• 한국재료학회지
• /
• 제28권5호
• /
• pp.273-278
• /
• 2018

Lithium-ion batteries have been considered the most important devices to power mobile or small-sized devices due to their high energy density. $LixCoO_2$ has been studied as a cathode material for the Li-ion battery. However, the limitation of its capacity impedes the development of high capacity cathode materials with Ni, Mn, etc. in them. The substitution of Mn and Ni for Co leads to the formation of solid solution phase $LiNi_xMn_yCo_{1-x-y}O_2$ (NMC, both x and y < 1), which shows better battery performance than unsubstituted $LiCoO_2$. However, despite a high discharge capacity in the Ni-rich compound (Ni > 0.8 in the metal site), poor cycle retention capability still remains to be overcome. In this study, aiming to improve the stability of the physical and chemical bonding, we investigate the stabilization effect of Ca in the Ni-rich layered compound $Li(Ni_{0.83}Co_{0.12}Mn_{0.05})O_2$, and then Ca is added to the modified secondary particles to lower the degree of cationic mixing of the final particles. For the optimization of the final grains added with Ca, the Ca content (x = 0, 2.5, 5.0, 10.0 at.%) versus Li is analyzed.

• Journal of Electrochemical Science and Technology
• /
• 제14권3호
• /
• pp.293-300
• /
• 2023

The global energy storage markets have gravitated to high-energy-density and low cost of lithium-ion batteries (LIBs) as the predominant system for energy storage such as electric vehicles (EVs). High-Ni layered oxides are considered promising next-generation cathode materials for LIBs owing to their significant advantages in terms of high energy density. However, the practical application of high-Ni cathodes remains challenging, because of their structural and surface instability. Although extensive studies have been conducted to mitigate these inherent instabilities, a two-step process involving the synthesis of the cathode and a dry/wet coating is essential. This study evaluates a one-step β-Li₂SnO₃ layer coating on the surface of LiNi_0.8Co_0.2O₂ (NC82) via the thermal segregation of Sn owing to the solubility limit with respect to the synthesis temperature. The doping, segregation, and phase transition of Sn were systematically revealed by structural analyses. Moreover, surface-engineered 5 mol% Sn-coated LiNi_0.8Co_0.2O₂ (NC82_Sn5%) exhibited superior capacity retention compared to bare NC82 owing to the stable surface coating layer. Thus, the developed one-step coating method is suitable for improving the properties of high-Ni layered oxide cathode materials for application in LIBs.

• Journal of Electrochemical Science and Technology
• /
• 제14권3호
• /
• pp.262-271
• /
• 2023

For electrode stability and the electrochemical performance of the Li-ion cell, it is essential that the active ingredients and unique additives in the polymer binder be well dispersed with the solvent-based slurry. The efficient procedure used to create the slurry affects the rheological characteristics of the electrode slurry. When successively adding different steps of Nmethyl-2-pyrrolidone (NMP) solvent to the cathode composition, it is evenly disseminated. The electrochemical performance of the Li-ion cells and the electrodes made with slurry formed by single step and multiple steps of addition of NMP solvent are examined. To preform rheological properties of cathode electrode slurry on Ni-rich Lithium Nickel-Cobalt-Aluminum Oxide (LiNi_0.80Co_0.15Al_0.05) (NCA). Also, we investigate different step addition of electrode formation and mechanical strength characterization like peel strength. According to the EIS study, a multi-step electrode slurry has lower internal resistance than a single-step electrode slurry, which results in better electrical characteristics and efficiency. Further, microstructure of electrodes is obtained electrochemical performance in the 18650 cylindrical cells with targeted capacity of 1.5 Ah. The slurry of electrodes prepared by single step and multiple steps of addition of NMP solvent and its effect on the fabrication of 1.5 Ah cells. A three-step solvent addition on slurry has been found to be a lower internal resistance than a single-step electrode slurry as confirmed by the EIS analysis, yielding improved electrical properties and efficiency.

• 전기화학회지
• /
• 제10권1호
• /
• pp.7-13
• /
• 2007

Glycine Nitrate Process(GNP)를 이용하여 $La_{0.75}Sr_{0.25}FeO_3$를 합성하였다. 이때, GNP의 글리신의 함량은 화학양론식으로 계산하여 3.17mol을 첨가하였다. ICP-AES분석으로 각각의 조성 함량을 조사하고, XRD, SEM분석으로 합성된 분말의 결정성과 입자크기를 분석하였다. 이렇게 분석한 분말은 일축가압 성형으로 펠렛을 제조하였으며, 이 시편은 $1200^{\circ}C$에서 소결하였다. 소결된 시편은 아르키메데스 법을 이용하여 소결밀도를 측정히였다. 전기화학적 성능을 평가하기 위해 AC impedance spectroscopy로 측정하였으며, GNP 법으로 합성된 LSF가 기존의 LSM 보다 낮은 Ohmic resistance및 Polarization resistance를 보임을 확인하였다. 또한 합성된 LSF를 양극으로 사용하여 연료극 지지체식 고체산화물 연료전지의 단위전지를 제작하였으며, 그 성능은 $750^{\circ}C$에서 $342mW/cm^2(0.7V,\;488mA/cm^2)$을 나타내었다. 마지막으로 임피던스 분석에 의하여 단위전지의 전기화학적 분극저항을 평가하였다.

• 센서학회지
• /
• 제17권1호
• /
• pp.9-14
• /
• 2008

In this paper, the gas responses of tungsten oxide films prepared by anodic reaction was discussed. Sensing electrodes and heating electrodes were patterned by photolithography method on quartz substrate. Porous tungsten oxide was fabricated in electrolyte solutions of 5 % HF (HF :$C_2H_6OH:H_2O$=3 : 2 : 20) by anodic reaction. The anodic reaction with metal (platinum wire) as a cathode and the sensing device as an anode was conducted under the various reaction times (1-10 min) at 10 mA/$cm^2$ The surface structure and morphology of the fabricated sensor have been analysed by X-ray diffraction (XRD) and field-emission scanning electron microscopy (FE-SEM). All the peaks of XRD results were well indexed to the pure phase pattern. The average diameter of the porous tungsten oxide surface were ranged about 100 nm. The fabricaed sensor showed good sensitivity to 200 ppm toluene at operating temperature of $250^{\circ}C$.

• 멤브레인
• /
• 제30권5호
• /
• pp.350-358
• /
• 2020

본 연구에서는 다공성 탄소 전극의 음극과 양극 표면에 각각 양이온교환고분자(Nafion)와 음이온교환고분자(aminated polyphenylene oxide, APPO)를 코팅하여 막 결합형 축전식 탈염(membrane capacitive deionization, MCDI) 공정에 적용하였다. 또한 위 공정의 성능을 탄소 전극만으로 구성한 축전식 탈염(capacitive deionization, CDI) 공정과 비교 평가해 보고 염 제거 효율이 최대로 나타나는 MCDI 공정의 최적 운전 조건을 탐색하고자 하였다. 염 제거 효율은 MCDI 공정이 CDI 공정에 비해 높게 나타났으며 Nafion과 APPO를 적용한 MCDI 공정에서 흡착 조건이 1.2 V, 3 min이고 탈착 조건이 -1.0 V, 1 min 일 때의 염 제거 효율이 82.1%로 최댓값을 보임을 확인했다.

• 한국세라믹학회지
• /
• 제44권12호
• /
• pp.740-746
• /
• 2007

The potential candidates for IT-SOFCs cathode materials, $Ba_{0.5}Sr_{0.5}Co_{0.8}Fe_{0.2}O_{3-{\delta}}$ (BSCF) and $La_{0.6}Ba_{0.4}Co_{0.2}Fe_{0.8}O_{3-{\delta}}$ (LBCF) powders, were synthesized by a EDTA-citrate combined method from $Sr(NO_3)_2$, $Ba(NO_3)_2$, $La(NO_3)_3{\cdot}6H_2O$, $Co(NO_3)_2{\cdot}6H_2O$, $Fe(NO_3)_3{\cdot}9H_2O$, citric acid and $EDTA-NH_3$. The cathode performance of symmetrical electrochemical cells consisting of BSCF-GDC or LBCF-GDC composite electrodes and a GDC electrolyte was investigated using by AC impedance spectroscopy at the temperature range of 500 to $700^{\circ}C$. It was found that a single phase perovskite could be successfully synthesized when the precursor is heated at $850^{\circ}C$ for 2 h. Due to thermal expansion mismatch between BSCF and GDC, the composite cathodes with lower GDC content than 45 wt% were peeled off from the GDC electrolyte and their electrode polarization resistance was estimated to be high. The thermal expansion coefficient of BSCF-GDC composites was decreased with increasing the GDC content and the electrode peeling off did not occur in BSCF-45 and 55 wt% GDC composites. BSCF-45 wt% GDC composite electrode showed the lowest area specific resistances (ASR) of 0.15 and $0.04{\Omega}{\cdot}cm^2$ at 600 and $700^{\circ}C$, respectively. On the other hand, LBCF-GDC composite cathodes showed higher ASR than the BSCF-45 and 55 wt% GDC and their cathode performance were decreased with the GDC content.

• 한국산학기술학회논문지
• /
• 제20권6호
• /
• pp.80-85
• /
• 2019

이산화바나듐은 잘 알려진 금속-절연체 상전이 물질이며, 바나듐 레독스 흐름 전지는 대규모 에너지 저장장치로 활용하기 위해서 많은 연구가 이루어져왔다. 본 연구에서는 바나듐 옥사이드 ($VO_x$) 박막을 리튬이온 이차전지의 양극으로 적용하는 연구를 수행하였다. 이를 위해서 $VO_x$ 박막을 실리콘 웨이퍼 위에 열산화공정으로 300 nm 두께의 $SiO_2$ 층이 형성된 Si 기판 및 쿼츠 기판 위에 RF 마그네트론 스퍼터 시스템으로 60분 동안 $500^{\circ}C$에서 다른 RF 파워로 증착하였다. 증착된 $VO_x$ 박막의 표면형상을 전계방출 주사전자현미경으로 조사하였고, 결정학적 특성을 Raman 분광학으로 분석하였다. 투과율 및 흡수율과 같은 광학적 특성은 자외선-가시광선 분광계로 조사하였다. Cu Foil 위에 증착된 $VO_x$ 박막을 리튬이온전지의 양극물질로 적용하여 CR2032 코인셀을 제작하였고, 전기화학적 특성을 조사하였다. 그 결과 증착된 $VO_x$ 박막은 RF 파워가 증가할수록 낟알 크기가 증가하였고, RF 파워 200 W 이상에서 증착된 박막은 $VO_2$상을 나타내었다. 증착된 $VO_x$ 박막의 투과율은 결정상에 따라 다른 값을 나타내었다. $VO_x$ 박막의 이차전지 특성은 높은 표면적을 가질수록, 결정상이 혼재될수록 높은 충방전 특성을 나타내었다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 춘계학술대회 논문집 유기절연재료 전자세라믹 방전플라즈마 일렉트렛트 및 응용기술
• /
• pp.1-5
• /
• 2002

고체산화물 연료전지는 무공해 고효율의 에너지 발전 장치이다. 연료전지는 형태는 1 세대 알카리형 연료 전지부터 인산형, 고분자전해질형, 직접메탄올형, 용융탄산염형 그리고 3세대인 고체산화물형 연료전지들이 있다. 고체산화물 연료전지는 음극 및 양극 그리고 고온에서 작동되기 때문에 전해질 및 내부연결재 등이 많이 연구 개발되고 있다. 고체산화물 연료전지는 이동형으로부터 소형발전 시스템 및 대형 복합발전시스템에 걸쳐 많이 개발이 이루어지고 있다.

• 한국방사성폐기물학회:학술대회논문집
• /
• 한국방사성폐기물학회 2004년도 학술대회지
• /
• pp.145-147
• /
• 2004