• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.949-950
• /
• 2011

There are various ways of optimizing rotor design of Interior Permanent Magnet Synchronous Motors(IPMSM). In this paper, the best optimized design value was found by varying the Bridge thickness of PM in the rotor and changing Rib. The set design values were torque, 5 harmonics, 7 harmonics, and safety factor. Also, in order to make practical design value easily and quickly for optimization, Box-Behnken of Response Surface Method(RSM) method was used. Therefore, IPMSM resulted an optimized design model with high torque, low harmonics, and constant value of safety factor.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.4
• /
• pp.699-704
• /
• 2007

In this paper, optimized model was designed for the starting characteristic of the Single-Phase Line-Start Permanent Magnet Synchronous Motor by using the Design of Experiment. A field pole angle, thickness and distance from center axis of permanent magnet were selected as design factor. We executed the transient state characteristic analysis of 8 test models. The transient state characteristic analysis was executed by using the 2 dimensional Finite Element Method and the Time Difference Method. We checked the fact that the selected design factor affected starting characteristic of the Line-Start Permanent Magnet Synchronous Motor. Depend on this result we found the optimized design point by using the response optimization.

• Proceedings of the KSME Conference
• /
• 2000.11b
• /
• pp.434-440
• /
• 2000

This study is focused on the performance prediction and design of the centrifugal pump with optimum shape. Design and analysis of centrifugal pump rely on experience of designer due to many fluid mechanical and geometrical variables. In this study, a design method was developed with experimental factors and analysed the method by comparition with 2nd-order vortex panel method. Impeller is the most important component affecting the performance of the centrifugal pump. The predicted total head for three cases, of which designs were determined by this method, agrees well with a particular commercial pump. This study shows that satisfactory performance of an optimal pump shape can be obtained through the automatic design routine.

• Journal of Power Electronics
• /
• v.12 no.1
• /
• pp.104-112
• /
• 2012

In this paper a new method for the design of a simple PI controller is presented and it has been applied in the control of a Boost based PFC rectifier. The Strength Pareto evolutionary algorithm, which is based on the Pareto Optimality concept, used in Game theory literature is implemented as a multi-objective optimization approach to gain a good transient response and a high quality input current. In the proposed method, the input current harmonics and the dynamic response have been assumed as objective functions, while the PI controller's gains of the PFC rectifier (Kpi, Tpi) are design variables. The proposed algorithm generates a set of optimal gains called a Pareto Set corresponding to a Pareto Front, which is a set of optimal results for the objective functions. All of the Pareto Front points are optimum, but according to the design priority objective function, each one can be selected. Simulation and experimental results are presented to prove the superiority of the proposed design methodology over other methods.

• Corrosion Science and Technology
• /
• v.20 no.2
• /
• pp.77-84
• /
• 2021

This study aims to optimize the DL-EPR test solution for duplex stainless steel S31083 using the Taguchi design. The test solution parameters applied to the Taguchi design are H₂SO₄, NaCl, KSCN concentration, and temperature. In the experimental design, an orthogonal array of 4 levels 4 factor L₁₆(4⁴) was used. Output values for the orthogonal array were used for resolution (degree of sensitization) and selective etch (I_a) values. The optimal test solution conditions were selected by comparing the normalized S/N ratio for the two reaction properties. As a result, the H₂SO₄ and NaCl were identified as the main factors influencing the sensitivity measurement, but the delta statistics showed that the KSCN concentration and temperature had relatively low influence. The optimal condition was identified as 1.5 M H₂SO₄+0.03 M KSCN+1.5M NaCl at 30 ℃. The degree of sensitization presented a tendency to depend on the heat treatment temperature and time in the optimal test solution. This investigation confirmed the possibility of optimizing the experiment solution for the DL-EPR test of stainless steel using the Taguchi technique.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.27 no.1
• /
• pp.72-79
• /
• 2017

A full treatment of damping material is not an effective method because the damping effect is not significantly increased compared to that obtained by an effective partial damping treatment. Thus, a variety of methodologies has been considered in order to achieve an optimal damping treatment. One of the widely applied approaches is topology optimization. However, the high computational expenses can be an issue in topology optimization. A new efficient convergence criterion, reducible design variable method (RDVM), is applied to reduce computational expense in topology optimization. The idea of RDVM topology optimization is to adaptively reduce the number of design variables based on the history. The iteration repeats until the number of design variables becomes zero. The aim of this research is to adopt RDVM topology optimization into obtaining an optimal damping treatment. In order to demonstrate the effectiveness and efficiency of RDVM topology optimization, optimal damping layouts and computational expenses are compared between conventional and RDVM topology optimization.

• IE interfaces
• /
• v.11 no.3
• /
• pp.23-40
• /
• 1998

In this paper, a method to determine the optimal configuration of operating policies in an integrated-automated manufacturing system using the Taguchi method and computer simulation experiments is presented. An integrated-automated manufacturing system called direct-input-output manufacturing system(DIOMS) is described. We only consider the operational aspect of the DIOMS. Four operating policies including input sequencing control, dispatching rule for the storage/retrieval(S/R) machine, machine center-based part type selection rule, and storage assignment policy are treated as design factors. The number of machine centers, the number of part types, demand rate, processing time and the rate of each part type, vertical and horizontal speed of the S/R machine, and the size of a local buffer in the machine centers are considered as noise factors in generating various manufacturing system environment. For the performance characteristics, mean flow time and throughput are adopted. A robust design experiment with inner and outer orthogonal arrays are conducted by computer simulation, and an optimal configuration of operating policies is presented which consists of a combination of the level of each design factor. The validity of the optimal configurations is investigated by comparing their signal-to-noise ratios with those obtained with full factorial designs.

• Steel and Composite Structures
• /
• v.44 no.5
• /
• pp.603-617
• /
• 2022

Structural design, in general, is developed through trial and error technique which is guided by standards criteria and based on the intuition and experience of the engineer, a context that leads to structural over-dimensioning, with uneconomic solutions. Aiming to find the optimal design, structural optimization methods have been developed to find a balance between cost, structural safety, and material performance. These methods have become a great opportunity in the steel structural engineering domain since they have as their main purpose is weight minimization, a factor directly correlated to the real cost of the structure. Assuming an objective function of minimum weight with stress and displacement constraints provided by Brazilian standards, the present research proposes the sizing optimization and combined approach of sizing and shape optimization, through a software developed to implement the Simulated Annealing metaheuristic algorithm. Therefore, two steel plane frame layouts, each admitting four typical truss geometries, were proposed in order to expose the difference between the optimal solutions. The assessment of the optimal solutions indicates a notable weight reduction, especially in sizing and shape optimization combination, in which the quantity of design variables is increased along with the search space, improving the efficiency of the optimal solutions achieved.

• Journal of the Korean Geosynthetics Society
• /
• v.18 no.4
• /
• pp.205-214
• /
• 2019

Load and resistance factor design of mound breakwater against circular failure was developed in this study. To achieve the goal, uncertainties of parameters of soils, mound, and concrete cap were determined. Eight design cases of domestic mound breakwaters were collected and analyzed. Monte Carlo Simulation was implemented to determine the most critical slip surfaces of the design cases. Using the results of Monte Carlo Simulation, First-Order Reliability Method (FORM) was used to perform reliability analyses. Optimal load and resistance factors were calculated using the reliability analysis results and final load and resistance factors were proposed based on the calculated optimal factors.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2001.04a
• /
• pp.173-180
• /
• 2001

In this study steel box girders used as main members of a two span continuous steel bridge, are optimally designed by a Load and Resistance Factor Design method(LRFD) using an numerical optimization method. The width, height, web thickness and flange thickness of the main girder are set as design variables, and light weight design is attempted by choosing the cross-sectional area as an object function. We studied the results of steel box girders and compared with those of 1-type girders. The main program is coded with C++ and connected with optimization modul ADS. which is coded with FORTRAN.