• Korean Journal of Materials Research
• /
• v.9 no.10
• /
• pp.951-955
• /
• 1999

Two-phase Al-21Ti-23Cr alloy containing 20 vol.% $\textrm{Cr}_{2}\textrm{Al}$ as a second phase in the $Ll_2$ matrix is located in the two- phase region of the Al- Ti- Cr phase diagram at $1150^{\circ}C$, while in the three-phase region at $1000^{\circ}C$. Based on this result, the mechanical properties of the A1-21Ti-23Cr alloy were enhanced through the refined precipitation of the third phase in the $Ll_2$ matrix by aging the alloy below $1000^{\circ}C$. It was observed that a several ,m of the third phase precipitated in the $Ll_2$ matrix through aging at $800^{\circ}C$ and $1000^{\circ}C$, but the precipitation was not observed below $600^{\circ}C$. Furthermore, the third phase was more finely precipitated at $800^{\circ}C$ than at $1000^{\circ}C$. Although the third phase precipitated at $800^{\circ}C$ and at $1000^{\circ}C$, the compressive yield strength increased rapidly at $800^{\circ}C$ only. This is probably attributable to the refined precipitation of the third phase in the $Ll_2$ matrix. It is expected that the precipitation of the third phase. which was confirmed to be the TiAlCr phase, improves the mechanical properties by preventing crack propagation in the $Ll_2$ matrix.

• Korean journal of applied entomology
• /
• v.22 no.4 s.57
• /
• pp.300-306
• /
• 1983

Effect on blast lesion development was investigated in rice cultivar Milyang 23 and Jinheung using two races of Pyricularia oryzae compatible or incompatible to each of two rice cultivars. Discase lesions were measured in rice when inoculated with inoculum mixed with compatible and incompatible races, inoculated with a compatible race following with an incompatible race and vice versa. Lesions were smaller when rice was incoulated with an incompatible race and then inoculated with a compatible race than those inoculated in the reverse way both at the inoculated site and at 3cm-upper part from inoculated spot. The results suggested that induced resistance might play a role in suppression of lesion development although such an effect appeared to be influenced by heavy application of nitrogen fertilizer.

• Korean journal of applied entomology
• /
• v.47 no.2
• /
• pp.155-162
• /
• 2008

The Welsh onion beet armyworm, Spodoptera exigua (Hubner), has attacked Welsh onion and is now the most important pest of Welsh onion in southwestern Korea. The beet armyworm has a wide host range, occurring as a serious pest of vegetable and fields. The relatively high abundance of beet armyworm has stimulated frequent application of insecticides to foliage. Insecticide resistance is a major problem in management of this insect. Accordingly, pesticide application for the control of beet armyworm was tried in both the open field and in laboratory, using 4 synthetic compounds such as metaflumizone and chlorfenapyr, indoxacarb, flufenoxuron, emamectin benzoate. In the laboratory, each developmental stages from eggs, larva to pupa was tested against 4 insecticides. Against the eggs of welsh onion beet armyworm, there was no significantly different with each other. These tested chemicals no killing effect to eggs. However, the population of 1st larva hatched from eggs were reduced because they eaten the egg shell with residual insecticides. The tested insecticides were taken very high mortalities to 1st to 3rd larva of Welsh onion beet armyworm. Otherwise, there were decreased the death rate from 4th to 6th larva. On the other hand, their value of control effects were relatively good against Welsh onion beet armyworms in the field between 87.2 and 90.5% on 10 days after insecticide application.

• Korean Journal of Plant Resources
• /
• v.30 no.4
• /
• pp.475-480
• /
• 2017

A new Gomchwi cultivar 'Damogy ' was bred by crossing between Gomchwi (Ligularia fischeri (Ledeb.) Turcz.) and Handaeri-gomchwi (Ligularia fischeri var. spiciformis Nakai). The selection and investigation of growth and yield characteristics were conducted from 2006 to 2011 in field and greenhouse of Highland Agriculture Research Institute, NICS, Rural Development Administration, Korea. On a newly developed cultivar 'Damogy', Color of petiole ear was purple, petiole trichome was exist, light of leaf back was not exist, and density of leaf vein was degree 4. Plant height, leaf length, leaf width and petiole length were 45.9, 16.9, 21.1 and 29.0 cm, respectively in the $3^{rd}$ year in growth characteristics. Plant size was also higher than that of Gondalbi. Bolting and flowering time were Aug. $23^{th}$ and Sept. $10^{th}$, respectively. In contrast, Gondalbi showed quite earlier bolting time more than 38 days compared with 'Damogy' and consequently earlier flowering time more than 26 day. 'Damogy' showed similar leaf number (129) per plant compared to 'Gondalbi' (130). Furthermore, yield was higher 'Damogy' (1,889 g/plant) than in 'Gondalbi' (798 g/plant). 'Damogy' showed higher leaf thickness (0.71 mm) than 'Gonalbi' (0.46 mm), and consequently showed more hardness in leaf characteristics ($28.3kg/cm^2$) compared with 'Gondalbi' ($23.0kg/cm^2$). 'Damogy' showed higher resistance in the susceptibility of powdery mildew disease compared to 'Gondalbi'. 'Damogy' variety was registered plant variety protection right as a No. 89 on December 2015.

• Korean journal of applied entomology
• /
• v.14 no.3 s.24
• /
• pp.147-153
• /
• 1975

During 1973 a field experiment was carried out to evaluate effectiveness of the root zone application of insecticides in medical gelatin capsules for control of several rice insect pests and dwarf virus disease. At three days after transplanting the capsules were pushed by hand about 2.5cm into the soil, near roots of Tongil rice plants. At the given day intervals number of leaf-and plant-hoppers on the hills were recorded by direct count, and dead hearts and white heads by stem borers and dwarf virus infected hills were observed in the experiment plots. Finally grain yields were measured. The percentages of dead hearts and white heads in all the plots were too low for evaluating the effectiveness of insecticides against the striped rice borers. Carbofuran of the insecticides tested was relatively effective against green rice leafhopper (Nephotettixcincticeps) and small brown planthopper (Laodelphax striatellus), although small number of insects on the hills were recorded. Relatively small number of white-backed planthopper (Sogatella furcifera) was occured in the BPMC and Diazinon treated plots. BPMC and Carbofuran were highly effective against the brown planthopper (Nilaparvata lugens) to 80 days after treatment. Incidence of dwarf virus disease was least in the plots of Carbofuran treatment. The highest grain yield was recorded in the plots treated with Carbofuran, and it seemed to be related with good protection from the dwarf virus disease and leaf-and plant-hoppers.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.6
• /
• pp.1-6
• /
• 2011

A transparent oxide thin film transistors (Transparent Oxide-TFT) have been fabricated by RF magnetron sputtering at room temperature using amorphous indium zinc oxide (a-IZO) as both of active channel and source/drain, gate electrodes and co-sputtered $HfO_2-Al_2O_3$ (HfAIO) as gate dielectric. In spite of its high dielectric constant > 20), $HfO_2$ has some drawbacks including high leakage current and rough surface morphologies originated from small energy band gap (5.31eV) and microcrystalline structure. In this work, the incorporation of $Al_2O_3$ into $HfO_2$ was obtained by co-sputtering of $HfO_2$ and $Al_2O_3$ without any intentional substrate heating and its structural and electrical properties were investigated by x-ray diffraction (XRD), atomic force microscopy (AFM) and spectroscopic ellipsometer (SE) analyses. The XRD studies confirmed that the microcrystalline structures of $HfO_2$ were transformed to amorphous structures of HfAIO. By AFM analysis, HfAIO films (0.490nm) were considerably smoother than $HfO_2$ films (2.979nm) due to their amorphous structure. The energy band gap ($E_g$) deduced by spectroscopic ellipsometer was increased from 5.17eV ($HfO_2$) to 5.42eV (HfAIO). The electrical performances of TFTs which are made of well-controlled active/electrode IZO materials and co-sputtered HfAIO dielectric material, exhibited a field effect mobility of more than $10cm^2/V{\cdot}s$, a threshold voltage of ~2 V, an $I_{on/off}$ ratio of > $10^5$, and a max on-current of > 2 mA.

• Clean Technology
• /
• v.20 no.2
• /
• pp.189-201
• /
• 2014

Partial oxidation, $CO_2$ reforming and the oxidative $CO_2$ reforming of $CH_4$ to produce synthesis gas over supported Ni hydrotalcite-type ($Ni_{0.5}Ca_{2.5}Al$ catalyst) catalysts were carried out and the effects of metal supports (i.e.; Mg and Ca) on the formation of a stable double-layer structure on the catalysts were evaluated. The $CH_4$ reforming stability was determined to be affected by the differences in the interaction strength between the active Ni ions and support metal ions. Only a Ni-Mg-Al composition produced a highly stable hydrotalcite-type double-layered structure; while the Ni-Ca-Al-type composition did not. Such structure provides excellent stability for the catalyst (-80% efficiency) as confirmed by the long-term $CO_2$ reforming test (-100 h), while the Ni-Ca-Al catalyst exhibited deactivation phases starting at the beginning of the reaction. The interaction strength between the active metal (Ni) and the supporting components (Mg and Al) was determined by temperature-programed reduction (TPR) analyses. The affinity was also confirmed by the TPR temperature because the Ni-Mg-Al catalyst required a higher temperature to reduce the Ni relative to the Ni-Ca-Al catalyst. The highest initial activity for synthesis gas production was observed for the $Ni_{0.5}Ca_{2.5}Al$ catalyst; however, this activity decreased quickly due to coke formation. The $Ni_{0.5}Ca_{2.5}Al$ catalyst exhibited a high reactivity and was more stable than the other catalysts because it had a higher resistance to coke formation.

• The Journal of Korean Academy of Prosthodontics
• /
• v.46 no.2
• /
• pp.137-147
• /
• 2008

Statement of problem: Dental implant procedure has been recognized as a very effective treatment to rehabilitate fully or partially edentulous patients. However, mechanical failures such as screw loosening, screw fracture have been still reported frequently. Purpose: The purpose of this study was to evaluate the influence of tungsten carbide/carbon coating, which has superior hardness and frictional wear resistance, on implant-abutment screw loosening of three different joint connections after one million cyclic loading. Material and methods: The values of detorque before and after loading were measured in three different joint connections (Osstem Implant, Korea), one external butt joint, US II implant system and two internal cones, SS II and GS II system. The values of detorque before loading was analyzed by one-way ANOVA, and two-way ANOVA and Scheffe' test were performed for the value of detorque after loading. Results: 1. The values of initial detorque of tungsten carbide/carbon coated Ti alloy screw were smaller those of Ti alloy screw (P<.01), and there were no differences among implant systems in each screw (P>.05). 2. In comparison of loss rate of detorque value after cyclic loading, US II system was greater than SS II and GS II system but there was no difference between SS II and GS II system (P<.01). 3. Loss rates of detorque value after cyclic loading decreased consistently at tungsten carbide/carbon coated Ti alloy screw comparing with Ti alloy screw in all implant systems (P<.01), and there were no differences among three systems in reduction of loss rates by using tungsten carbide/carbon coated Ti alloy screw (P>.05). Conclusion: Tungsten carbide/carbon coating to increase preload with reduction of friction resistance was a effective way to decrease screw loosening by functional loading.

• Journal of the Korean Magnetics Society
• /
• v.5 no.4
• /
• pp.269-274
• /
• 1995

The basic composition of Mn-Zn ferrite was $Mn_{0.631}Zn_{0.316}Fe_{2.053}O_{4}$(specimen A), $Mn_{0.584}Zn_{0.312}Fe_{2.104}O_{4}$(specimen B) and $Mn_{0.538}Zn_{0.308}Fe_{2.154}O_{4}$(specimen C) with additional 0.1 mol % $CaCo_{3}$ and 0.04 mol % $V_{2}O_{5}$. For high per¬meability and acceleration of grain growth, $CaCo_{3}$ and $V_{2}O_{5}$. was added. The mixture of the law materials was calcinated at $950^{\circ}C$ for 3 hours and then milled. The compacts of toroidal type were sintered at different temperature($1250^{\circ}C$, $1300^{\circ}C$, $1350^{\circ}C$) for 2 hours in $N_2$ atmosphere. The effects of the various raw material composition and sintered temperature on the physical properties of Mn-Zn ferrite have been investigated. They turned out to be spinel structure by X-ray diffraction and the size of grain from SEM was from $18\;\mu\textrm{m}\;to\;23\;\mu\textrm{m}$. As the sintering temperature was increased from $1250^{\circ}C$ to $1350^{\circ}C$, the initial permeability and magnetic induction has increased and the both of Q factor and coercive force has decreased. The coercive force and curie temperature were almost the same at each specimen Their values were about 0.45 Oe and $200^{\circ}C$. The frequency of specimen will used in the range from 200 kHz to 2 MHz. The basic composition of $Mn_{0.584}Zn_{0.312}Fe_{2.104}O_{4}$(specimen B) sintered at $1300^{\circ}C$ shows the best results at magnetic induction (Br & Bm).

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.38 no.4
• /
• pp.415-422
• /
• 2009

We previously demonstrated that zinc plus arachidonic acid (ZA) treatment lowered blood glucose levels in streptozotocin-induced diabetic rats, genetically diabetic obese (ob/ob) mice, and genetically diabetic, non-obese Goto-Kakizaki rats. However, plasma insulin levels did not increase with ZA treatment, suggesting that ZA lowers blood glucose levels not by stimulating pancreatic insulin secretion. However, it is unclear whether these agents lower blood glucose levels by decreasing hepatic glucose output (HGO) or by increasing glucose utilization in peripheral tissues, or both. In order to determine ZA target organ of insulin action, we divided 18 Sprague-Dawley rats weighing ${\sim}130g$ into 3 groups (6 rats per group) and treated them for four weeks with: (1) Control diet (regular rat chow), (2) High fructose (60.0%) diet only, and (3) the same fructose diet plus zinc (10 mg/L) and arachidonic acid (50 mg/L) containing drinking water. After 4 weeks, insulin action was assessed using the hyperinsulinemic euglycemic clamp technique. Food intake and body weights were comparable in all three groups of rats throughout the study period. Plasma glucose and insulin concentrations, glucose uptake, and HGO in the basal state were all the same in these three rat groups. During the clamp study, fructose-treated and fructose+ZA treated rat groups did not exhibit any detectable change on insulin-mediated glucose uptake compared to controls. High fructose feeding impaired insulin mediated suppression of HGO, compared to controls during clamp (4.39 vs. 2.35 mg/kg/min; p<0.05). However, ZA treatment in high fructose-fed rats showed a remarkable increase in hepatic insulin sensitivity compared to high fructose-fed rats, reflected by a complete recovery in suppression of HGO during the clamp (4.39 vs. 2.18 mg/kg/min; p<0.05). This data suggests that ZA increases insulin sensitivity in liver but not glucose utilization of peripheral tissues in high fructose-fed rats.