• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.14 no.1
• /
• pp.32-39
• /
• 2004

This research is to investigate the performance of a flexible matrix composite driveshaft with respect to shaft design parameters such as the number of layers, ply orientations, and material properties. A finite element formulation is utilized to estimate the allowable misalignment under given driving torque, the maximum temperature at steady states, and external damping for ensuring whirling stability under supercritical speed. Results indicate that the system performance can be greatly affected by the shaft laminate parameters, especially the ply orientations. Several sets of shaft parameters that will provide satisfactory overall system performance are derived.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1992.03a
• /
• pp.83-102
• /
• 1992

As shear localization is observed in different deformation modes, an attempt is made to understand the conditions for shear localization in general deformation modes. Most emphasis in put upon the effects of pre-localization deformation mode on the onset of shear localization and all the other well-recognized effects of subtle constitutive features and imperfection sensitivity studied elsewhere are not investigated here. Rather, an approximate perturbation stability analysis is performed for simplified isotropic rigid-plastic solids subjected to general mode of homogeneous deformation. Shear localization is possible in any deformation mode if the material has strain softening. The incipient rate of shear localization and shear plane orientations are strongly dependent upon the pre-localization deformation mode. Significant strain softening is necessary for shear localization in homogeneous axisymmetric deformation modes while infinitesimal strain softening is necessary for shear localization in plane strain deformation mode. In any deformation mode, there are more than one shear plane orientation. Except for homogeneous axisymmetric deformation modes, there are two possible shear plane orientations with respect to the principal directions of stretching. Some well-known examples are discussed in the light of the current analysis.

• Journal of Ocean Engineering and Technology
• /
• v.10 no.3
• /
• pp.34-43
• /
• 1996

In this study basic equations of fiber orientations is cimpared with experimental results. It is found that fiber orientations of short fiber reinforced polymeric composite under compression molding are governed by slope of flow speed in x-y direction. Fiber orientation angle of mold is also found to increase with closure speed and the compression ratio. At the middle of the mold, the slope of flow speed is larger in x-direction than in y-direction. At the wall of the mold, the shope of flow speed in y-direction occurs due to the effect of friction, hence affects the fiber orientation. The effect of partial flow, which incurs y-direction orientation causes to increase the fiber orientation angle at the fore part of the flow.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.7
• /
• pp.612-615
• /
• 2009

We need to control the growth orientation of CNTs on a substrate for applications to various electric devices. Generally, the flow direction of feed gases and electric field between two electrode affect to growth orientations of CNTs. In this paper, we varied tilt degrees $(0^{\circ},\;20^{\circ},\;35^{\circ},\;50^{\circ},\;65^{\circ},\;90^{\circ})$ of substrates on a cathode and DC bias voltages (0, 500, 700 V) applied between two electrodes in order to change growth orientations of CNTs. We confirmed that tilt degrees of the substrate and variation of DC bias voltages affected to the shape and orientation of the grown CNTs on the substrate.

• Tribology and Lubricants
• /
• v.5 no.2
• /
• pp.94-100
• /
• 1989

Friction and Wear behavior of continuous graphite fiber composites was studied for different fiber orientations against the sliding direction. The effect of fiber orientation on friction and wear of the composite and on the deformation of the counterface was investigated experimentally. Pin on disk type testing machine was built and employed to generate the friction and wear data. A graphite fiber composite plate was produced by the bleeder ply molding in an autoclave and machined into rectangular pin specimens with specific fiber orientations, i.e., normal, transverse, and longitudinal directions. Three different wear conditions were employed for two different periods of time, 24 and 48 hours. The wear track of the worn specimens and the metal counterface was examined with a scanning electron microscope (SEM) to observe the damaged fibers on the surface and wear film generation on the counterface. Wear mechanism of the composite during sliding wear is proposed based on the experimental results.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.19 no.1
• /
• pp.104-114
• /
• 1995

The purpose of this study were 1) to classify the consumer of outlet stole according to their patronage, 2) to investigate the differences between the patronge group and non-patronge group in 3 purchase behavior variables (shopping orientations, importance of store attributes, use of information sources) and demographic variables, and 3) to find out the reasons why consumers prefer outlet to department store's bargain sales (including clearance sales). The questionnaires were administered to 344 women living in Seoul, and the methods used to analyze the data were frequency, factor analysis, 1-test, $x^2$ test and content analysis. The results were as follows 1) outlet store consumers were classified into patronage group(n= 71) and non-patronage group(n=87). 2) There were some significant differences between patronage group and non.patronage group in 6 variables. Those who patronize outlet store does not count on the exclusiveness and the convenience of the store, enjoy common style in fashion, are price-conscious and lower in income. 3) Marketing implications were discussed according to the result of content analysis.

• ETRI Journal
• /
• v.17 no.3
• /
• pp.45-63
• /
• 1995

This paper proposes an algorithm to improve the correlation between giga-hertz transverse electromagnetic (GTEM) cell and open area test site (OATS). It is based on the dipole modeling process of an unknown source object in a GTEM cell and on the evaluation of the approximate far field equations correlated with measured GTEM powers at output port of the GTEM cell. In this algorithm, the relative phase differences between dipole moments play an important part in modeling the test object as a set of dipoles and offer stable calculation of emission values. The radiated emission test using this algorithm requires fifteen orientations of equipment under test, but the increased orientations as compared with the previous method have little effect on the time needed for testing. Radiation from a notebook computer has been tested for statistical analysis of the correlation between GTEM data and OATS data. The emission test results of the notebook computer show that the mean, the standard deviation, and the correlation coefficient are -0.62, 1.99, and +0.85, respectively. These figures indicate that this algorithm provides improved accuracy in the measurement of electromagnetic emissions over the previous method.

• Journal of Institute of Control, Robotics and Systems
• /
• v.13 no.5
• /
• pp.493-498
• /
• 2007

In this paper, a 2-dimensional accurate edge-based matching algorithm using subpixel edges is proposed that combines the Generalized Hough Transform(GHT) and the Chamfer matching to complement the weakness of either method. First, the GHT is used to find the approximate object positions and orientations, and then these positions and orientations are used as starting parameter values to find more accurate position and orientation using the Chamfer matching with distance interpolation. Finally, matching accuracy is further refined by using a subpixel algorithm. Testing results demonstrate that greater matching accuracy is achieved using subpixel edges rather than edge pixels.

• Journal of Korean Home Economics Education Association
• /
• v.11 no.2
• /
• pp.1-11
• /
• 1999

The purpose in this study is to identify beliefs about curriculum orientation of Korean secondary school home economics teachers for the development of home economics curriculum and the change of their curriculum orientation. The curriculum orientations explored were academic rationalism, technical, cognitive process, personal relevance, and social reconstruction. A mail questionnaire, Individual Curriculum Orientation Profile (ICOP), was used to survey randomly selected 525 home economics teachers. Home economics teachers agreed with the cognitive process as their predominant curriculum orientation. The second predominant type with which home economics teachers agreed most was personal relevance orientation. Home economics teachers’age, major, college type, and teaching years were significantly related to the academic rationalism curriculum orientation, and the college type for bachelor’s degree was significantly related to the technical curriculum orientation. Age and major in master’s degree were significantly related to the social reconstruction curriculum orientation.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.17 no.1
• /
• pp.94-99
• /
• 2007

In this paper, a 2-dimensional edge-based matching algorithm is proposed that combines the generalized Hough transform (GHT) and the Chamfer matching to complement weakness of either method. First, the GHT is used to find approximate object positions and orientations, and then these positions and orientations are used as starling parameter values to find more accurate position and orientation using the Chamfer matching. Finally, matching accuracy is further refined by using a subpixel algorithm. The algorithm was implemented and successfully tested on a number of images containing various electronic components.