• 한국자동차공학회논문집
• /
• 제6권6호
• /
• pp.195-201
• /
• 1998

This study aims at the optimal design of rotors and the development of screw type Supercharger of CNG-fueled engine for commercial vehicle. Based on the new rotor profile, an advanced oil free type Supercharger has been developed, which can achieve higher adiabatic efficiency and lower manufacturing cost. The performance test of screw type Supercharger has achieved high volumetric efficiency and the durability on the bench of performance test has also been established in the compact body.

• 한국해양공학회지
• /
• 제33권2호
• /
• pp.139-145
• /
• 2019

It is important that an MGO Chiller System, which is one of the sulfur oxide emission control technologies, is designed to meet the fuel temperature requirements, even with sudden engine load changes. Three different control algorithms (PI, Cascade, and MPC) were applied to an indirect MGO chiller system to compare and analyze the outlet temperature dynamic characteristics of the system through a case study. The results showed that the MPC control method had the best temperature following characteristics in the case study, and the temperature deviation range was reduced by approximately 5% compared to the PI control method.

• Design & Manufacturing
• /
• 제16권2호
• /
• pp.26-32
• /
• 2022

It is known that the fluidized bed incinerator, which is the subject of analysis, shows excellent performance in heat and mass transfer due to excellent mixing and contact performance between fluidized sand and fuel, and also shows relatively good combustion characteristics thanks to good mixing and long residence time for low-grade fuels. have. In this study, air flow analysis is performed to understand the characteristics of co-firing of sludge, waste oil and solid waste in the fluidized bed incinerator, flow characteristics of flue gas, and discharge characteristics of pollutants.The fluidized bed incinerator subject to analysis is a facility that incinerates factory waste and general household waste together with sludge, with a processing capacity of 32 tons/day. to be. In addition, the operation method was designed for continuous operation for 24 hours. As a result, it can be seen that the lower combustion air and the introduced secondary air are changed to a strong turbulence and swirl flow form and exit through the outlet while rotating inside the freeboard layer. The homogeneous one-way flow form before reaching the secondary air nozzle has very high diffusivity with the high-speed jet flow of the nozzle.

• 한국태양에너지학회 논문집
• /
• 제27권1호
• /
• pp.47-54
• /
• 2007

Interests on renewable energy are increased due to oil price and environmental problems aroused from the fossil energy usage. In this study, performances of a solar assisted hybrid heat pump system are analyzed by experimental method. The developed system could runs at two types of operating mode. When the storage temperature is higher than the set temperature, the stored hot water in storage tank is supplied to the load directly. On the other hand, when the storage temperature lower than the set temperature, the water inside of the storage tank is used as heat source of the heat pump. In this study, the system control temperature for the alternation of the operating mode is set to $40^{\circ}C$ of the storage tank outlet. As results, it is founded that the COP of the developed heat pump system shows between 3.0 and 3.5. It is resonable performance for the heating system with a renewable energy as secondary heat source. The solar collect used in this study could supplies heat to the storage tank at over 400 W/m2 solar intensity. If the irradiation is lower than the 400 W/m2, the circulation pump stored and it could not supply heat to the storage tank. It is found that the difference temperature between the outlet of the storage tank and collector is $3^{\circ}C$. Even though, the extended study should be conducted to get a optimum performance of the developed system with various operating condition and control strategies.

• 한국가스학회지
• /
• 제8권1호
• /
• pp.1-6
• /
• 2004

선박용 열교환기의 냉각수로 사용되고 있는 해수의 입구온도는 스팀터빈콘덴서의 경우 약 $25^{\circ}C$이고 출구온도는 약 $60^{\circ}C$이며, 오일쿨러의 경우 출구온도는 약 $40^{\circ}C$이다. 이러한 해수의 온도 변화는 열교환기 세관재의 부식특성에 크게 영향을 미친다. 그러므로 부식손상을 최소화하면서 열교환 효율을 최대로 유지할 수 있는 냉각용액의 온도설정은 매우 중요하다. 따라서 본 연구에서는 $3.5\%$ NaCl + $0.1\%\;NH_4OH$ 수용액의 유동하에서 선박용 열교환기 세관재로 사용되고 있는 Al-황동의 분극 및 응력부식균열 실험을 실시하여 분극특성, 응력부식균열거동 및 탈아연특성에 미치는 용액의 온도의 영향에 대하여 고찰하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제39권6호
• /
• pp.592-598
• /
• 2015

본 연구에서는 공랭식 VI(Vapour-Injection) 사이클을 적용한 R410A용 고성능 하절기 냉방 열펌프의 성능 특성을 실험적으로 규명하였다. 실험에 사용한 장치는 VI 압축기, 응축기, 유분리기, 판형열교환기, 에코노마이져(economizer), 증발기, 그리고 재냉기(re-cooler)로 구성하였다. 냉방 성능 실험 조건은 다음과 같이 3가지 사이클로 VI 사이클을 적용하고 증발기 출구 냉매와 VI사이클 흡입 냉매가 재냉기에서 서로 열교환 하지 않는 사이클(사이클 A)과 열교환을 하는 사이클(사이클 B), 그리고 VI 사이클도 적용하지 않고 증발기 출구 냉매와 VI 사이클 흡입 냉매와의 열교환도 없는 사이클(사이클 C)로 구분하였다. 분석 결과, 냉방 성능은 증발기 출구 냉매와 VI사이클 흡입 냉매가 서로 열교환하는 VI사이클(사이클 B)이 가장 높았으며 VI사이클을 적용하지 않은 사이클 C가 가장 낮음을 알 수 있었으며, 사이클B의 냉방성능계수($COP_C$)가 평균 3.5로 사이클A보다 8.6%, 사이클C보다 33% 높은 값을 나타내었다.

• 플랜트 저널
• /
• 제12권1호
• /
• pp.24-28
• /
• 2016

중유를 연소하는 D 발전소 탈황설비는 운전시간의 경과에 따라 흡수탑 내부에 석고 스케일이 부착되어 발전가능 최대출력의 하향조정이 발생되고 나아가 발전정지를 초래한다. 스케일 제거를 위한 탈황설비 세정은 발전가능 최대출력의 하향조정이 발생하는 시점으로 결정할 수 있다. 본 연구에서는 탈황설비의 운전 자료를 분석하여 발전가능 최대출력의 하향조정이 발생되기 6주전은 탈황설비 출구 $SO_2$ 농도값이 130ppm을 초과하고 동시에 흡수탑 차압은 $380mmH_2O$을 초과하며, 직전 흡수탑 세정 이후 44주가 경과된 시점이 됨을 확인하였다. 최종적으로 흡수탑의 세정시기는 직전 세정시점으로부터 50주가 경과된 시점임을 예측하였다.

• Tribology and Lubricants
• /
• 제37권1호
• /
• pp.25-30
• /
• 2021

The surface texture produced via surface texturing is an important approach for controlling the tribological behavior of friction behavior of mechanical devices. The purpose of this study is to investigate the effect of grooves generated via ultrasonic nanocrystal surface modification (UNSM) technology on the tribological performance of AISI 4150 steel against stainless steel 316L. In the study, tribological tests are performed under two different regimes, namely mixed and hydrodynamic lubrication, by varying the applied normal load and reciprocating speed during the tests. According to the test results, the friction coefficient decreases as static load (10 N, 30 N, and 50 N) of UNSM technology increases in the mixed lubrication regime. Conversely, the friction coefficient increases as the static load (10 N, 30 N, and 50 N) of UNSM technology increases in the hydrodynamic lubrication regime. Hence, the results indicate that micro-grooves generate hydrodynamic pressure in the outlet, which increases the oil film thickness between the two mating surfaces. This potentially leads to a reduction in friction in the mixed lubrication regime due to the prevention of contact of asperities and debris. However, the results indicate an adverse effect in the hydrodynamic lubrication regime. In this regard, additional experiments should be performed to investigate the effect of grooves generated by UNSM technology at varying conditions on the friction behavior of AISI 4150 steel, which in turn can be controlled by the generated pressure and oil film thickness at the contact interface.

• 한국가스학회지
• /
• 제27권2호
• /
• pp.71-78
• /
• 2023

일반적으로 평균 수명이 1.0~1.5년인 전기식 액중형 펌프(electrical submersible pump, ESP)는 유·가스 및 저류층 특성, 운영 조건에 따라 성능 저하 및 수명 감소가 발생하며, 이에 따른 ESP의 고장은 회수 및 설치에 따른 높은 유정 개·보수(workover) 비용과 생산 중단에 따른 추가 비용이 발생한다. 이에 본 연구에서는 유·가스정에서 ESP 장기 운영에 따른 수명을 예측하고자 환형 유동 시스템(flow loop system)을 설계 및 구축하고, ESP 설치 초기 시점부터 고장 시점까지의 ESP 수명에 대한 전 주기 데이터를 취득 및 분석하였다. 구축한 시스템에서 산출되는 데이터 중 ESP의 유체유량, 흡입구 및 토출구의 온도, 압력 그리고 외측부에 설치된 진동 측정기의 데이터 분석을 통하여 ESP 장기 운영에 따른 성능 상태를 정상(normal), 권고 I (advise I), 권고 II (advise II), 유지관리(maintenance), 고장(failed)의 총 5단계로 분류하였다. 실험 결과를 통해 ESP 장기 운영시 단계별 데이터의 경향 차이를 확인하였으며, 이를 통해 운영 기간에 따른 ESP의 상태를 진단하고 펌프의 고장을 예측하였다. 본 연구를 통해 도출된 결과는 유·가스정에서 운영되는 ESP의 상태 모니터링(monitoring) 을 위한 고장 예측 프로그램 및 데이터 분석 알고리즘 개발에 활용될 수 있을 것으로 판단된다.

• 한국지구물리탐사학회:학술대회논문집
• /
• 한국지구물리탐사학회 2003년도 Proceedings of the international symposium on the fusion technology
• /
• pp.695-702
• /
• 2003

In this study, an experimental apparatus has been designed and set-up to analyse the dissociating phenomena of hydrate in porous rock using electric heating method supplied at downhole. The electric heat injecting experiments have been performed to investigate the heat transfer within the core, the dissociating phenomena of hydrate, and the productivities of dissociated gas and water. These experiments were under constant heat injecting method as well as preheating methods. From the experimental results, it is seen that the hydrates is dissociated along the phase equilibrium curve and dissociation of hydrate is accelerated with heat. The injected heat is consumed for the dissociation and also it is lost together with outflow of the dissociated gas and water. From the investigation of gas producing behavior for various heat injecting methods, as the injected heat is greater, dissociation is accelerated faster at outlet and hence the initial gas production becomes higher. Also, it is shown that the initial gas productivity under the constant heating method is better, however, the energy efficiency is low because of smaller amount of the produced gas comparing to the amount of heat injected. In the experiments of preheating method, it was seen that gas production only initial stage is different with the preheating time, but the producing behaviors of gas production are similar.