This study was performed to find out optimum drying conditions of red pepper to minimize energy consumption and drying time, respectively, under the quality constraint using Box's complex method. The results from this study are summarized as follows. 1. From the optimization results for the drying process, energy consumption was minimized at the drying condition to minimize drying time. 2. The optimization results according to drying method was found out to be greatly affected by the quality constraint of red pepper. Especially, the turning point to change drying stage was a very important factor in the drying method with two stages.
An experimental work was conducted to develop an optimum operating system of various hay drying systems ; sun-drying with long hay, sun-drying after chopping, sun-drying after crushing, heated air drying after chopping using batch-type dryer and heated air drying after crushing using tunnel-type dryer. Seombody having 60 cm long and initial moisture content of approximately 79 % in wet basis was used for the experiment. The criteria selected for determining the optimum operating condition were the drying performance rate, the production cost and quality of dried matter of each drying systems. The result of this study are summarized as follows : 1. Drying characteristics of leaves of long stem hay, chopped seombody and crushed one were obtained by maintaining the oven temperature at 70 degrees centigrade. The required drying times for various samples to approximately 15% moisture content in wet basis were about 50 min .for leaves ; 160 min. for crushed hay ; 250 min. for chopped hay ; 340min. for ling hay and more than 360 min .for stems. The drying time of crushed hay was required about 50 % of that for the uncrushed long hay. Such a significant difference of drying of time between the leaf and long stem may indicate that an effective drying of seombody may not be achieved unless any kind of special process treatment for the whole hay is undertaken. 2. In each individual drying system, the following conclusions were drawn: a. After 8 days sun-drying on concrete floor under good days with average tempe?rature at $256{\circ}C$ and relative humidity at 55% at 2 P.M., the moisture content of long hay was still above 25 5'~ and the leaf loss during drying caused by wind and rough handling was more than 50 ~G. b. It was possible to dry the chopped seombody by sun-drying down to about 10 % moisture content within 5 days, however, a stock of heat and discolouration phenomena were observed during the drying, which may be due to the increased deposit-density by chopping, resulting in lowering the quality of the dried product. c. Sun-drying for the crushed material by hay-conditioner was required about 4 days to reduce the moisture content to about 10 %, keeping the quality of dried product at good grade. o. The optimum deposit-depth of the chopped seombody in the batch-type dryer used was about 28cm with about 42kg/hr of drying performance rate. However, it was necessary to overturn the materials between the upper and lower layers in order to obtain a good quality of dried product. d. The drying performance rate by the tunnel-type drier was highest among those of drying systems tested, giving the rate of approximately 400kg/day. 3. On reviewing the individual drying system for seombody, it was possible to draw conclusion that the best system was tunnel drying with the crushed seombody as far as the performance rate was concerned. However, the methods gives the highest operational cost. The system for the lowest operational cost with good quality of dried product was the sun-drying with the crushed material. Accordingly, it may be recommended that the system of sun-drying for the crushed seombody may be the most feasible system presently applicable to farm-level operation.
An experimental work was conducted to develop an optimum operating system of various hay drying systems ; sun-drying with long hay, sun-drying after chopping, sun-drying after crushing, heated air drying after chopping using batch-type dryer and heated air drying after crushing using tunnel-type dryer. Seombody having 60 cm long and initial moisture content of approximately 79 % in wet basis was used for the experiment. The criteria selected for determining the optimum operating condition were the drying performance rate, the production cost and quality of dried matter of each drying systems. The result of this study are summarized as follows : 1. Drying characteristics of leaves of long stem hay, chopped seombody and crushed one were obtained by maintaining the oven temperature at 70 degrees centigrade. The required drying times for various samples to approximately 15% moisture content in wet basis were about 50 min .for leaves ; 160 min. for crushed hay ; 250 min. for chopped hay ; 340min. for ling hay and more than 360 min .for stems. The drying time of crushed hay was required about 50 % of that for the uncrushed long hay. Such a significant difference of drying of time between the leaf and long stem may indicate that an effective drying of seombody may not be achieved unless any kind of special process treatment for the whole hay is undertaken. 2. In each individual drying system, the following conclusions were drawn: a. After 8 days sun-drying on concrete floor under good days with average tempe\ulcornerrature at $256{\circ}C$ and relative humidity at 55% at 2 P.M., the moisture content of long hay was still above 25 5'~ and the leaf loss during drying caused by wind and rough handling was more than 50 ~G. b. It was possible to dry the chopped seombody by sun-drying down to about 10 % moisture content within 5 days, however, a stock of heat and discolouration phenomena were observed during the drying, which may be due to the increased deposit-density by chopping, resulting in lowering the quality of the dried product. c. Sun-drying for the crushed material by hay-conditioner was required about 4 days to reduce the moisture content to about 10 %, keeping the quality of dried product at good grade. o. The optimum deposit-depth of the chopped seombody in the batch-type dryer used was about 28cm with about 42kg/hr of drying performance rate. However, it was necessary to overturn the materials between the upper and lower layers in order to obtain a good quality of dried product. d. The drying performance rate by the tunnel-type drier was highest among those of drying systems tested, giving the rate of approximately 400kg/day. 3. On reviewing the individual drying system for seombody, it was possible to draw conclusion that the best system was tunnel drying with the crushed seombody as far as the performance rate was concerned. However, the methods gives the highest operational cost. The system for the lowest operational cost with good quality of dried product was the sun-drying with the crushed material. Accordingly, it may be recommended that the system of sun-drying for the crushed seombody may be the most feasible system presently applicable to farm-level operation.
This study was carried out to define the optimum drying conditions for Lycium chinense Miller as a useful healthy food, because recently the cultivation area and yield of this fruit are increased. The experiments of two varieties were performed at the temperature of $45^{\circ}C$, $50^{\circ}C$, $55^{\circ}C$ and $60^{\circ}C$. The drying ratio was the slowest and quality was the best at the drying temperature of $45^{\circ}C$. The drying temperature was higher, drying ratio was more faster and the quality became worse. The difference of drying ratios between the varieties was insignificant. The energy consumption per hour was the minimum at the drying temperature of $45^{\circ}C$, but the total energy consumption was the maximum for the long drying time. Also, the energy consumption at the drying temperature $50^{\circ}C$, $55^{\circ}C$ and $60^{\circ}C$ was not very different from others. Considering the drying ratio, quality and energy consumption, the drying time of 36 hours at the drying temperature of $50^{\circ}C$ was the most optimum condition.
간편하게 경제적으로 운용할 수 있는 마이크로컴퓨터 건조시스템을 개발하여 양파와 생강을 대상으로 건조실험을 수행하였다. 개발한 건조시스템은 마이크로컴퓨터에 의해 온도, 습도 및 무게를 자동으로 측정 및 제어하여 양질의 건조제품을 얻을 수 있었다. 양파는 $65^{\circ}C$의 건조온도에서 건조실내의 상대습도를 25%로 조절하는 것이 적정 건조조건으로 나타났으며, 생강의 적정 건조조건은 $50^{\circ}C$의 건조온도와 25%의 상대습도로 나타났다.
This study has been analyzed and investigated the possibility for the substitution of a heat source with the application of PTC(Positive Temperature Coefficient Heater) in a food drying machine. And this experiment was conducted to measure temperatures at the upper part of the vessel and the heat sink. And the structure has the many holes plane connected with the external air in the upper part of similar volumetric vessel, and attached to the PTC heater (3sets) of total consumption electricity of 120[W] in Al radiant heat structure and the small fan (2sets) in the suitable space of the lower part. Consequently, it was found that at the most conditions of food drying test with the seven holes(5mm) under the control temperature $62^{\circ}C$, the optimum drying condition formatted and the optimum time range especially appeared from 6,500 second to 7,000 second in case of drying test on banana sample.
Several presowing seed treatments have been used to facilitate the seed germination and seedling emergence. The study was performed to design a model of presowing seed treatments in Taraxacum platycarpum. Germination and seedling growth responses to temperature, drying, chilling, $GA_3$ and priming were investigated to know the optimum germination conditions and presowing treatment. The optimum temperature condition for germination and seedling growth were $15{\sim}20^{\circ}C$ at dark condition. The seeds exposed to infra red light, however, did not germinate. The moisture content of seeds dried at $35^{\circ}C$ for 3.5 hours was returned to the level of unimbibed seeds. The germination of seeds dried under dark condition was better than those dried under infra red light. Prechilling treatment imposed for 6 weeks showed higher germination rate than $GA_3$ treatment or priming. In field test, the highest field emergence was observed in the seeds dried after prechilled for 6 weeks and followed by drying followed by $GA_3$ > low temperature > $KNO_3$ priming. Imbibition with 0.1 mM $GA_3$ solution for 2 hours then drying at 35 for 3.5 hour under dark condition was effective to the practical presowing treatment for Taraxacum seeds.
The purpose of this study is to predict the performance of a cyclone drying machine and air ejector used in drying applications. This paper deals with optimization of the geometry of the ejector for sludge drying using computational fluid dynamics. To facilitate the design of a jet ejector for air drying machines, a numerical model of simultaneous mass and heat transfers between the liquid(sludge) and gas(air) phases in the jet ejector was developed. The steady-state model was based on unidimensional balance equations of mass, energy and momentum for the liquid and gas phases. It was shown that the optimum condition to minimize pressure and momentum loss of air in the ejector was d=220mm. It was found that sludge particles inside the cyclone was smoothly discharged by the conical wedge installed on the bottom of the cyclone.
Optimum drying conditions to utilize porcine blood from slaughter house for blood meals, and the effects of blood meals on growth in broiler chicks were investigated. Moisture and protein con-tents of slaughter porcine blood were 79.8 and 16.4%, respectively. The protein contents of the flash dried blood meals at 80˚C were not different from those of the spray dried blood meals at 160 and 190˚C, but higher by 17% relative to those of the spray dried blood meals at 80 and 120˚C. Results from protein analysis by SDS-polyacrylamide electrophoresis showed that flash dried blood meals at 80˚C and spray dried blood meals at 160˚C were better than spray dried blood meals at 80, 120 and 190˚C in terms of protein quality. In Feeding Trial I with broiler chicks, body weights of chicks fed 2, 4 and 6% flash dried blood meal diets at 80˚C were increased at 35 days by 5.6, 7.9 and 4.0%, respectively, compared to control group(P<0.05). In Feeding Trial II, body weights of chicks fed 4 and 6% flash dried blood meal diets at 80˚C were increased at 42 days by 4.9 and 5.3%, respectively, compared to control group(P<0.05). Feed conversion ratios of chicks fed diets 4 and 6% flash dried blood meal diets at 80˚C were significantly improved at 42 days by 7.0 and 3.7%, respectively, compared to that of control group(P<0.05). The optimum drying condition of slaughter porcine blood seemed to be the flash drying method at 80˚C
아가리쿠스 버섯에 있어 각 온도별 건조 품질을 살펴보았다. 우선 갓과 대의 건조시간은 5$0^{\circ}C$에서 모두 29시간이었으며 10$0^{\circ}C$의 경우 갓과 대 모두 10시간 소요되었으며 실온에서 음건할 때에는 갓과 대가 모두 3일 정도 소요되었다. 수분감소율은 온도가 높을수록 켰으며, 부위별로는 5$0^{\circ}C$에서 초기감소율이 갓보다 대가 크게 나타났으며 최종수분함량은 갓이 대보다 적었다. 반면에 10$0^{\circ}C$와 실온에서 갓의 수분감소율이 켰으며, 최종수분함량은 갓이 적었다. 수분활성도는 갓과 대가 모두 실온에서 음건, 5$0^{\circ}C$, 10$0^{\circ}C$의 순으로 낮았다. 수화복원력은 갓과 대 모두가 건조온도와는 관계없었으며, 실온에서 침지 120분까지 급격히 증가하여 이때에 최대치를 나타내었다. 색도는 갓에서의 전체적으로 건조 온도가 상승함에 따라 백색도를 나타내는 L 값이 낮아지는 것으로 조사되었다. 세부적으로는 L 값이 5$0^{\circ}C$에서의 시료가 가장 높았고 생것이 가장 낮았다. a 값은 생시료가 가장 높았고, 10$0^{\circ}C$ 건조시료가 가장 낮았다. b 값은 10$0^{\circ}C$에서 건조시료가 가장 높았고 생것이 가장 낮았다. 갈변도는 건조온도가 높을수록 높았으며 갓이 대보다 켰다. 이는 온도 상승이 건조 아가리쿠스의 품질을 저하한다는 것을 보여주었다. 관능검사결과 건조온도가 상승함에 따라 색과 외관품질이 떨어지는 것으로 조사되었다. 하지만 향에 있어서 건조 온도가 5$0^{\circ}C$이상에서 전체적으로 좋은 향이 나오는 것으로 확인되었다 결과적으로 5$0^{\circ}C$의 건조온도에서 아가리쿠스를 열풍 건조하는 것이 경제적 뿐만 아니라 품질면에서 가장 좋은 조건이라 조사되었다. 뿐만 아니라 아가리쿠스의 약리성분들은 열에 강한 특성이 있으므로 5$0^{\circ}C$에서 건조하여도 충분히 기능성 및 약리성에 영향이 없을 것으로 사료되었다. 하지만 앞으로 아가리쿠스의 약리성분을 중심으로 조에 온도에 따른 영향을 조사하여 적정온도를 결정할 수 있는 연구가 필요하리라 생각된다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.