• 한국재료학회지
• /
• 제33권12호
• /
• pp.537-549
• /
• 2023

The sintering shrinkage behaviors of low temperature cofired ceramics (LTCC) and resistors were compared using commercial LTCC and thick-film resistor pastes, and factors influencing the camber of cofired resistor/LTCC bi-layers were also investigated. The onset of sintering shrinkage of the resistor occurred earlier than that of LTCC in all resistors, but the end of sintering shrinkage of the resistor occurred earlier or later than that of LTCC depending on the composition of the resistor. The sintering shrinkage end temperature and the sintering shrinkage temperature interval of the resistor increased as the RuO₂/glass volume ratio of the resistor increased. The camber of cofired resistor/LTCC bi-layers was obtained using three different methods, all of which showed nearly identical trends. The camber of cofired resistor/LTCC bi-layers was not affected by either the difference in linear shrinkage strain after sintering between LTCC and resistors or the similarity of sintering shrinkage temperature ranges of LTCC and resistors. However, it was strongly affected by the RuO₂/glass volume ratio of the resistor. The content of Ag and Pd had no effect on the sintering shrinkage end temperature or sintering shrinkage temperature interval of the resistor, or on the camber of cofired resistor/LTCC bi-layers.

• 한국세라믹학회지
• /
• 제51권4호
• /
• pp.344-349
• /
• 2014

$RuO_2$-based high frequency thick-film resistor paste was printed at the speed of 10, 100, 300 mm/sec on the AlN substrate, and then sintered at between 750 and $900^{\circ}C$. The sintered thick films were characterized in terms of printing and sintering conditions. With increasing printing speed, the thickness and roughness of sintered film increased. The resistance of the thick film resistor was reduced by increasing the printing speed from 10 to 100 mm/sec, but did not significantly change at 300 mm/sec speed. With increasing sintering temperature, the surface roughness and thickness of sintered resistor film decreased. The reduction rate was large in case of fast printed resistor. The resistance of the resistor increased up to $800^{\circ}C$ with sintering temperature, but again decreased at the higher sintering temperature.

• 대한전자공학회논문지SD
• /
• 제45권4호
• /
• pp.72-77
• /
• 2008

본 논문에서는 Embedded resistor 적용을 위한 오개닉 기판 위에 캐버티(Cavity) 공정에 의해서 형성된 균일한 두께를 갖는 저항체의 제조 방법과 저항편차에 대해서 조사했다. 기존의 스크린 프린팅에 의해서 발생하는 PCB의 위치에 따른 저항값의 편차를 개선하기 위하여 캐버티 공정을 소개했다. 원하는 모양과 부피를 갖는 저항은 스크린 프린팅과 페이스트를 이용하여 cavity 공정에 의해 정확하게 형성되어 졌다. 이 방법은 PCB의 생산 공정시간을 줄일 수 있고, 스크린 프린팅의 정밀도에 의한 큰 영향 없이 빠르게 공정 조건을 배치할 수 있으므로써 생산량을 개선시킬 수 있다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.2
• /
• pp.764-767
• /
• 2003

Nowadays, the study on the ceramic components and modules using LTCC is being peformed and on the passives included in modules is being done also. Especillay frequency dependent components like capacitor and inductor are studied by many groups, but the behavior of embedded resistor in MCM-C module are not studied vigorously. The characteristics of embedded resistor in modules is different from that of resistor alone. In our research, behavior of embedded resistor is examined in the variation of position and geometrical parameters.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.2
• /
• pp.599-602
• /
• 2004

Nowadays, the study on the ceramic components and modules using LTCC is being peformed and on the passives included in modules is being done also. Especillay frequency dependent components like capacitor and inductor are studied by many groups, but the behavior of embedded resistor in MCM-C module are not studied vigorously. The characteristics of embedded resistor in modules is different from that of resistor alone. In our research, behavior of embedded resistor is examined in the variation of position and geometrical parameters.

• 한국전기전자재료학회논문지
• /
• 제24권3호
• /
• pp.200-207
• /
• 2011

Abstract: The effect of lead free glass frit compositions on the properties of thick film conductor and resistor pastes were investigated. Two types lead free frits, HBF-A(without $Bi_2O_3$) and HBF-B(with $Bi_2O_3$) were made from $SiO_2$, $B_2O_3$, $Al_2O_3$, CaO, MgO, $Na_2O$, $K_2O$, ZnO, MnO, $ZrO_2$, $Bi_2O_3$. And Ag based conductor pastes and $RuO_2$ based resistor paste were prepared by mixed with these frits and functional phase(Ag and $RuO_2$), and organic vehicle. The properties of thick film conductor and resistor sintered at $850^{\circ}C$ were studied after printing on $Al_2O_3$ substrate. The morphology of the sintered films surface were SEM and EDS were carried out to analysis the chemical composition on resistor surface and state of Ru atom in frit matrix.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 춘계학술대회 논문집 센서 박막재료 반도체재료 기술교육
• /
• pp.82-85
• /
• 2002

In recent years, the tantalum nitride(TaN) thin-film has been developed for the electronic resistor and capacitor. In this papers, this study presents the surface profile and sheet-resistance property relationship of reactive-sputtered TaN thin film resistor processed by buffer of Ti and Cr on alumina substrate. The TCR properties of the TaN films were discussed in terms of reactive gas ratio, ratio of nitrogen, crystallization and thin films surface morphology due to annealing temperature. It is clear that the TaN thin-films resistor electrical properties are low TCR related with it's buffer layer condition. Ti buffer layer thin film resistor having a good thermal stability and lower TCR properties then Cr buffer expected for the application to the dielectric material of passive component.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.421-421
• /
• 2008

Generally, the polymer thick-film resistors for embedded organic or hybrid substrate are patterned by screen printing so that the accuracy of resistor pattern is not good and the tolerance of resistance is too high(${\pm}$20~30%). To reform these demerits, a method using Fodel$^{(R)}$ technology, which is the patterning method using a photosensitive resin to be developable by aqueous alkali-solution as a base polymer for thick-film pastes, was recently incorporated for the patterning of thermosetting thick-film resistor paste. Alkali-solution developable photosensitive resin system has a merit that the precise patterns can be obtained by UV exposure and aqueous development, so the essential point is to get the composition similar to PSR(photo solder resist) used for PCB process. In present research, we made the photopatternable resistor pastes using 8 kinds of epoxy acrylates and a conductive carbonblack (CDX-7055 Ultra), evaluated their developing performance, and then measured the resistance after final curing. To become developable by alkali-solution, epoxy acrylate oligomers with carboxyl group were prepared. Test coupons were fabricated by patterning copper foil on FR-4 CCL board, plating Ni/Au on the patterned copper electrode, applying the resistor paste on the board, exposing the applied paste to UV through Cr mask with resistor patterns, developing the exposed paste with aqueous alkali-solution (1wt% $Na_2CO_3$), drying the patterned paste at $80^{\circ}C$ oven, and then curing it at $200^{\circ}C$ during 1 hour. As a result, some test compositions couldn't be developed according to the kind of oligomer and, in the developed compositions, the measured resistance showed different results depending on the paste compositions though they had the same amount of carbonblack.

• 전기의세계
• /
• 제22권4호
• /
• pp.7-10
• /
• 1973

The characteristics of all the instruments and materials used in atomic industry is changed due to radiation damages by the effects of radiation activities. In this study, when the Carbon Resistor, main element of electrical circuits, is irradiated by Gamma-Ray, variations in its electrical properties have been investigated. The following results are obtained: 1) The resistance value in Carbon Resistor is exponentially increased as the quantity of irradiation by Gamma-Ray is increased, but in case of more than 10$^{6}$ R/hr. of quantity of irradiation it has saturated-state value. 2) The rate of change inrestistance value has been independent on the intensity of Gamma-Ray source when Carbon Resistor is irradiated in the same quantity of irradiation. 3) The resistance value in irradiated Carbon Resistor has not been varied with elapse of time. 4) The more the distance from the Carbon Resistor to the Gamma-Ray source the more greatly the resistance value is decreased and that it has been shown that the more quantity of irradiation by Gamma-Ray, the greater the rate of decrease in resistance value. Through the above results it has been concluded that the measurement values obtained by the high-precision instruments in the radiation field have to be corrected with proper consideration to radiation damages.

• 한국전기전자재료학회논문지
• /
• 제35권3호
• /
• pp.269-274
• /
• 2022

We prepared carbon nanotube (CNT) paper by a vacuum filtration method for the use of a chip-typed resistor as a precision passive device with a constant resistance. Hybrid resistor composed of the CNT resistor with a negative temperature coefficient of resistance (T.C.R) and a metal alloy resistor with a positive T.C.R could lead to a constant resistance, because the resistance increase owing to the temperature increase at the metal alloy and decrease at the CNT could counterbalance each other. The constant resistance for the precision passive devices should be maintained even when a heat was generated by a current flow resulting in resistance change. Performance reliabilities of the CNT resistor for the precision passive device applications such as electrical load limit, environmental load limit, and life limit specified in IEC 60115-1 must be ensured. In this study, therefore, the rated power determination and T.C.R tests of the CNT paper were conducted. -900~-700 ppm/℃ of TCR, 0.1~0.2 A of the carrying current capacity, and 0.0625~0.125 W of the rated power limit were obtained from the CNT paper. Consequently, we confirmed that the application of CNT materials for the precision hybrid passive devices with a metal alloy could result in a better performance reliability with a zero tolerance.