• Journal of the Korea Concrete Institute
• /
• v.27 no.4
• /
• pp.443-450
• /
• 2015

This paper presents an investigation of the mechanical and microstructural properties of Class F fly ash based geopolymer containing sodium sulfate as an additive. Sodium sulfate was used as an chemical additive at the dosage levels of 0, 2, 4, and 6wt% of fly ash. Sodium hydroxide and sodium silicate solutions were used to activate fly ash. The compressive strengths of geopolymer pastes were measured at the age of 28 days. The microstructures of the geopolymer pastes were examined using XRD, MIP and SEM tests. The additions of 2wt% and 4wt% sodium sulfate produced geopolymers with high strength, while increasing the dosage of levels to 6% resulted in almost no changes in strength, comparing with the control geopolymer. The optimum increase in strength was obtained with the addition of 4wt% sodium sulfate. As the amount of sodium sulfate is increased, no additional crystalline phase was detected and no change of amorphous phase indicated despite the change in the strength development. The increase in the strength was due to the change of pore size distribution in samples. As addition of sodium sulfate altered the morphologies of reactive productions and Si/Al ratios of the reaction products, the strengths were thus affected. It was found that the strengths of geopolymer were larger for lower Si/Al ratios of reaction products formed in samples. The optimal amount of sodium sulfate in the fly ash based geopolymer helps to improve mechanical properties of the geopolymer, on the other hand, the high percentage of sodium sulfate could exist as an impurity in the geopolymer and hinder the geopolymer reaction.

• Journal of Korean Society of Environmental Engineers
• /
• v.30 no.8
• /
• pp.839-846
• /
• 2008

The flocculation characteristics of polyacrylamide base flocculants were estimated to reduce the moisture content of the dehydrated cakes. The dewaterability for sewage sludge was found to have a marked effect depending on the flocculant type, agitating speed and time, kind of dissolution water, etc. The optimal agitating speed and time were 700 rpm and 3 sec, respectively, in this experimental condition. and the dewaterability was proportion to the agitating speed upto 700rpm. When recycle water as the dissolution water was used, the solution viscosity of all kind of flocculants was decreased. However, the change of its viscosity are not proportioned to the dewaterabilities for each flocculant. Flocculation system of combinations of the first and sencond flocculation using single flocculant was investigated. Effects of the ratio of first and second dosage for dual flocculation on the dewaterability were also investigated. The optimum conditions of dual flocculation system are 75% and 50% as first dosages for low and high viscous flocculant for total dosage of common flocculation, respectively. Based on the results, an overall mechanism of dual flocculation system is proposed and it is envisaged that optimization of flocculation processes in this way can result in considerable savings in cost.

• Journal of the Korea Concrete Institute
• /
• v.26 no.3
• /
• pp.277-285
• /
• 2014

The purpose of this study is to investigate experimentally the variation factors range having influence on the rheological properties of the combined self-compacting concrete according to materials quality, weighting error and site conditions. Two types cement (blast-furnace slag cement and belite cement), lime stone powder as binder and the optimum mix proportions in the preceded study are selected for this study. Also, variations for sensitivity test are as followings; (1) Concrete temperature 3 cases (2) Surface moisture of sand 5cases (3) Fineness modulus of sand 5cases (4) Specific surface of lime stone powder 3cases (5) Dosage of chemical admixture 5cases. Slump flow ($650{\pm}50mm$), 500 mm reaching time (($7{\pm}3sec$), V-type flowing time ($15{\pm}5sec$) and U-box height (min. 300 mm) are tested for sensitivity. As test results, the variations range for quality control are as followings. (1) Concrete temperature; $10{\sim}20^{\circ}C$(below $30^{\circ}C$) (2) Surface moisture of sand; $base{\pm}0.6%$ (3) Fineness modulus of sand; $2.6{\pm}0.2$ (4) Dosage of chemical admixture; $base{\pm}0.2%$ (5) Specific surface of lime stone powder $6000cm^2/g$. Compared with two types cement including based belite cement (binary type) and based slag cement (ternary type), the combined self-compacting concrete used belite cement type is most stable in the quality control because of high contents for lime stone powder and $C_2S$. It is to propose a control scheme of the combined self-compacting concrete in the actual construction work.

• Asian-Australasian Journal of Animal Sciences
• /
• v.30 no.7
• /
• pp.1006-1012
• /
• 2017

Objective: This study was conducted to investigate effects of zinc (Zn) bearing palygorskite (ZnPal) supplementation on growth performance, hepatic mineral content, and antioxidant status of broilers at early age. Methods: A total of 240 1-day-old Arbor Acres broiler chicks were allocated into 5 treatments with 6 replicates of 8 chicks each. Birds in 5 treatments were fed a basal diet supplemented with 0 (Control group; Analyzed Zn content: 81 mg/kg), 20, 40, 60, and 80 mg/kg Zn as ZnPal for 21 days, respectively. Blood, liver and intestinal mucosa were collected at 21 days of age. Results: Treatments did not affect growth performance of broilers during the 21-day study (p>0.05). The contents of hepatic Zn and magnesium (Mg) were linearly increased (p<0.001) by ZnPal supplementation. ZnPal inclusion linearly (p = 0.007) reduced malondialdehyde (MDA) concentration in serum. The activity of total superoxide dismutase (T-SOD) in liver increased linearly (p = 0.001) with concentration of ZnPal in diet. ZnPal inclusion linearly (p = 0.036) and quadratically (p = 0.005) increased T-SOD activity, and linearly (p = 0.012) increased copper/zinc superoxide dismutase (Cu/Zn SOD) activity in jejunal mucosa. The maximum responses of hepatic and jejunal antioxidant enzymes activities (T-SOD and Cu/Zn SOD) were found when supplementing the basal diet with 60 mg/kg Zn as ZnPal. Furthermore, ZnPal supplementation quadratically (p = 0.001) increased Cu/Zn SOD activity in ileal mucosa, and its maximum activity was observed in the diet supplemented with 20 mg/kg Zn as ZnPal. Conclusion: ZnPal supplementation did not alter growth performance of broilers. Dietary ZnPal inclusion could increase concentrations of hepatic trace minerals (Zn and Mg) and inhibit lipid peroxidation by reducing serum MDA accumulation, with the optimal dosage of Zn from ZnPal being 80 mg/kg diet (analyzed Zn content in the diet: 165 mg/kg), and 60 mg/kg Zn as ZnPal (analyzed Zn content in the diet: 148 mg/kg) was the optimum dosage for broilers to achieve maximum antioxidant enzyme activities.

• Korean Chemical Engineering Research
• /
• v.45 no.6
• /
• pp.648-655
• /
• 2007

UV/H_2O_2$, $O_3$, $O_3/H_2O_2$, $UV/H_2O_2/O_3$ processes were tested for the removal of COD and color from terephthalic acid wastewater. COD removal efficiencies were 10, 48, 56, 63% in the $UV/H_2O_2$, $O_3$, $O_3/H_2O_2$, $UV/H_2O_2/O_3$ process respectively. Color removal efficiency of $UV/H_2O_2$ process was 80% and $O_3$, $O_3/H_2O_2$, $UV/H_2O_2/O_3$ processes were almost more than 99%. Terephthalic acid, isophthalic acid and benzoic acid were completely destructed in terephthalic wastewater within 120 min by $UV/H_2O_2/O_3$ process and shows high COD and color removal efficiencies. The optimum concentration of $H_2O_2$ dosage was found to be 0.5 M, 25 mM and 5 mM for $UV/H_2O_2$, $O_3/H_2O_2$ and $UV/H_2O_2/O_3$ processes respectively, Organic destruction efficiency was enhanced and also reducing the consumption of $H_2O_2$ dosage by combining UV, $H_2O_2$ and $O_3$ process.

• Journal of Korean Society of Water and Wastewater
• /
• v.21 no.4
• /
• pp.503-508
• /
• 2007

Small scale D-water treatment plant(WTP) where has slow sand filtration was using raw water containing high concentration of manganese (> 2mg/l). The raw water was pre-chlorinated for oxidation of manganese and resulted in difficulty for filtration. Thus, sometimes manganese concentration and turbidity were over the water quality standard. Two stage rapid manganese sand filtration pilot plant which can treat $200m^3/d$ was operated to solve manganese problem in D-WTP. The removal rate of manganese and turbidity were about 38% and 84%, respectively without pH control of raw water. However, when pH of raw water was controlled to average 7.9 with NaOH solution, the removal rate of manganese and turbidity increased to 95.0% and 95.5%, respectively and the water quality of filtrate satisfied the water quality standard. Manganese content in sand was over 0.3mg/g which is Japan Water Association Guideline. The content in upper filter was 5~10 times more than that of middle and lower during an early operation but the content in middle and lower filter was increased more and more with increase of operation time. This result means that the oxidized manganese was adsorbed well in sand. Rapid manganese sand filter was backwashed periodically. The water quality of backwash wastewater was improved by sedimentation. Thus, turbidity and manganese concentration decreased from 29.4NTU to 3.09NTU and from 1.7mg/L to 0.26mg/L, respectively for one day. In Jar test of backwash wastewater with PAC(Poly-aluminum chloride), optimum dosage was 30mg/L. Because the turbidity of filtrate was high as 0.76NTU for early 5 minute after backwash, filter-to-waste should be used after backwash to prevent poor quality water.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.10
• /
• pp.3311-3316
• /
• 2012

In this paper, a layered-carbon-$Fe_3O_4$ (LC-$Fe_3O_4$) hybrid material was synthesized through a facile one-pot solvothermal method and used as the adsorbent for the preconcentration of some phthalate esters (dimethyl phthalate, diethyl phthalate, diallyl phthalate, diisobutyl phthalate and benzyl butyl phthalate) in water samples. The effects of the adsorbent dosage, extraction time, the solution pH and salinity on the adsorption of the phthalate esters (PAEs) were investigated. The magnetic nanocomposite adsorbent could remove and enrich the PAEs from water samples efficiently. After the adsorption, the analytes were desorbed and then determined by high performance liquid chromatography-ultraviolet detection. Under the optimum conditions, the enrichment factors of the method for the analytes were in the range from 161 to 180. A linear response with peak area as the quantification signal was observed in the concentration range from 0.5 to $100ng\;mL^{-1}$. The limits of detection (S/N = 3) of the method were between 0.08 and $0.1ng\;mL^{-1}$. The method was suitable for the determination of trace phthalate esters in environmental water samples.

• Applied Chemistry for Engineering
• /
• v.10 no.7
• /
• pp.1073-1078
• /
• 1999

The objectives of this study are to examine the applicability of waste slurry from soda ash manufacturing industries as a coagulant for the treatment of wastewater containing fine silica particles, and to reduce the cost of wastewater treatment containing silica. Acceptable water quality can be obtained with a little dosing of waste slurry by gelation before the coagulation process so it could be concluded that the waste slurry from soda ash can be used as a coagulant. Based on the results of experiments, the optimum pH of gelation for silica in wastewater was around five and the treatment process with the gelation of silica could reduce the chemical dosage and waste sludge after coagulation. Dewatering and settling characteristics of the floc after coagulation with the waste slurry are better than those of the floc after coagulation with the lime milk only.

• KSBB Journal
• /
• v.24 no.6
• /
• pp.579-583
• /
• 2009

The effects of cell lytic enzyme treatment on total phenolic content, antioxidant and antityrosinase activities of lotus leaf were investigated. The dried lotus leaves were hydroyzed by cell lytic enzymes such as Promozyme, Ceremix, Pectinex, Ultraflo, Celluclast, Pentopan, Tunicase, Viscozyme at their optimum pHs (pH 5-8) at $50^{\circ}C$ for 4 hrs. Depending on the enzymes used, total phenolic compounds content was measured as $1,079-1,476{\mu}g$/mL, and antioxidant activities and whitening activities were increased by 5~10% and 20%, respectively Among the tested hydrolytic enzymes, Promozyme (pullulanase) was selected as the most suitable enzyme for the extraction of total polyphenol from lotus leaf. The optimal dosage of Promozyme were found to be 1-2% (w/w). By Promozyme treatment, total phenolic compounds content of the lotus extract significantly increased compared to the extraction without enzyme treatment.

• Advances in environmental research
• /
• v.9 no.1
• /
• pp.65-84
• /
• 2020

The potential use of Sargassum boveanum algae for the removal of uranium from aqueous solution has been studied by varying three independent parameters (pH, initial uranium ion concentration, S. boveanum dosage) using a central composite design (CCD) under response surface methodology (RSM). Batch mode experiments were performed in 20 experimental runs to determine the maximum metal adsorption capacity. In CCD design, the quantitative relationship between different levels of these parameters and heavy metal uptake (q) were used to work out the optimized levels of these parameters. The analysis of variance (ANOVA) of the proposed quadratic model revealed that this model was highly significant (R² = 0.9940). The best set required 2.81 as initial pH(on the base of design of experiments method), 1.01 g/L S. boveanum and 418.92 mg/L uranium ion concentration within 180 min of contact time to show an optimum uranium uptake of 255 mg/g biomass. The biosorption process was also evaluated by Langmuir, Freundlich, Temkin and Dubinin-Radushkevich isotherm models represented that the experimental data fitted to the Langmuir isotherm model of a suitable degree and showed the maximum uptake capacity of 500 mg/g. FTIR and scanning electron microscopy were used to characterize the biosorbent and implied that the functional groups (carboxyl, sulfate, carbonyl and amine) were responsible for the biosorption of uranium from aqueous solution. In conclusion, the present study showed that S. boveanum could be a promising biosorbent for the removal of uranium pollutants from aqueous solutions.