• Journal of IKEEE
• /
• v.22 no.4
• /
• pp.1019-1024
• /
• 2018

In this paper, we suggest a combined cost function to find out the optimal operation of an envelope tracking system, and evaluated its performance with Quadrature Amplitude Modulation (QAM) waveform, with which envelope tracking coefficients for the peak drain efficiency and the bandwidth of power amplifiers are determined. Based on the classical envelope tracking theory, the operation of the supply modulator, which is a key part of the envelope tracking process, is modeled and analyzed mathematically. Then characteristics of the modulator by setting envelope shaping function as a cubic polynomial and sweeping the coefficients of this function was analyzed. By sweeping the coefficients, efficiency and bandwidth at each condition with 64-QAM signal was used to obtain optimal point of the supply modulator. Compared to the conventional shaping functions, the optimized function showed the bandwidth reduction by 12.7 percent point while the efficiency was maintained.

• Journal of the Korean Society of Combustion
• /
• v.13 no.2
• /
• pp.23-32
• /
• 2008

Gasification characteristics in the fluidized bed reactor are essential for the design of a gasification furnace to optimize the operation condition. Moisture content of the solid fuel is one of the important factors to influence directly the gasification characteristics. So it is necessary to investigate the effect of moisture content of solid fuel in partial oxidation condition. Gasification characteristics are investigated with results from thermogravimetric analyzer and lab-scale fluidized bed reactor for wood and RDF samples along with changing moisture contents. Additionally lab-scale fluidized bed reactor was run continuously and gas concentrations at the exit were measured. It is observed that the rate of reaction in partial oxidation condition is between the results from the combustion environment and from the inert condition. Moisture content in a particle slows down the heating rate of a particle. So, reaction is delayed by the moisture content. However, RDF samples those are easy to break-up don't show the effect of moisture content. The result of continuous operation condition shows that proper moisture content promotes gasification because steam from the particles helps gasification of the solid fuel. A simulation to predict the syn-gas composition was conducted by the Aspen Plus process simulator. The cold gas efficiency of the experiment was compared with results from the simulation.

• ETRI Journal
• /
• v.38 no.2
• /
• pp.244-251
• /
• 2016

In this paper, we investigate the electrical characteristics of two trench-gate-type super-barrier rectifiers (TSBRs) under different p-body implantation conditions (low and high). Also, design considerations for the TSBRs are discussed in this paper. The TSBRs' electrical properties depend strongly on their respective p-body implantation conditions. In the case of the TSBR with a low p-body implantation condition, it exhibits MOSFET-like properties, such as a low forward voltage ($V_F$) drop, high reverse leakage current, and a low peak reverse recovery current owing to a majority carrier operation. However, in the case of the TSBR with a high p-body implantation condition, it exhibits pn junction diode.like properties, such as a high $V_F$, low reverse leakage current, and high peak reverse recovery current owing to a minority carrier operation. As a result, the TSBR with a low p-body implantation condition is capable of operating as a MOSFET, and the TSBR with a high p-body implantation condition is capable of operating as either a pn junction diode or a MOSFET, but not both at the same time.

• Journal of Korean Society of Water and Wastewater
• /
• v.14 no.4
• /
• pp.311-317
• /
• 2000

The operation of flocculation process and the evaluation thereof have been mainly based on G, t and $G{\times}t$ values which are available from design guidelines and texts. However, their suggested ranges are too wide to find the optimum condition specific to a particular water treatment plant and none of the existing method can be used to evaluate and suggest the optimum operational condition. Recently, a commercially available particle counter is found to be useful in determining the flocculation process based on the particle dynamics. The optimum condition is defined as one that best suits the purpose of flocculation; the number of small particles should decrease, while that of large particles should increase. The experiments were performed at two conventional water treatment plants in Korea, one with horizontal mechanical flocculators, and another with vertical type mechanical flocculators. In this paper, experiences to evaluate the flocculation process and to suggest the optimum operation condition will be presented. Although particle counting method is found to be beneficial compared to any other existing methods, the optimum condition is very much site-specific and should be evaluated at each water treatment plant for different conditions.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.5 no.4
• /
• pp.59-64
• /
• 2006

High Speed Machining(HSM) reduces machining time and improves surface accuracy because of the high cutting speed and feedrate. Development of HSM makes it allowable to machine difficult-to-cut material and use small-size-endmill. It is however limited to cutting condition and tool material. In the machining operation, it is important to check main parameter of tool life and select optimal cutting condition because tool breakage can interrupt progression of operation. In this study, cutting parameters are determined to 3 factors and 3 levels which are a spindle speed, a feedrate and a width of cut. Experiment is designed to orthogonal array table for L9 with 3 outer array using Taguchi method. Also, it is proposed to inspect significance of the optimal factors and levels by ANOVA using average of SN ratio for tool life. Finally, estimated value of SN ratio in the optimal cutting condition is compared with measured one in the floor shop and reduction of loss is predicted.

• The Korean Journal of Rehabilitation Nursing
• /
• v.14 no.2
• /
• pp.136-144
• /
• 2011

Purpose: A purpose of this study was to identify the effects of cold water gargling on thirst, oral cavity condition and sore throat in orthopedics surgery patients who underwent general anesthesia. Methods: Pretest-posttest non-synchronized design with a nonequivalent control group was used. A total of 52 participants were conveniently selected and assigned to each group. The experimental group gargled hourly with cold water for 8 hours after operation. The control group received wet gauze as needed. We compared the thirst, oral cavity condition and sore throat at 0, 2, 4 and 8 hours after operation. Results: The score of thirst and oral cavity condition was lower in the experimental group than in the control group. However, there was no significant differences in the levels of sore throat between the experimental and control group. Conclusion: These findings suggest that cold water gargling can be a useful nursing intervention for alleviating thirst and improving oral condition for patients with orthopedic surgery after general anesthesia.

• Journal of the Korean Society for Railway
• /
• v.9 no.1 s.32
• /
• pp.29-35
• /
• 2006

Trains in LRT(Light Railway Transit) system usually have shorter car length than metro's because of their smaller passensers demand. Therefore it is very likely that the load condition of LRT system in abnormal operation, in case of which trains are in close proximity by system broke or train rescue works, could be worse rather than in normal operation, in spite of rare probability of abnormal operation. In this study, the target reliability indexes of several abnormal operations are estimated in accordance with the occurrence probabilities of each abnormal operation case and the reliability index of normal operation presented by the specification. From the indexes, load factors for the abnormal operation cases are estimated and the safety evaluation is performed for Yong-in LRT project.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.2
• /
• pp.196-204
• /
• 1996

This paper presents a new scheduling algorithm, which is the most improtant subtask in the high level synthesis. The proposed algorithm performs scheduling in consideration of resource sharing concept based on characteristics of conditionsla bransches in the intermediate data structure. CDFG (control data flow graph) generated by a VHDL analyzer. This algorithm constructs a conditon graph based on time frame of each operation using both the ASAP and the ALAP scheduling algorithm. The conditon priority is obtained from the condition graph constructed from each conditional brance. The determined condition priority implies the sequential order of transforming the CDFG with conditonal branches into the CDFG without conditional branches. To minimize resource cost, the CDFG with conditional branches are transformed into the CDFG without conditonal brancehs according to the condition priority. Considering the data dependency, the hardware constraints, and the data execution time constraints, each operation in the transformed CDFG is assigned ot control steps. Such assigning of unscheduled operations into contorl steps implies the performance of the scheduling in the consecutive movement of operations. The effectiveness of this algorithm is hsown by the experiment for the benchmark circuits.

• 제어로봇시스템학회:학술대회논문집
• /
• 1990.10a
• /
• pp.170-174
• /
• 1990

The information with regard to the working range of lathe, cutting tool, cutting condition is managed as Database system for turning operation as one part of CAM system. Data with regard to the working range of lathe, cutting tool, cutting condition are stored by the DBMS(Data Base Management System) and can be added, modified, deleted and retrieved for realtime usages. Data stored in Database system are searched to select the most proper cutting tool and cutting condition with the input data fed from the design stage. Codes in regards to tool shape are displayed on graphic mode for easy selection for user and thus presents a good decision support for tool selection. The system developed in this work is operated by the pull down menu on the IBM PC/AT personal computer, or compatible series.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.3140-3141
• /
• 2008

The output power efficiency of the fuel cell system depends on the demanded current, stack temperature, air excess ratio, hydrogen excess ratio and inlet air humidity. Thus, it is necessary to determine the optimal operation condition for maximum power efficiency. In this paper, we developed a dynamic model of fuel cell system which contains mass flow model, diffusivity gas layer model, membrane hydration and electrochemistry model. In order to determine the maximum output power and minimum use of hydrogen in a certain power condition, response surface methodology (RSM) optimization based on the proposed PEMFC stack model is presented. The results provide an effective method to optimize the operation condition under varied situations.