• Journal of Magnetics
• /
• 제10권3호
• /
• pp.95-98
• /
• 2005

We report hole-induced ferromagnetism in diluted magnetic semiconductor $Zn_{0.99}Mn_{0.01}$ films grown on $SiO_2/Si$ substrates by reactive sputtering. The p-type conduction with hole concentration over $10^{18}\;cm^{-3}$ is achieved by P doping followed by rapid thermal annealing at $800^{\circ}C$ in a $N_2$ atmosphere. The p-type $Zn_{0.99}Mn_{0.01}O:P$ is carefully examined by x-ray diffraction and transmission electron microscopy. The magnetic measurements for $p-Zn_{0.99}Mn_{0.01}O:P$ clearly reveal ferromagnetic characteristics with a Curie temperature above room temperature, whereas those for $n-Zn_{0.99}Mn_{0.01}O:P$ show paramagnetic behavior. The anomalous Hall effect at room temperature is observed for the p-type film. This result strongly supports hole-induced room temperature ferromagnetism in $p-Zn_{0.99}Mn_{0.01}O:P$.

• 한국산학기술학회논문지
• /
• 제1권2호
• /
• pp.33-40
• /
• 2000

본 연구는 반도체 크린룸에서 VOC(volatile organic compound)과 수분을 제거하기 위한 흡착로타에 관한 것이다. 흡착로타는 세라믹 페이퍼 허니컴 기질에 NaX 제올라이트와 TS-1 제올라이트로 만들어졌다. NaX 제올라이트는 수열합성법으로 합성되어졌으며, NaX 제올라이트 결정(2∼3 ㎛)을 seed로 합성 조성에 3∼5 wt%까지 첨가하여 5 ㎛의 균일한 NaX 제올라이트를 성장시켰다. Seed의 첨가는 seed를 첨가하지 않은 합성용액과 비교하여 결정의 크기가 크며, 균일한 NaX 제올라이트 결정을 성공적으로 합성하였다. TS-1 제올라이트는 초기 반응액의 pH를 변화시켜 합성하였다. 반응물의 pH는 10.0에서 11.5 까지의 범위를 가지며, PH 10.4에서 큰 기공(8∼10 (equation omitted))을 가진 TS-1 제올라이트(ETS-10)가 합성되는 반면 pH가 11.5에서는 작은 기공 (3∼5 (equation omitted))을 갖는 TS-1 제올라이트(ETS-4)가 합성되었다.

• 마이크로전자및패키징학회지
• /
• 제21권1호
• /
• pp.13-17
• /
• 2014

The direct-patternable $SnO_2$ thin film was successfully fabricated by photochemical metal-organic deposition. The composition and chemical bonding state of $SnO_2$ thin film were analyzed by using X-ray photoelectron spectroscopy (XPS) from the surface to the interface with Si substrate. XPS depth profiling analysis allowed the determination of the atomic composition in $SnO_2$ film as a function of depth through the evolution of four elements of C 1s, Si 2p, Sn 3d, and O 1s core level peaks. At the top surface, nearly stoichiometric $SnO_2$ composition (O/Sn ratio is 1.92.) was observed due to surface oxidation but deficiency of oxygen was increased to the interface of patterned $SnO_2/Si$ substrate where the O/Sn ratio was about 1.73~1.75 at the films. This O deficient state of the film may act as an n-type semiconductor and allow $SnO_2$ to be applied as a transparent electrode in optoelectronic applications.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제6권1호
• /
• pp.10-15
• /
• 2006

Various sizes of erbium/platinum silicided n/p-type Schottky barrier metal-oxide-semiconductor field effect transistors (SB-MOSFETs) are manufactured from $20{\mu}m$ to 10nm. The manufactured SB-MOSFETs show excellent DIBL and subthreshold swing characteristics due to the existence of Schottky barrier between source and channel. It is found that the minimization of trap density between silicide and silicon interface and the reduction of the underlap resistance are the key factors for the improvement of short channel characteristics. The manufactured 10 nm n-type SBMOSFET showed $550{\mu}A/um$ saturation current at $V_{GS}-V_T$ = $V_{DS}$ = 2V condition ($T_{ox}$ = 5nm) with excellent short channel characteristics, which is the highest current level compared with reported data.

• 한국산업융합학회 논문집
• /
• 제22권2호
• /
• pp.219-226
• /
• 2019

This paper describes the development of a 500W DC/DC converter for use with a thermoelectric module(TEM). A thermoelectric device is a structure in which a P-type semiconductor and an N-type semiconductor are electrically connected in series and thermally connected in parallel. There is a feature that an electromotive force is generated by making a temperature difference between both surfaces of a thermoelectric element. This feature can be used as a renewable power source without the need for fossil energy. The proposed converter boosts the low generation voltage of the thermoelectric element to secure the voltage for the grid connection. This converter is a combination of a resonant converter for boosting and a boost-converter for output voltage control. This structure has an advantage that a voltage can be stepped up at a high efficiency and precise output voltage control is possible. We carry out simulations and experiments to verify the validity.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제5권2호
• /
• pp.69-76
• /
• 2005

Interface-trap density, lifetime and Schottky barrier height of erbium-silicided Schottky diode are evaluated using equivalent circuit method. The extracted interface trap density, lifetime and Schottky barrier height for hole are determined as $1.5{\times}10^{13} traps/cm^2$, 3.75 ms and 0.76 eV, respectively. The interface traps are efficiently cured by $N_2$ annealing. Based on the diode characteristics, various sizes of erbium- silicided/platinum-silicided n/p-type Schottky barrier metal-oxide-semiconductor field effect transistors (SB-MOSFETs) are manufactured from 20 m to 35nm. The manufactured SB-MOSFETs show excellent drain induced barrier lowering (DIBL) characteristics due to the existence of Schottky barrier between source and channel. DIBL and subthreshold swing characteristics are compatible with the ultimate scaling limit of double gate MOSFETs which shows the possible application of SB-MOSFETs in nanoscale regime.

• 센서학회지
• /
• 제28권1호
• /
• pp.23-29
• /
• 2019

A copper tetracumylphenoxy phthalocyanine (CuPccp) thin film was formed on an organic insulator film by Langmuir-Blodgett (LB) deposition for gas sensor fabrication. To increase the reproducibility of film transfer, stearyl alcohol was used as a transfer promoter. The structural properties of the CuPccp layers were optically monitored through attenuated total reflection and polarization-modulated ellipsometry techniques. The average thickness of a single layer of the CuPccp LB film was measured to be 2.5 nm. Despite the role of the transfer promoter, the stability of the layer transfer was not sufficient to ensure homogeneity of the LB film. This was probably due to the presence of aggregates in the molecular structure of the CuPccp LB film. Nevertheless, copper phthalocyanine polymorphism can be greatly suppressed by the LB arrangement, which appears to contribute to the improvement of electrical conductivity. The p-type semiconductor characteristics were confirmed by Hall measurements from the CuPccp LB films.

• 마이크로전자및패키징학회지
• /
• 제28권4호
• /
• pp.85-89
• /
• 2021

AlGaN 기반 UV-C 발광다이오드(LEDs)에 전기화학적 전위차 활성화(EPA)에 의한 p-형 활성화를 진행하였다. 높은 저항과 낮은 전도도를 유발하는 중성 Mg-H의 복합체의 수소원자를 EPA를 이용하여 제거하여 p-형 활성화 효율을 높였다. 중성 Mg-H 복합체는 주요 매개 변수인 용액, 전압, 시간에 의해 Mg^-과 H⁺로 분해되며, 2차 이온질량 분광법(SIMS) 분석을 통하여 개선된 정공 캐리어의 농도를 확인할 수 있었다. 이 메커니즘은 결국 내부 양자효율(IQE)의 증가, 광 추출 효율 향상, 역 전류 영역의 누설전류 값 개선, 접합 온도 개선 등을 이루어 결과적으로 UV-C LED의 수명을 향상시켰다. 체계적인 분석을 위해 SIMS, Etamax IQE 시스템, 적분구, 전류-전압(I-V) 측정 등을 사용하였으며, 그 결과를 기존의 N₂-열 처리 방법과 비교 평가하였다.

• 한국결정성장학회지
• /
• 제9권6호
• /
• pp.542-546
• /
• 1999

InP single crystal, III-V binary compound semiconductor, was grown by VGF(vertical gradient freeze) method using quartz ampoule and its electrical optical properties were investigated. Phosphorous powders were put in the bottom of quartz ampoule and Indium metal charged in conical quartz crucible what was attached at the upper side position inside the quartz ampoule. It was vacuous under the pressure of $10^5$Torr and sealed up. Indium metal was melted at $1070^{\circ}C$ and InP composition was formed by diffusion of phosphorous sublimated at $450^{\circ}C$ into Indium melt. By cooling the InP composition melt ($2^{\circ}C$~$5^{\circ}C$/hr of cooling rate) in range of $1070^{\circ}C$~$900^{\circ}C$, InP crystal was grown. The grown InP single crystals were investigated by X-ray analysis and polarized optical microscopy. Electrical properties were measured by Van der Pauw method. At the cooling method. At the cooling rate of $2^{\circ}C$/hr, growth direction of ingot was [111] and the quality of ingot was better at the upper side of ingot than the lower side. It was found that the InP crystals were n-type semiconductor and the carrier concentration, electron mobility and relative resistivity were $10^{15}$~$10^{16}/\textrm{cm}^3$ , $2\times 10^3$~$3\times 10^4{\textrm}{cm}^2$/Vsec and$2\times 10^{-1}$~$2\times 10^{-3}$/ Wcm in the range of 150K~300K, respectively.

• 한국결정성장학회:학술대회논문집
• /
• 한국결정성장학회 1999년도 PROCEEDINGS OF 99 INTERNATIONAL CONFERENCE OF THE KACG AND 6TH KOREA·JAPAN EMG SYMPOSIUM (ELECTRONIC MATERIALS GROWTH SYMPOSIUM), HANYANG UNIVERSITY, SEOUL, 06월 09일 JUNE 1999
• /
• pp.419-431
• /
• 1999

InP, III-V binary compound semiconductor, single crystal was grown by VGF (vertical gradient freeze) method using quartz ampoule and its electrical optical properties were investigated. Phosphorous powders were put in the bottom of quartz ampoule and Indium metal changed in conical quartz crucible hat was attached at the upper side position inside the quartz ampoule. It was vacuous under the pressure of 10-5 Torr and sealed up. In metal in the quartz crucible was melted at 1070$^{\circ}C$ and phophorous sublimated at 450$^{\circ}C$, there after it was diffused in In melt and so InP composition was formed. By cooling the InP composition melt (2$^{\circ}C$∼5$^{\circ}C$/hr of cooling rate) in range of 1070$^{\circ}C$∼900$^{\circ}C$, InP crystal was grown. the grown InP single crystals were investigated by X-ray analysis and polarized optical microscopy. Electrical properties of them were measured by Van der Pauw method. At the cooling rate of 2$^{\circ}C$/hr, its direction was (111), quality of the ingot ws better upper side of the ingot than lower. It was found that the InP crystals were n-type semiconductor and the carrier concentration, electron mobility and relative resistivity were 1015∼1016/㎤, 2x103∼3x104$\textrm{cm}^2$/Vsec and 2x10-1∼2x10-3Ωcm in the range of 150K∼300K, respectively.