• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.266.2-266.2
• /
• 2016

최근 디스플레이 산업의 확대에 따라 투명 전도 산화물(Transparent Conducting Oxides:TCOs)의 수요가 급증하고 있다. 이 중 ZnO는 wide bandgap (3.37eV)와 large exciton binding energy (60meV)의 값을 가져 차세대 투명 전도 산화물, LED와 LD 등의 소자 소재로 각광받고 있다. ZnO는 electron을 내어놓는 native defect 때문에 기본적으로 n-type 물성을 띈다. 그래서 dopant를 이용해 p-type ZnO를 제작할 때 native defect를 줄이는 것이 중요한 요점이 된다. 이 때 buffer layer를 사용하여 native defect를 줄이는 방법이 사용되고 있다. 본연구에서는 RF-magnetron sputtering법을 이용하여 c-plane sapphire 기판 위에 다양한 조건의 ZnO buffer layer를 증착하고, 그 위에 ZnO:(Al,P) co-doping한 APZO를 증착하였다. ZnO buffer layer 증착조건의 변수는 증착온도와 Ar:O2의 비율을 변수로 두었다. 이러한 박막을 FE-SEM, XRD, Hall effect measurement, AFM을 통하여 미세구조와 물성을 관찰하였다. 이 때 APZO보다 낮은 증착온도에서 ZnO buffer layer가 증착되면 APZO를 증착하는 동안 chamber 내부에서 열처리하는 효과를 얻게 되고, UHV(Ultra High Vaccum)에서 열처리 될 때 ZnO buffer layer의 mophology와 결정성이 변하게 되는 모습을 관찰아혔다. 또한 본 실험을 통해 ZnO buffer layer의 증착 온도가 APZO의 증착온도보다 높을 때 제어 가능한 실험이 됨을 확인 할 수 있었다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.94-94
• /
• 2008

We have performed simulation for Junction Field Effect Transistor(JFET) using Silvco to improve its electrical properties. The device structure and process conditions of Si-control JFET(Si-JFET) were determined to set its cut off voltage and drain current(at Vg=0V) to -0.5V and $300{\mu}A$, respectively. From electrical property obtained at various implantation energy, dose, and drive-in conditions of p-gate doping, we found that the drive in time of p-type gate was the most determinant factor due to severe diffusion. Therefore we newly designed SiGe-JFET, in which SiGe layer is to epitaxial layers placed above and underneath of the Si-channel. The presence of SiGe layer lessen the p-type dopants (Boron) into the n-type Si channel the phenomenon would be able to enhance the structural consistency of p-n-p junction. The influence of SiGe layer will be discussed in conjunction with boron diffusion and corresponding I-V characteristics in comparison with Si-control JFET.

• 전기전자학회논문지
• /
• 제17권2호
• /
• pp.182-188
• /
• 2013

Using a ceramic target ZnO:In with In doping concentration of 2%, hetero-junctions of n-ZnO:In/p-Si and p-ZnO:(In, N)/n-Si were fabricated by depositing Indium doped n - type ZnO (ZnO:In or IZO) and Indium-nitrogen co-doped p - type ZnO (ZnO:(In, N)) films on wafers of p-Si (100) and n-Si (100) by DC magnetron sputtering, respectively. These films with the best electrical and optical properties were then obtained. The micro-structural, optical and electrical properties of the n-type and p-type semiconductor thinfilms were characterized by X-ray diffraction (XRD), RBS, UV-vis; four-point probe resistance and room-temperature Hall effect measurements, respectively. Typical rectifying behaviors of p-n junction were observed by the current-voltage (I-V) measurement. It shows fairly good rectifying behavior with the fact that the ideality factor and the saturation current of diode are n=11.5, Is=1.5108.10-7 (A) for n-ZnO:In/p-Si hetero-jucntion; n=10.14, Is=3.2689.10-5 (A) for p-ZnO:(In, N)/n-Si, respectively. These results demonstrated the formation of a diode between n-type thin film and p-Si, as well as between p-type thin film and n-Si..

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2009년도 춘계학술발표대회
• /
• pp.29.1-29.1
• /
• 2009

Fabrication of good quality P-type GaN remained as a challenge for many years which hindered the III-V nitrides from yielding visible light emitting devices. Firstly Amano et al succeeded in obtaining P-type GaN films using Mg doping and post Low Energy Electron Beam Irradiation (LEEBI) treatment. However only few region of the P-GaN was activated by LEEBI treatment. Later Nakamura et al succeeded in producing good quality P-GaN by thermal annealing method in which the as deposited P-GaN samples were annealed in N2 ambient at temperatures above $600^{\circ}C$. The carrier concentration of N type and P-type GaN differs by one order which have a major effect in AlGaN based deep UV-LED fabrication. So increasing the P-type GaN concentration becomes necessary. In this study we have proposed a novel method of activating P-type GaN by electrochemical potentiostatic method. Hydrogen bond in the Mg-H complexes of the P-type GaN is removed by electrochemical reaction using KOH solution as an electrolyte solution. Full structure LED sample grown by MOCVD serves as anode and platinum electrode serves as cathode. Experiments are performed by varying KOH concentration, process time and applied voltage. Secondary Ion Mass Spectroscopy (SIMS) analysis is performed to determine the hydrogen concentration in the P-GaN sample activated by annealing and electrochemical method. Results suggest that the hydrogen concentration is lesser in P-GaN sample activated by electrochemical method than conventional annealing method. The output power of the LED is also enhanced for full structure samples with electrochemical activated P-GaN. Thus we propose an efficient method for P-GaN activation by electrochemical reaction. 30% improvement in light output is obtained by electrochemical activation method.

• 한국진공학회지
• /
• 제20권2호
• /
• pp.135-140
• /
• 2011

Be을 도핑한 p형 GaSb:Be 에피층의 광여기 발광(PL) 스펙트럼(20 K)의 도핑밀도에 따른 변화를 조사하여, Be 억셉터의 근원을 분석하였다. 도핑을 증가시키면 PL 피크가 고에너지로 변위하고 반치폭은 줄어드는 경향을 보이다가, 밀도가 ${\sim}10^{17}cm^{-3}$ 이상에서 피크 에너지는 오히려 저에너지로 변위하고 반치폭이 늘어나는 현상을 관측하였다. 3개 피크로 분리한 PL 스펙트럼의 적분 PL 강도 변화를 통하여, 도핑 증가에 따라 $Be[Be_{Ga}]$ 준위(0.794 eV)는 감소하는 반면 진성결함에 기인한 $A[Ga_{Sb}]$ 피크(0.778 eV)와 함께 Be과 A 사이에 위치하는 새로운 $Be^*$ 준위(0.787 eV)가 증가하기 때문으로 분석되었다. 이것은 Be을 도핑한 p-GaSb:Be 에피층에는 Be 얕은준위(${\Delta}E=16meV$)와 Be과 A 결함준위가 결합한 $Be^*[Ga_{Sb}-Be_{Ga}]$의 복합준위(${\Delta}E=23meV$)가 공존하기 때문으로 논의하였으며, ${\sim}10^{17}cm^{-3}$ 이상 도핑할 경우에는 Be 준위가 다소 감소할 수 있음을 보였다.

• 전자공학회논문지A
• /
• 제28A권11호
• /
• pp.887-893
• /
• 1991

To take advantage of Ti-polycide, when it is contacted with both n+ and p+ active area of silicon, the effects of BF$_2$ on the formation of Ti-silicide were investigated with RTA temperature and dopant concentration. The intermediate phase C49 TiSi$_2$ appeared at $650^{\circ}C$ and the stable phase C54 TiSi2 was formed at $700^{\circ}C$. And the formation of Ti-silicide was hindered by BF$_2$ doping and this trend was decreased with increasing temperature. The out-diffusion phenomena of BF$_2$ into Ti silicide were not observed. And significantly, the native oxide was a chief factor preventing the formation of Ti-silicides.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.287.2-287.2
• /
• 2014

PV (photovoltaic) has becoming an important industry to invest due to its high robustness and require very little maintenance which goes a long time. Solar cell fabrication involves a few critical processes such as doping to make the N-type and P-type silicon, contact metallization, surface texturization, and anti-reflection coatings. Anti-reflection coating is a kind of surface passivation which ensures the stability, and efficiency of the solar cell. Thus, I will focus on the changes happen to the solar cell due to the reflectance and anti-reflection coating by PC1D. By using the PC1D (solar cell simulation program), I would analysis the effect of reflectance on the N-type cell. At last I will conclude the result regarding what I learned throughout this experiment.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.197-197
• /
• 2012

Device 제작에 사용된 graphene은 일반적인 lithography 공정에서 resist residue에 의한 오염을 피할 수 없으며 이로 인하여 graphene의 pristine한 성질을 잃어버린다. 본 연구에서는 graphene을 저밀도의 argon inductively coupled plasma (Ar-ICP)를 통해 처리함으로서 graphene based back-gated field effect transistor (G-FET)의 특성변화를 유도한 결과에 대해서 보고한다. Argon capacitively coupled plasma (Ar-CCP)은 에 노출된 graphene은 강한 ion bombardment energy로 인하여 쉽게 planar C-C ${\pi}$ bonding (bonding energy: 2.7 eV)이 breaking되어 graphene의 defect이 발생되었다. 하지만 우리의 경우 저밀도의 Ar-ICP가 적용될 때 graphene의 defect이 제한되며 이와 동시에 contamination 만을 제거할 수 있었다. 소자의 전기적 측정 (Gsd-Vbg)을 통하여 contamination으로 인하여 p-doping된 graphene은 pristine 상태로 회복되었으며 mobility도 회복됨이 확인되었다. Ar-ICP를 이용한 graphene cleaning 방법은 저온공정, 대면적 공정, 고속공정을 모두 만족시키며 thermal annealing, electrical current annealing을 대체하여 graphene 기반 소자를 생산함에 있어 쉽고 빠르게 적용할 수 있는 강점이 있다.

• 약학회지
• /
• 제36권2호
• /
• pp.110-114
• /
• 1992

In order to evaluate the antimicrobial effect of 2, 3-substituted-1, 4-naphthoquinone derivatives, we newly synthesized several 2-chloro, 2-bromo and 2-hydroxy-1, 4-naphthoquinones and subjected to antibacterial and antifungal activities, in vitro, against Escherichia coli NIHJ, Staphylococcus aureus ATCC6538p, Candida albicans 10231, Aspergillus niger 1231 and Tricophyton mentagrophytes 6085. Among these derivatives 3, 9, 18 and 23 showed the potent antibacterial activities. 18, 23 and 28 have the antifungal activities. However, these compounds have no significant hemolytic activity at concentrations higher than that required for showing the antibacterial and antifungal activities.

• 한국재료학회지
• /
• 제33권11호
• /
• pp.491-496
• /
• 2023

As the demand for p-type semiconductors increases, much effort is being put into developing new p-type materials. This demand has led to the development of novel new p-type semiconductors that go beyond existing p-type semiconductors. Copper iodide (CuI) has recently received much attention due to its wide band gap, excellent optical and electrical properties, and low temperature synthesis. However, there are limits to its use as a semiconductor material for thin film transistor devices due to the uncontrolled generation of copper vacancies and excessive hole doping. In this work, p-type CuI semiconductors were fabricated using the chemical vapor deposition (CVD) process for thin-film transistor (TFT) applications. The vacuum process has advantages over conventional solution processes, including conformal coating, large area uniformity, easy thickness control and so on. CuI thin films were fabricated at various deposition temperatures from 150 to 250 ℃ The surface roughness root mean square (RMS) value, which is related to carrier transport, decreases with increasing deposition temperature. Hall effect measurements showed that all fabricated CuI films had p-type behavior and that the Hall mobility decreased with increasing deposition temperature. The CuI TFTs showed no clear on/off because of the high concentration of carriers. By adopting a Zn capping layer, carrier concentrations decreased, leading to clear on and off behavior. Finally, stability tests of the PBS and NBS showed a threshold voltage shift within ±1 V.