• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.10a
• /
• pp.549-554
• /
• 2002

In Powder System, SCC demands high dosage of superplasticizer and a lage amout of powder for suitable fluidity and viscosity. Okamura's method of most representative mixing design method in SCC of Powder-System is unfavorable economically because of using a large amount of powder. In addition, many ready-mixed concrete plants do not use his mix design method and procedure due to complexity for practical application. Therefore, Nan Su proposed more simple mix design method than Okamura's. It had an advantage in simplicity in practical application and required a smaller amount of powders compared with Okamura's method. This paper proposed an optimal mixture proportion of SCC with consideration of Nan Su's method. The new and modified mix design method required a smaller amount of powder than that of Nan Su's. To check the properties of SCC, considered with the requirements specified by the Japanese Society of Civil Engineering.(JSCE)

• Journal of the Korean Operations Research and Management Science Society
• /
• v.24 no.2
• /
• pp.81-94
• /
• 1999

ATM network design procedure is different from the current circuit or packet networks design procedure because of the variety of the offered services and the variability of requested bandwidth for each connection of ATM network. A number of optimization models for the link dimensioning of ATM network design have been proposed in the literature. However, most of the literature did not consider the modularity of resources allocated to a transmission path and the non-bifurcation of a VP link over the more than one TP, which are standardized in recent ITU-T Recommendations. In thIs paper, we propose a mathematical model for link dimensioning of ATM networks, based on the network synthesis method and a generalized bin-packing problem. The suggested model satisfies the constraints mentioned in the ITU-T Recommendations. We also propose efficient and practical algorithms for the suggested model. Computational experiment shows that the suggested algorithm gives efficient solutions even for moderate and large-sized networks within reasonable time.

• Journal of Korean Institute of Industrial Engineers
• /
• v.32 no.3
• /
• pp.219-225
• /
• 2006

We consider a routing and wavelength assignment (RWA) for the efficient operation of WDM networks. For a given physical network, a set of selected pairs of nodes, the number of required connections for each selected pair of nodes, and a set of available wavelengths, the RWA is to realize as many connections as possible without wavelength collision. We give an integer programming formulation and an algorithm based on column generation. Though the proposed algorithm does not guarantee optimal solutions, test results show that the algorithm gives probably good solutions.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.14 no.1
• /
• pp.44-50
• /
• 2015

This paper presents a heuristic process-optimization procedure for minimizing warpage in injection-molded parts based on the dynamic robust design methodology. The injection molding process is known to have intrinsic variations of its process conditions due to various factors, including incomplete process control facilities. The aim of the robust design methodology advocated by Taguchi is to determine the optimum design variables in a system which is robust to variations in uncontrollable factors. The proposed procedure can determine the optimal robust conditions of injection molding processes at a minimum cost through a trade-off strategy between the degree of warpage and the packing time.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.7
• /
• pp.500-505
• /
• 2012

In this study, the influence of the intermolecular distance on the charge mobility in a pentacene thin-film was investigated. In order to increase the mobility which depends on the ${\pi}$-overlap between molecules, the intermolecular distance was shortened by compressive force along the conduction channel. Pentacene thin-film was fabricated on flexible substrates bent outward at different radii to stretch the gate dielectric surface and then the substrates were unbent, producing the compressive force to the film. The result showed that the mobility increased proportionally to the strain applied during the pentacene deposition and the molecular packing inside a grain was not optimal for the charge transport.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.577-578
• /
• 2006

In this paper, the rubber behavior was calculated for obtaining the optimal process condition which is for producing a transformer with a given performance. This study was carried out using the computer simulation of injection mold filling and packing simulations. In order to remove the crack of product, proper locations of the runner and cooling system configurations could be determined. Based on these results, the transformer is developed by injection molding and guidelines of part design, mold design and processing conditions are established. Finally, the cast savings, cycle time reduce and improvement of productivity will be obtained.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.9 no.5
• /
• pp.28-33
• /
• 2010

A computer code was developed to simulate all three stages of the injection molding process: filling, packing and cooling by finite element method. The constitutive equation used here was compressible Leonov model. The PVT relationship was assumed to follow the Tait equation. The flow-induced birefringence was related to the calculated flow stresses through the linear stress-optical law. Based on the simulation, the Taguchi method was used to investigate the influences of injection molding conditions on the birefringence of a center gate disk. In addition, the optimal processing conditions were selected to minimize the birefringence and the birefringence difference along the positions of the disk.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.16 no.6
• /
• pp.21-28
• /
• 2007

Injection molding process factors such as molding temperature, injection pressure, flow rate and flow velocity, must be controlled properly in filling and packing phases in the injection molding process. In this study, effects of these factors on the injection molding were investigated through the flow analysis for birefringence and refractive index for pickup lens. This paper presents the birefringence and refractive index reduced with increasing the holding pressure and also the holding pressure time. And there are interaction with birefringence and fill time in the injection process. The optimal conditions through DOE are validated by using injection molding analysis.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.305-309
• /
• 2005

A computer code was developed to simulate all three stages of the injection molding process ? filling, packing and cooling by finite element method. The constitutive equation used here was compressible Leonov model. The PVT relationship was assumed to follow the Tait equation. The flow-induced birefringence was related to the calculated flow stresses through the linear stress-optical law. Based on the simulation, the Taguchi method was used to investigate the influences of injection molding conditions on the birefringence of a center gate disk. In addition, the optimal processing conditions were selected to minimize the birefringence and the birefringence difference along the positions of the disk.

• The Magazine of the Society of Air-Conditioning and Refrigerating Engineers of Korea
• /
• v.14 no.1
• /
• pp.31-38
• /
• 1985

By using the hollow shaft with $0.5^{\circ}$ internal taper, ball valve and rubber packing, charging the working fluid at engineering vacuum degree (vacuum pressure higher than 1 torr) and carrying out experiments, it was investigated the performance of rotating heat pipe with variant operating conditions. In this experiment, it was shown that it is impossible the internal liquid flow was laminar film flow which agree with the assumption of present theoretical analyses, but the internal vorticity makes the heat transfer increase and for the maximum heat transfer there is optimal mass loading for the given heat pipe geometry and operational conditions.