• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.04a
• /
• pp.387-392
• /
• 1999

The bond performance of prestressing strands is still not well understood and is still in controversy on the validity of the test results up to today, although it is a basic information to desing the prestressed pretensioned concrete beams. Different transfer length has been found for a product of the same company, but of the different production methods and factories in the United States. It is necessary to determine optimum transfer bond length of the domestic stands because the ultimate flexural and shear capacity in a section of prestressed concrete beams are evaluated under the assumption that the anchorage bond failure shall not happen. The transfer lenght of low-relaxation, Gr 270, and 1/2" seven-wire prestressing strands from four domestic companies will be evaluated by the concrete strain method. The recent concept of the 95% Maximum Average Strain Method suggested by Russel et al. will be considered to obtain the transfer length of domestic strands. It will be also evaluated if the domestic strands are conform to ACI 318-95.8-95.

• Proceedings of the KSME Conference
• /
• 2001.11b
• /
• pp.229-234
• /
• 2001

The thermoacoustic refrigerator bas not only considerable possibility but also commercial usability, because it bas high reliability, lower vibration, no moving part, and can easily be constructed. In this study, the resonance characteristics of the thermoacoustic refrigerator were investigated for better performance, varying length of the resonance tube to 400mm, 500mm, 600mm, 700mm. In order to determine the optimum resonance tube length and the frequency, the $\lambda/4$ thermoacoustic engine and the similar apparatus of Wheatly type refrigerator were constructed. It was used air as a coolant. in the fifth harmonic, it was taken the highest ${\Delta}t$ that was $56.3^{\circ}C$ at 626Hz in 400mm tube with 40mm stack.

• Plant Resources
• /
• v.4 no.2
• /
• pp.97-101
• /
• 2001

This study was carried out to determine the effect of sowing time on the flowering, growth and yield of Schizonepeta tenuifolia Briquet. Emergence and flowering dates in the sowing time from March 30 to April 30 were earlier than those of the other sowing times. In the sowing time from March 30 to April 30, length and diameter of main stem, number of node per main stem, number of branch per plant and fresh, and dry weight of stem were greater than those of the other sowing times. Yield components such as ear length, main stem length and diameter, branches per plant, number of node and ears per plant, yield of stem in fresh and dry were the highest at the sowing time from March 30 to April 30. Optimum sowing time of Schizonepeta tenuifolia Briquet were shown to be from March 30 to April 30 in southern areas of Korea.

• International Journal of Precision Engineering and Manufacturing
• /
• v.7 no.2
• /
• pp.56-59
• /
• 2006

A vibrational model of powder transfer equipment based on the lumped parameter method was developed, in which the operating motion consists of surging, bouncing, and pitching. After decoupling the equation of motion, the vibrational excitation source of the pitching motion was removed. So the designers are able to plan the optimum design to adjust the motion trajectory of the powder transfer equipment. That is, a procedure to adjust the motion trajectory of powder transfer equipment by changing design specifications such as the installation position, the direction of the motor, the driving speed, the mass unbalance, the stiffness coefficient, and the installation position of the support spring, is presented in this paper. The powder transfer equipment manufactured according to the results of this study did not suffer fatigue destruction, since the maximum stress on the basket structure was sufficiently small.

• 유체기계공업학회:학술대회논문집
• /
• 2005.12a
• /
• pp.185-190
• /
• 2005

This work presents a numerical procedure to optimize the elliptic-shaped pin fin arrays to enhance turbulent heat transfer. The response surface method is used as an optimization technique with Reynolds-averaged Navier Stokes analysis of flow and heat transfer. Shear stress transport (SST) turbulence model is used as a turbulence closure. Computational results for average heat transfer rate show a reasonable agreement with the experimental data. Four variables including major axis length, minor axis length, pitch and the pin fin length nondimensionalized by duct height are chosen as design variables. The objective function is defined as a linear combination of heat transfer and friction-loss related terms with weighting factor. D-optimal design is used to reduce the data points, and, with only 28 points, reliable response surface is obtained. Optimum shapes of the pin-fin arrays have been obtained in the range from 0.0 to 0.1 of weighting factor.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.25 no.2
• /
• pp.182-187
• /
• 1988

Hot carrier induced device degradation characteristics under DC bias stress have been investigated in n-MOSFETs with channel length of 1.2,1.8 um, and compared with those of LDD structure device with same channel length. Based on these results, the device lifetime in normal operating bias(Vgs=Vds=5V) is evaluated. The lifetimes of conventional and LDD n-MOSFET with channel length of 1.2 um are estimated about for 17 days and for 12 years, respectively. The degradation rate of LDD n-MOSFET under the same stress is the lowest at n-region implnatation dose of 2.5E15 cm-\ulcorner while the substrate current is the lowest at the dose of 1E13cm-\ulcorner Thses results show that the device degradation characteristics are basic measurement parameter to find optimum process conditions in LDD devices and evaluate a reliability of sub-micron device.

• Plant Resources
• /
• v.6 no.2
• /
• pp.94-97
• /
• 2003

The objective of this study is to investigate morphological characteristics of seeds and effects of environmental factors such as light and temperature on the germination and seedling growth of Adenophora triphylla var. japonica, Codonopsis lanceolata, Platycodon glandiflorum, Which belongs to Campanulaceae and useful for on oriental medicine materials. Seed shape of Codonopsis lanceolata is Elliptic. Platycodon glandiflorum is Oblong. Color of seed coats varied from yellow to dark brown. Seed size of Adenophora triphylla var. japonica is 1.37mm in length, 0.69mm in width. One thousand-seed weight of Adenophora triphylla var. japonica is 258mg. Seed size of Codonopsis lanceolata is 4.45mm in length, 2.11mm in width. One thousand-seed weight of Codonopsis lanoceolata is 1,278mg. Seed size of Platycodon glandiflorum is 2.31mm in length, 1.10mm in width. One thousand-seed weight of Platycodon glandiflorum is 988mg. Optimum temperatures for seed germination and seedling growth range from 20 to $25^{\circ}C$.

• Proceedings of the Korean Society of Agricultural Engineers Conference
• /
• 1999.10c
• /
• pp.289-293
• /
• 1999

This research was performed to evaluate the longitudinal length change ratio of concrete used the expansive admixture. As the results of this study, the compressive strength was shown the highest value at the used 10% expansive admixture both of the dry and wet curing condition. And the length change ration was shown higher 0.0316% and 0.0529 % than that of control in wet and dry curing condition. But this value was not enough to recover the shrinkage occuring by dry shrinkage. According to this study , we have obtained 10% on normal portland cement concrete as the optimum replacement ration of expansive admixture.

• Journal of Ginseng Research
• /
• v.12 no.1
• /
• pp.40-46
• /
• 1988

This study was conducted to investigate the optimum temperature and light intensity of photosynthesis and transmittance in the shade for better growth and root yield of ginseng. The 3-year-old ginseng plants grown under the shade of 5, 10 and 20% transmittance did not show any significant difference in the stem length, stem diameter, leaf area and root length. The root diameter markedly increased under the shade of 10% and 20% transmittance, and the root was the heaviest under the shade of 20% transmittance. The 6-year-old ginseng plants grown at 20% transmittance showed the largest root diameter but the root length was not influenced by transmittance. The root was heaviest in the shade of 20% transmittance.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• v.2
• /
• pp.247-250
• /
• 2006

Based on the possibility theory and the fuzzy set, the Maximum Possibility Estimation method and its applications in kinematic GPS positioning are presented in this paper. Firstly, the principle and the optimal criterion of the Maximum Possibility Estimation method are explained. Secondly, the kinematic GPS positioning model of single epoch single frequency with baseline length constraint is developed. Then, the authors introduce the artificial immune algorithm and use this algorithm to search the global optimum of the Maximum Possibility Estimation model. The results of some examples show that the method is efficient for kinematic GPS positioning.