• 대한기계학회논문집
• /
• 제16권1호
• /
• pp.180-188
• /
• 1992

본 연구에서는 와류실식 디젤 기관에 경유-물의 유화연료 사용시 시관의 회전 속도(1500rpm)가 일정인 경우 물의 첨가량(체적비, 0~20%)과 기관의 부하(BMEP,2.1~ 7.5kg/$\textrm{cm}^2$)변화에 따른 연소실내 압력, 압력상승률 및 열발생률, 착화지연 기간, 연료 소비율 등의 연소특성과 CO, HC, NOx 및 매연의 배출능도 등 유해 배출 가스에 미치는 영향에 관하여 실험적으로 구한 것이다.

• 한국생산제조학회지
• /
• 제22권3호
• /
• pp.447-451
• /
• 2013

In this study, a shock absorber whose orifice area changes according to the oil pressure inside the absorber is developed. The orifice widens and narrows when the oil pressure is high and low, respectively; thus, the orifice area changes according to the oil pressure, in other words, according to the extension/compression velocity. It is well known that the damping force can be expressed as $C{\cdot}v^{\alpha}$. For fluid film damping, the force is proportional to velocity, i.e., ${\alpha}=1$, and for orifice damping, it is proportional to the square of velocity, i.e., ${\alpha}=2$. The shock absorber proposed in this paper can exhibit different relationships between the damping force and velocity because the orifice area changes according to the induced oil pressure. The motivation of this study is to develop a method for designing a shock absorber with desired values of C and ${\alpha}$ which is not just 1 or 2. Theoretical and experimental studies have been conducted to verify the damping characteristics of the shock absorber. The effect of some major design parameters on damping characteristics has been also examined to relate the design parameters to the damping characteristics.

• 동력기계공학회지
• /
• 제17권2호
• /
• pp.29-37
• /
• 2013

Compared to gasoline engines, diesel engines with a relatively simple ignition system are more advantageous in the application of biodeisel fuel to engine. Then in this study the comparative analysis on the spray characteristics and combustion emissions characteristic between the biodiesel(soybean oil) and diesel, the fuel for commercial diesel engine, was performed with common rail injection system. Injection pressure and ratio of biodiesel blended fuel were selected as main experimental variables. Consequently, it can be found that there is no significant difference in the macro characteristics of the spray behavior(spray penetration and spray angle) in response to change in the blend ratio of soybean oil and diesel at a fixed injection pressure, in particular, soot creation in combustion emissions in the region of low pressure was greatly affected by the blend ratio of soybean oil, however, the creation in the region of high pressure was almost unaffected by the blend ratio because of promoted atomization.

• KSTLE International Journal
• /
• 제8권2호
• /
• pp.29-34
• /
• 2007

Recently, requirements relating to performance, environment and noise in the oil hydraulic system of the heavy construction equipment have been reinforced continuously. In order to solve these technical trends, studies on the system compactness, operation under high pressure and great rotating speed, electronic control, substitute oil, and noise reduction have been progressed briskly. Among these recent studies, the system operation under high pressure is quite difficult to carry into effect due to mechanical limitations; that is, for realizing the system operation in the hydraulic pump under high pressure, the improvements or innovations on the design techniques, the manufacturing techniques, and the lubrication performance of the working oil are required. Accordingly, in this study, the stress distribution and optimum design factors under the maximum pressure were discussed by using stress analysis on the cylinder block of the hydraulic axial piston pump, which is one of the most important relative sliding regions.

• Tribology and Lubricants
• /
• 제2권1호
• /
• pp.61-68
• /
• 1986

Effects of the ram-pressure on the THD-performance of pivoted pad thrust bearings are investigated experimentally. A sector-shaped tilting pad thrust bearing and a rotating disk are used. Temperature distribution on the disk surface as well as on the pad surface, distribution of the pressure generated within the fluid film, and the film thickness are measured continuously in the circumferential direction after thermal equilibrium is established. The ram-pressure is proportional to the mean pressure of oil film and to the rotational speed of the disk and affects the maximum pressure and the pressure distribution. The temperature rise on the mating surface of the disc and the pad, contacting with the oil film, is proportional to to the bearing load and the disk speed. The ram-pressure and the temperature rise on the disk surface are dominant factors that affect the THD-performance of pivoted pad thrust bearings.

• 대한기계학회논문집
• /
• 제12권5호
• /
• pp.984-991
• /
• 1988

본 연구에서는 유압관로에서 액주분리를 수반하는 유체 과도현상의 압력파형 에 때때로 관측되는 2단적 압력상승현상의 발생기구를 실험 및 이론적인 추론, 특성곡 선법을 사용한 수치해석을 통하여 명확히 구명함을 목적으로 한다.

• Tribology and Lubricants
• /
• 제25권5호
• /
• pp.311-317
• /
• 2009

To satisfy the more severe emission regulation and the demand of higher fuel economy in near future, the combustion pressure and power output of engines is going to be higher. In order to get the reduction of engine emission and the higher power, it is needed the reduction of the tension and width of ring pack. The lower tension ring and the thinner width ring can bring not only the friction reduction between the ring and liner during engine running, but also the adjustment of the blow-by gas and oil consumption by changing in the pressure in the crevice volume and the axial motion of rings togethe with the adjustment of the inter-ring crevice volumes. In this study, by using a developed basic computer proglram that predicts the blow-by gas and oil consumption of engines, it is to be examined how satisfying the level of the blow-by gas and oil consumption as being installed the piston ring pack with thinner width ring and lower tension ring.

• Journal of Electrical Engineering and Technology
• /
• 제2권1호
• /
• pp.55-60
• /
• 2007

This paper proposes a hydraulic pump system that uses a variable speed SR drive and constant capacity pump. For the design of the SRM (Switched Reluctance Motor) and digital controller, base speed and rating torque are determined from the mechanical specifications of the hydraulic pump. In order to minimize the power consumption during the maintaining of preset oil-pressure, the pressure control system changes the maximum oil-pressure band and flow rate according to the motor speed. The DSP control system adjusts the oil-pressure and the speed of the SRM from the pressure sensor signal, due to conservation of power consumption by the hydraulic pump. A 2.2Kw, 12/8 pole SR motor and DSP based digital controller are designed and tested with experimental set-up. The test results indicate that the system has some good features such as high efficiency and rapid response characteristics.

• Journal of Korean Biological Nursing Science
• /
• 제11권1호
• /
• pp.85-91
• /
• 2009

Purpose: The purpose of this study was to investigate effect of aroma oil inhalation using lavender mixed with bergamot, and sandalwood oil in the ratio of 3:2:1 to the anxiety of colonoscopy patients. Method: The research design was a nonequivalent control group pre-post time experimental research. The data were collected from December, 2004 to March 2005. The total subjects were 60 patients who received colonoscopy at K-hospital in Chuncheon City. An aroma oil inhalation group inhaled for 10 min the mixed aroma oil, 3 drops of which were dropped on the gauze, 20 min before colonoscopy. Result: The anxiety of the intervention group was significantly lower than that of the control group (p=.001). The degree of systolic blood pressure on the intervention group was significantly lower than that of the control group (p=.031). There was no significant difference between the 2 groups in the diastolic pressure (p=.065). Pulse has no significant difference between the aroma oil inhalation and control group (p=.546). Conclusion: The result showed that aroma oil inhalation before colonoscopy has an effect on decreasing anxiety. Thus, the intervention with aroma oil inhalation can be used for relieve anxiety of patients for colonoscopy.

• 한국자동차공학회논문집
• /
• 제16권3호
• /
• pp.60-65
• /
• 2008

A typical louvered-fin oil cooler can be easily contaminated under dusty environment hence resulting in poor performance of a heat exchanger. Thus, in this study, a dust-proof oil cooler has been studied with a unique shape of a 3-dimensional wavy fin since non-louvered fins could have better performance under dusty environment compared to louvered fins. Recently, they have been introduced to commercial and constructional vehicles in Japan. At first numerical analysis has been done to optimize the angle of the wavy fin so that the oil cooler developed can satisfy the target performance. The wavy fin has been then made with roll-forming and roll-pitch stands, and a prototype of an oil cooler with the wavy fin has been finally built with brazing. The performance test showed that the heat release rate of the oil cooler was well beyond the target, 4.94kW and the air-side pressure drop was below the criterion, 0.19kPa. In addition, the results showed that the numerical prediction was effective enough to design the dust-proof oil cooler that satisfies the performance criteria.