) for pH measurement are performed, and the wavelengths providing the most useful linear changes in absorbance with chlorine concentration and pH are determined and used to select the combination of LED and photodiode wavelengths for each analyte. In tests using standard solutions, the device is shown to give highly reproducible results, demonstrating the feasibility of the device for the inexpensive and continuous monitoring of water quality parameters with very low reagent consumption.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.2
• /
• pp.693-696
• /
• 2004

For InGaP/GaAs HBT applications, we have developed characterized MIM capacitors with thin $1000{\AA}$ PECVD silicon nitride which were deposited with $SiH_4/NH_3$ gas mixing rate, working pressure, and RF power of PECVD at $300^{\circ}C$ and had the capacitance density of 600 pF/$mm^2$ with the breakdown electric fields of 3073 MV/cm. Three PECVD process parameters were designed to lower the refractive index and then lower the deposition rate of silicon nitride films for the high breakdown electric field. At the PECVD process condition of gas mixing rate (0.92), working pressure (1.3 Torr), RF power (53 W), the AFM Rms value of about $1000{\AA}$ silicon nitride on the bottom metal was the lowest of 0.662 nmand breakdown electric fields were the highest of about 73 MV/cm.