• 대한기계학회논문집B
• /
• 제29권12호
• /
• pp.1360-1368
• /
• 2005

This study investigates the characteristics of spray, such as evaporation rate and spray trajectory, for a 4-hole injector which is applied to a 4-valve motorcycle gasoline engine. Three dimensional, unsteady, compressible flow and spray within the intake-port and cylinder have been simulated using the VECTIS code. Spray characteristics were investigated at 6000 rpm engine speed. Furthermore, we visualized fuel behavior in the intake-port using a CCD camera synchronized with a stroboscope in order to compare with the analytical results. Boundary and intial conditions were employed by complete 1-D simulation of the engine using the WAVE code. Fuel was injected into the intake-port at two time intervals relative to the position of the intake valves so that the spray arrived when the valves were closed and fully open. The results showed that the trajectory of the spray was directed towards the lower wall of the port with injection against the closed valves. With open valve injection, a large portion of the fuel was lifted by the co-flowing air towards the upper half of the port and this was confirmed by simulation and visualization.

• 상하수도학회지
• /
• 제25권6호
• /
• pp.869-875
• /
• 2011

Ministry of Environment has been promoting BTL business of the sewer rehabilitation which continues from 2005 up to now. Sewer rehabilitation is classified into three parts : wastewater pipe rehabilitation, rainwater pipe rehabilitation and drainage equipment rehabilitation. Drainage equipment rehabilitation is that drainage pipe connects wastewater pipe directly without water-purifier. In the drainage equipment construction, it is inevitable to have the damage of ground structures(wall, gate and U drain, etc) when an open excavation method is used. Therefore it is necessary to develop non-excavation method to connect drainage pipe and wastewater pipe like jacking method to avoid the damage of ground structure. This paper has conducted an analysis of the non-excavation method using a boring machine attached to backhoe, which is issued the verification certificate of environmental technology according to the Development of and Support for Environmental Technology Act, article.7. The index set in this analysis was sectionalized to the condition of construction, the grade of drainage pipe, the size of excavated hole, the amount of waste cement concrete and asphalt concrete and the benefit effect compared to open excavation method.

• Korean Chemical Engineering Research
• /
• 제48권5호
• /
• pp.654-659
• /
• 2010

박막형 유기 태양전지의 효율 향상을 위하여 정공 수송층인 CuPc 층에 p형 유기 반도체인 rubrene을 함량 별로 도핑하여 ITO/PEDOT:PSS/CuPc: rubrene/CuPc:C60(blending ratio 1:1)/C60/BCP/Al의 이종접합구조를 가지는 p-i-n형 유기 박막형 태양전지 소자를 제조한 후, 유기 태양전지의 전류 밀도-전압(J-V) 특성, 단락 전류($J_{sc}$), 개방 전압($V_{oc}$), 충진 인자(fill factor:FF), 에너지 전환 효율(${\eta}_e$) 등을 측정하고 계산하여 성능 평가를 수행 하였다. 정공 수송층으로 사용된 CuPc 층에 rubrene을 도핑함으로써 에너지 흡수 스펙트럼에서 흡수 강도가 감소하였다. 그러나 CuPc 보다 큰 밴드갭을 가지며 높은 정공 이동도를 가지는 결정성 rubrene의 도핑에 의해 제조된 p-i-n형 유기 박막 태양전지의 성능은 향상 되는 것으로 확인되었다. 제조된 유기 태양전지의 에너지 전환 효율(${\eta}_e$)은 1.41%로 실리콘 태양전지와 비교해서 아직도 성능 향상을 위한 많은 노력이 필요함을 보여 준다.

• 설비공학논문집
• /
• 제14권12호
• /
• pp.1039-1046
• /
• 2002

To investigate the characteristics of orifice as an expansion devices, the experimental apparatus was made and experiments are being peformed using R22 and R290. The main idea of this control method of refrigerant flow rate with coupled orifices is to control the ON/OFF state of T and Ball type orifice corresponding to the subdivided region of thermal load. When system requires minimum thermal load, both T and Ball type orifices are closed, but refrigerant can flow through small hole of T type orifice. In regular thermal load, when ball type orifice is closed, T type orifice is opened and mass flow rate increase more than OFF state of T type orifice, due to large diameter. In maximum thermal load, both T and Ball type orifices are open and the much refrigerant can flow. The flow characteristics on T type orifice and parallel-combined orifice are obtained in the subdivided region of thermal load.

• 지질공학
• /
• 제28권1호
• /
• pp.1-9
• /
• 2018

We propose a borehole test technique to estimate permeability of rocks in borehole. The borehole tests are hydraulic injection tests such as leak-off test and hydraulic fracturing tests, which are originally conducted for stress or casing integrity assessment and not for permeability measurement. We use one-dimensional radial diffusion equation to interpret fluid injection test results in terms of permeability. We apply this technique to a leak-off test conducted at a depth of 700 m in a wellbore, where rock formation is mudstone. The estimated permeability is at an order of $10^{-16}m^2$, which is somewhat high but within the range reported for mudstones previously. Quantitative rick assessment suggests that an accurate measurement of open hole section length is important to improve reliability of results. More data may be needed to ensure the reliability of this technique. If validated, however, this technique can provide cost-effective estimation of in situ permeability without conducting independent permeability tests in borehole.

• 소성∙가공
• /
• 제20권2호
• /
• pp.93-98
• /
• 2011

Electroforming is a kind of metal molding technology. After gilding on the possession object(conductivity, nonconductivity) separate it with possession object and produce a part or duplicate. This process has an excellent ability of duplicating detailed figure. To simplify the manufacturing process of a rotary screen, this study was adopted electroforming technology and produced silicon rubber mandrel. Furthermore, to indicate the optimal condition for the acquisition of high-qualified rotary screen product, the experiment was executed with pH, time, sulfamate nickel solution according to density which were the main factors to decide the condition, then compared it with the product made by original "S" company in Holland. As a result, the figure of hole was more obvious and correct. Also the open size increased by more than 2-3%.

• 한국표면공학회지
• /
• 제34권3호
• /
• pp.187-194
• /
• 2001

Galvalume sheet steel was developed recently, and is used widely in several fields. It has and had a good corrosion resistance in open atmosphere, but it has week corrosion resistance in the ambient surroundings of an airtight packing. Therefore, black patina was synthesized on the surface of Galvalume sheet steel. Corrosion by moisture on a Galvalume surface begins from edge of a droplet and proceeds to the center of droplet. It begins mainly on the interdendritic structure instead of dendritic structure. This suggests that corrosion by moisture occurs on the Zn shrinkage hole from rapid air cooling. In addition, the initial corrosion occurs by the local cell and continues by the oxygen concentration cell.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2001년도 유체기계 연구개발 발표회 논문집
• /
• pp.419-424
• /
• 2001

TCV(Temperature control valve by pressure compensation) controls temperature constantly, when it is sending steam or high temperature water to heating device of heat exchanger. For designing TCV, the ratio of piston and hole diameters is one of the important design parameters. Numerical analysis is carried out to elucidate the flow characteristics in the TCV with different port areas of cold and hot waters, using the k-$\epsilon$ turbulence model and Cartesian cut-cell method. Numerical results show that the exit flow rate is mainly affected by pressure distribution in the piston.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2000년도 추계종합학술대회 논문집(2)
• /
• pp.25-28
• /
• 2000

In this paper, three types of organic electroluminescent devices(OELD) were fabricated on mechanically flexible plastic substrate by using vacuum deposition method. The devices consist of a hole transporting material such as TPD, a light-emitting material such as Alq$\sub$3/ and an electron transporting material, blocking material such as PBD. Electrical and optical properties of these OELDs were measured. This paper shows that organic small molecules based on OELD can be successfully deposited on a flexible plastic substrate. This points open the potential for low cost mass production of flexib]e displays, including roll to roll processing.

• 아시안잔디학회지
• /
• 제13권3호
• /
• pp.171-176
• /
• 1999

Chrysanthemum showed worse grow of wilt to death during summer at the field which is Allium fistulosum (welsh onion) plants had been cultivated. This study was carried out to analysis of activative inhibitors of chrysanthemum from root exudate of Allium fistulosum. Bioassay experiments with welsh onion root exudate were conducted and the biologically active compounds were determined. The results were obtained as follows. The root exudate of welsh onion inhibited root and hypocotyl growth of chrysanthemum and lettuce at low concentration(10ppm). The inhibitory effects was higher in closed bottom box but with drain hole than in open bottom box plot. The inhibitory substance contained in root exudate was analysed as vanillic acid. This phenolic acid was also detected in stem-leaf and root of welsh onion.