• Tribology and Lubricants
• /
• v.28 no.2
• /
• pp.93-98
• /
• 2012

The engine oil is an oil used for lubrication of various internal combustion engines. Recently, the vehicle and engine oil manufacture usually guarantee for oil change over 15000~20000 km mileage, but the most of driver usually change engine oil every 5000 km driving in Korea. In this case, it is possible to cause environmental contamination by used engine oil and increase the cost of driving by frequently oil change. In this study, we investigate the various physical properties such as flash point, pour point, kinematic viscosity, cold cranking simulator, total acid number, and four-ball test for fresh engine oil and used engine oil after vehicle driving (5000 km, 10000 km). The test result showed that the total acid number and wear scar by four-ball test of used engine oil had increased than fresh engine oil, but 2 kind of used oil (5000 km and 10000 km) had similar physical properties.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.51 no.2
• /
• pp.140-148
• /
• 2024

This study aimed to enhance the physicochemical properties of sodium iodide-based root filling materials, particularly solubility. In earlier developmental stages, the iodoform-containing paste exhibited high antibacterial efficacy but failed to meet only the solubility requirement among the ISO 6876 criteria. Therefore, this study focused on enhancing the physicochemical properties of the paste under development, particularly centering on reducing its solubility. Four experimental groups were established, including three control group. The previously developed D30 paste was named the Oil 33 group, and the control group was named the Vitapex^® group. The Oil 50 group, in which the oil content was increased, and the Oil 45L group, in which lanolin was incorporated. The physical properties (solubility, pH, flowability, and film thickness) of the four pastes were evaluated according to the ISO 6876 standards. No significant differences were observed between the Oil 45L and Vitapex^® groups in any of the physical property evaluations. While the Oil 33 and Oil 50 groups met the ISO 6876 standards for flowability and film thickness, the Oil 45L group met all the physical properties. However, reducing the overall oil content may be necessary to enhance the antimicrobial properties. The result of the physicochemical experiments showed that the Oil 45L group with the newly formulated composition and incorporated lanolin exhibited low solubility meeting the ISO 6876 standard of ≤ 3%. We were able to develop a paste with more stable solubility than previous iodide-based root-filling materials. Therefore, the oil content must be further adjusted to improve its antimicrobial properties. If other physical properties also meet the ISO 6876 standards and demonstrate excellent results in cytotoxicity tests, this root filling material could potentially replace existing options.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.3
• /
• pp.114-122
• /
• 2002

Electric conductivities, mechanical properties and friction properties were investigated far graphite-nylon composites impregnated with oil. Specific resistivity of composites containing oil from 2% to 6% were in the range of $10^7 ~10^6 \ohm$ cm, which were applicable for anti-static purpose of composites improved by the impregnation of graphite with 2%. Improvement in the impact strength and friction properties of graphite/nylon composites was achieved by the impregnation of oil. The coefficient of friction of the composites containing graphite from 2% to 4% and oil with 2 - 4% showed much loller than that of virgin nylon. Also the abrasive wear of the oil impregnated graphite composites were decreased about 1/3 - 1/10.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11a
• /
• pp.605-608
• /
• 2001

With the intention of investigating the breakdown properties of oil-immersed transformer oils in temperature range of 20∼100[$^{\circ}C$], we are made researches AC breakdown in the gap of 500∼2,500[$\mu\textrm{m}$]. The classification for the physical properties of oil for oil-immersed transformer by FTH and $^1$H-NMR experiments was confirmed to type of mineral oils. As the dependance of breakdown properties due to electrode gap length variation, breakdown voltage was found increasing according to the increase of gap, while dielectric strength was decreasing. As a result the characteristics for AC breakdown, It goes to prove that the breakdown voltage was increased to 90[$^{\circ}C$] but decreased over 90[$^{\circ}C$] in the temperature range. Also, breakdown voltage was found increasing in the increase of gap and the rising of temperature according to Weibull distribution.

• Tribology and Lubricants
• /
• v.37 no.6
• /
• pp.203-207
• /
• 2021

This study presents the development of dielectric constant sensors to measure lubricant properties. The lubricant oil sensor is used to measure oil properties and machine conditions. Various condition monitoring methods are applied to diagnose machine conditions. Machine condition monitoring using oil sensors has advantage over other machine condition monitoring methods. The fault conditions can be noticed at the early stages by the detection of wear particles using oil sensors. Therefore, it provides an early warning in the failure procedure. A variety of oil sensors are applied to check the machine condition. Among all oil sensors, only one sensor can measure the tendency of several properties such as acidity and water content. A dielectric constant sensor is also used to measure various oil properties; therefore, it is very useful. The dielectric constant is the ratio of the capacitance of a capacitor using that material as a dielectric to that of a similar capacitor using vacuum as its dielectric. The dielectric constant has an effect on water content, contaminants, base oil, additive, and so forth. In this study, the dielectric constant sensor is fabricated using MEMS process. In the fabrication process, the shape, gap of the electrode array, and thickness of the insulation material are considered to improve the sensitivity of the sensor.

• Korean Journal of Agricultural Science
• /
• v.46 no.4
• /
• pp.941-953
• /
• 2019

Biodiesels are being explored as a clean energy alternative to regular diesel, which causes pollution. In this study, the optimum conditions for producing biodiesel (BD) by combining beef tallow, an animal waste resource with a high saturated fatty acid content, and corn oil, a vegetable oil with a high unsaturated fatty acid content, were investigated, and the fuel properties were analyzed. Furthermore, Multivariate Analysis of Variance (MANOVA) was used to verify the optimum conditions for producing biodiesel. The influences of control factors, such as the oil blend ratio and methanol to oil molar ratio, on the fatty acid methyl ester and biodiesel production yield were investigated. As a result, the optimum condition for producing blended biodiesel was verified to be tallow to corn oil blend ratio of 7 : 3 (TACO7) and a methanol to oil molar ratio of 14 : 1. Moreover, the interaction between the oil blend ratio and the methanol to oil molar ratio has the most crucial effects on the production of oil blended biodiesel. In conclusion, the analysis results of the fuel properties of TACO7 BD satisfied the BD quality standard, and thus, the viability of BD blended with waste tallow as fuel was verified.

• Tribology and Lubricants
• /
• v.10 no.1
• /
• pp.78-88
• /
• 1994

For the study of chemical and mechanical properties of the synthetic and mineral oil added with two different Zn-DTPs, base and formulated oils were analyzed and compared. Kinematic viscosity and total acid number (TAN) were tested at high temperature for formulated oils. Also the oils added with different alkyl groups of Zn-DTP were tested for thermal stability and TAN changes. The 4-ball machine was used to test for the mechanical properties, such as the coefficient of friction and wear. The worn areas after sliding test were analyzed with microscope and EDX, too. From the study, mineral and synthetic oil have different effects according to the various added ratio of the primary and secondary alkyl groups of Zn-DTP. Also the temperature of test oil affected the anti-wear and friction property of the formulated oils. For synthetic oil, the primery alkyl group of Zn-DTP made better friction properties than that of secondary, while, for mineral oil, secondary alkyt group was better only at low temperature for mineral oil.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.6
• /
• pp.142-149
• /
• 2002

The frictional properties of nylon can be improved by the impregnation of lubricants like wax, oil or graphite. The inclusion of these lubricants, on the other hand, decreases the mechanical properties of nylon, such as tensile strength, hardness and impact strength. As an attempt to maximize frictional properties, while minimizing a decrease in the mechanical properties, various kinds of nylon containing 3 wt% wax and varying contents of oil or graphite were prepared. It was found that the synergy effects to improve both friction and anti-wear properties is evidenced by impregnating a combination of wax/oil or wax/graphite. The wear rate of a nylon containing 3 wt% of wax and 1.5 wt% of oil turned out to be 1/4 of that of nylon impregnated with 8 wt% wax or 8 wt% oil. The latter showed the lowest wear rate among the nylons prepared with a single lubricant. In addition, the friction coefficient of the developed nylon was found to be very similar to the nylon with 8 wt% wax only.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.25 no.4 s.34
• /
• pp.123-131
• /
• 1999

Liquid crystal known as a rheological barrier to coalescence of oil droplets, increases emulsion stability, water-holding capacity and promotes active material penetration to skin. Some investigation for its rheological characteristics have been reported but its relations to consumer perception have been rarely published. In this study, oil/water emulsion and oil/liquid crystal/water systems were manufactured using the same composition or Behenyltrimethylammonium chloride/Cetostearyl alcohol/Lanolin oil. and rheological properties or each system were investigated with Cone and Plate rheometer. The formation of liquid crystalline phase was observed with polarized microscope and Differential Scanning Calorimeter. Continuous shear experiment, creep, yield and water holding capacity were measured for oil/water and oil/liquid crystal/water systems. The results were compared with sensory evaluations. Oil/liquid crystal/water system showed higher,viscosity at the same shear rate. higher viscoelasticity and higher yield stress than oil/water system. These properties were expected to show good spreadability and excellent richness without waxiness in hair can: products of creme type. This expectation was consistent with the results of sensory experiments. Water-holding capacity was evaluated by measuring residual water of specimens at specific temperature and relative humidity. Oil/liquid crystal/water system was proved to have higher ability to hold water in comparison with oil/water system. The results indicated that oil/liquid crystal/water system was of benefit to rheological properties creme type hair care products.

• Proceedings of the SCSK Conference
• /
• 1999.10a
• /
• pp.123-131
• /
• 1999

Liquid crystal known as a rheological barrier to coaleseence of oil dorplets. increases. emulsion stability, water-holding capacity and promotes active material penetration to skin. Some investigation for its rheological characteristics have been reported but its relations to consumer perception have been rarely published. In this study oil/water emulsion and oil/liquid crystal/water systems were manufactured using the same composition of Behenyltrimethylammonium chloride/Cetostearyl alcohol/Lanolin oil. and rheological properties of each system were investigated with Cone and Plate rheometer. The formation of liquid crystalline phase was observed with polarized microscope and Differential Scanning Calorimeter. Continuous shear experiment, creep yield and water holding capacity were measured for oil/water and oil/liquid crystal/water systems. The results were compared with sensory evaluations. Oil/liquid crystal/water system showed higher viscosity at the same shear rate, higher viscoelasticity and higher yield stress than oil/water system. These properties were expected to show good spreadability and excellent richness without waxiness I hair care products of creme type. This expectation was consistent with the results of sensory experiments. Water-holding capacity was evaluated by measuring residual water of specimens at specific temperature and relative humidity, Oil/liquid crystal/water system was proved to have ability to hold water in comparison with oil/water system. The results indicated that oil/liquid crystal/water system was of benefit to rheological properties creme type hair care products.