• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2000.11c
• /
• pp.749-756
• /
• 2000

Chemical application, one of the most important crop management processes happened to cause spray drift, that would threaten farmers in field as well as dwellers in rural region. Spray drift was affected by micro-meteorological parameters. In Korea, a boom sprayer was introduced but good effects of a boom sprayer was not evaluated. A study to evaluate short distance drift characteristics of a boom sprayer in paddy fields has been undergoing and determining wind characteristics in paddy field was the main purpose of this paper. Micro-meteorological information has been pre-requisite information for evaluating drift in both long and short distances or in both theoretical and experimental ways. Wind velocity, Reynolds stresses, turbulence intensity, skewness, kurtosis etc. were evaluated with height from the ground using a 2-dimensional probe and a hot wire anemometer system.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.11
• /
• pp.3046-3056
• /
• 1994

To design and develop a turbocharged engine, it needs that many studies must be preceded about the characteristics of engine performance and thermal flow. To accomplish this purpose, turbocharger was equipped to 1.3 liter naturally aspirated gasoline engine. The temperature probe of plate type was designed and it was installed into the combustion chamber wall to measure unsteady temperature. The unsteady heat flux at combustion chamber wall was evaluated using one dimensional unsteady conduction equation with the wall temperature and temperature gradient.

• 유체기계공업학회:학술대회논문집
• /
• 2006.08a
• /
• pp.161-164
• /
• 2006

Three-dimensional flow and aerodynamic loss in the tip-leakage flow region of a high-turning first-stage turbine rotor blade with a squealer tip have been measured with a straight miniature five-hole probe for the tip gap-to-chord ratio, h/e, of 2,0%. This squealer tip has a indent-to-chord ratio, $h_{st}/c$, of 5.5%. The results are compared with those for a plane tip ($h_{st}/c\;=\;0.0%$). The squealer tip tends to reduce the mass flow through the tip gap and to suppress the development of the tip-leakage vortex. Therefore, it delivers lower aerodynamic loss in the near-tip region than the plane tip does. At the mid-span, however, the aerodynamic loss has nearly the same value for the two different tips.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2005.06a
• /
• pp.255-263
• /
• 2005

Migration experiments of THO and 237Np have performed through a sampled granite core in Chemlab2 probe at the Aspo hard Rock laboratory. The elution curves of THO were analysed to determine hydraulic properties such as the extent of dispersion effect according to flow rates. The retardation phenomena of the solutes were observed and described with elution curves and migration plumes. After migration test, the rock core was opened, and the remaining radioactivities on the rock fracture surfaces were measured. The transport process was simulated with a two-dimensional channel model. The mass transport process was described with three types of basic processes ; advection, sorption and matrix diffusion. By the combination of these processes, effects of each process on transport were described in terms of elution curves and migration plumes. By comparing the simulation results to the experimental one, it was possible to analyse the retardation effect quantitatively.

• Proceedings of the Korea Crystallographic Association Conference
• /
• 2002.11a
• /
• pp.37-37
• /
• 2002

반도체 소자의 집적도는 지난 수십년간 끊임없이 증가해 왔다. 이러한 추세가 계속 된다면 앞으로 수년 이내에 100 nm 이하의 선폭을 갖는 집적회로가 출현하게 될 것이다. 수-수십나노 미터 크기의 구조가 이와같이 제품에 실제로 응용되려면 수 나노미터의 길이에 대한 표준 측정 기술이 확보되어야 하고 이 측정 기술을 서로 비교 평가 할 수 있는 표준 물질이 필요하다. 본 연구에서는 표준 물질로 사용될 수 있는 1차원 나노 구조를 제작하였다. 제작된 1차원 나노 구조는 선폭이 90 nm인 네모난 산과 네모난 우물들이 반복적으로 나타나는 형태를 갖는다. 나노 구조가 제작된 총영역은 0.1 ㎜ × 0.1 ㎜의 정사각형 영역이다. 1차원 나노 구조는 전자빔 석판 기술을 이용하여 제작하였다. 균일한 구조를 만들기 위해 전자 빔의 도즈량 최적화, 전자 빔의 비대칭성의 영향 최소화, 에칭 공정 변수 최적화 등 공정 조건을 선별하는 연구를 하였다. 본 연구에서 제작된 1차원 나노구조는 전자현미경의 배율 보정, Scanning Probe Microscope의 이미지 보정 등에 사용될 수 있을 것이다.

• Journal of Electrical Engineering and Technology
• /
• v.7 no.2
• /
• pp.225-229
• /
• 2012

This paper proposes a reduced-scale simulator that can replace numerical analytic methods for the estimation of potential distribution caused by ground faults in various grounding systems. The simulator consists of a hemispherical electrolytic tank, a three-dimensional potential probe, a grounding electrode, and a data acquisition module. The potential distribution is measured using a potentiometer with a position-tracing function when a test current flows to the grounding electrode. Using the simulator, we could clearly analyze the potential distribution for a reduced- scale model by one-eightieth of the buried depth and length of the grounding rod and grounding grid. Once both the shape of the grounding electrode and the fault current are known, the actual potential distribution can be estimated.

• Journal of the Society of Naval Architects of Korea
• /
• v.34 no.2
• /
• pp.11-19
• /
• 1997

The new definition of calibration coefficients is proposed for a five-hole Pitot tube. Two-angle chart calibration other than one-angle variation is considered to improve the accuracy in the measurement of the three-dimensional velocity fields. Several sets of correlation coefficients are introduced for different shapes of the probe tip. The calibration method with one-angle variation is compared with the new two-angle chart calibration method and the improvement of the present method is clearly shown.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.85-85
• /
• 2010

Graphene, the building block of graphite, is one of the most promising materials due to their fascinating electronic transport properties. The pseudo-two-dimensional sp2 bonding in graphene layers yields one of the most effective solid lubricants. In this poster, we present the correlation between electrical and nanomechanical properties of graphene layer grown on Cu/Ni substrate with CVD (Chemical Vapor Deposition) method. The electrical (current and conductance) and nanomechanical (adhesion and friction) properties have been investigated by the combined apparatus of friction force microscopy/conductive probe atomic force microscopy (AFM). The experiment was carried out in a RHK AFM operating in ultrahigh vacuum using cantilevers with a conductive TiN coating. The current was measured as a function of the applied load between the AFM tip and the graphene layer. The contact area has been obtained with the continuum mechanical models. We will discuss the influence of mechanical deformation on the electrical transport mechanism on graphene layers.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.4
• /
• pp.84-91
• /
• 2005

We measured the pitch of one-dimensional (ID) grating specimens using a metrological atomic force microscope (M-AFM). The ID grating specimens a.e often used as a magnification standard in nano-metrology, such as scanning probe microscopy (SPM) and scanning electron microscopy (SEM). Thus, we need to certify the pitch of grating specimens fur the meter-traceability in nano-metrology. To this end, an M-AFM was setup at KRISS. The M-AFM consists of a commercial AFM head module, a two-axis flexure hinge type nanoscanner with built-in capacitive sensors, and a two-axis heterodyne interferometer to establish the meter-traceability directly. Two kinds of ID grating specimens, each with the nominal pitch of 288 nm and 700 nm, were measured. The uncertainty in pitch measurement was evaluated according to Guide to the Expression of Uncertainty in Measurement. The pitch was calculated from 9 line scan profiles obtained at different positions with 100 ㎛ scan range. The expanded uncertainties (k = 2) in pitch measurement were 0.10 nm and 0.30 nm for the specimens with the nominal pitch of 288 nm and 700 nm. The measured pitch values were compared with those obtained using an optical diffractometer, and agreed within the range of the expanded uncertainty of pitch measurement. We also discussed the effect of averaging in the measurement of mean pitch using M-AFM and main components of uncertainty.

• Korean Journal of Materials Research
• /
• v.24 no.10
• /
• pp.543-549
• /
• 2014

A zinc oxide (ZnO) hybrid structure was successfully fabricated on a glass substrate by metal organic chemical vapor deposition (MOCVD). In-situ growth of a multi-dimensional ZnO hybrid structure was achieved by adjusting the growth temperature to determine the morphologies of either film or nanorods without any catalysts such as Au, Cu, Co, or Sn. The ZnO hybrid structure was composed of one-dimensional (1D) nanorods grown continuously on the two-dimensional (2D) ZnO film. The ZnO film of 2D mode was grown at a relatively low temperature, whereas the ZnO nanorods of 1D mode were grown at a higher temperature. The change of the morphologies of these materials led to improvements of the electrical and optical properties. The ZnO hybrid structure was characterized using various analytical tools. Scanning electron microscopy (SEM) was used to determine the surface morphology of the nanorods, which had grown well on the thin film. The structural characteristics of the polycrystalline ZnO hybrid grown on amorphous glass substrate were investigated by X-ray diffraction (XRD). Hall-effect measurement and a four-point probe were used to characterize the electrical properties. The hybrid structure was shown to be very effective at improving the electrical and the optical properties, decreasing the sheet resistance and the reflectance, and increasing the transmittance via refractive index (RI) engineering. The ZnO hybrid structure grown by MOCVD is very promising for opto-electronic devices as Photoconductive UV Detectors, anti-reflection coatings (ARC), and transparent conductive oxides (TCO).