• International Journal of Precision Engineering and Manufacturing-Green Technology
• /
• 제5권5호
• /
• pp.637-642
• /
• 2018

The impact of the sintering process, especially in terms of sintering temperature and sintering aid concentration, on the ohmic transport and electrode performance of $(La_{0.80}Sr_{0.20})_{0.95}CoO_{3-{\delta}}$-gadolinia-doped ceria (LSCF-GDC) cathodes is studied. The ohmic and charge-transfer kinetics exhibit a highly coupled $Co_3O_4$ concentration dependency, showing the best performances at an optimum range of 4-5 wt%. This is ascribed to small grain sizes and improved connection between particles. The addition of $Co_3O_4$ was also found to have a dominant impact on charge-transfer kinetics in the LSCF-GDC composite layer and a moderate impact on the electronic transport in the current-collecting LSCF layer. Care should be taken to avoid a formation of excessive thermal stresses between layers when adding $Co_3O_4$.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2007년도 춘계학술대회
• /
• pp.157-160
• /
• 2007

The catalyst layer of a proton exchange membrane (PEM) fuel cell is a mixture of polymer, carbon, and platinum. The characteristics of the catalyst layer play critical role in determining the performance of the PEM fuel cell. This research investigates the role of catalyst layer composition using a Central Composite Design (CCD) experiment with two factors which are Nafion content and carbon loading while the platinum catalyst surface area is held constant. For each catalyst layer composition， polarization curves are measured to evaluate cell performance at common operating conditions, Electrochemical Impedance Spectroscopy (EIS), and Cyclic Voltammetry (CV) are then applied to investigate the cause of the observed variations in performance. The results show that both Nafion and carbon content significantly affect MEA performance. The ohmic resistance and active catalyst area of the cell do not correlate with catalyst layer composition, and observed variations in the cell resistance and active catalyst area produced changes in performance that were not significant relative to compositions of catalyst layers.

• 마이크로전자및패키징학회지
• /
• 제10권4호
• /
• pp.29-33
• /
• 2003

n-형 탄화규소 반도체에 대한 구리금속을 이용하여 오옴성 접촉 구조를 제작하였다. 제작된 구리접촉에 대해 후속열처리 조건과 금속접촉 구조에 따른 재료적, 전기적 성질의 변화를 조사하였다. 금속접촉의 오옴성 성질은 금속박막의 구조 뿐 아니라 열처리조건에 대해서도 크게 좌우됨을 알 수 있었다. 열처리는 급속열처리 장치를 이용한 진공상태 및 환원 분위기에서 2단계 열처리방식을 통하여 시행하였다. 접촉비저항의 측정을 위해 TLM 구조를 만들었으며 면저항 ($R_{s}$), 접합저항 ($R_{c}$), 이동거리 ($L_{T}$), 패드간거리 (d), 전체저항 ($R_{T}$) 값을 구하여 알려진 계산식에 의해 접촉비저항 ($p_{c}$) 값을 추정하였다. 진공보다 환원분위기에서 후속 열처리를 수행한 시편이 양호한 전기적 성질을 가짐을 알 수 있었다. 가장 양호한 결과는 Cu/Si/Cu 구조를 가진 금속접촉 결과이었으며 접촉비저항 ($p_{c}$)은 $1.2\times 10^{-6} \Omega \textrm{cm}^2$의 낮은 값을 얻을 수 있었다. 재료적 성질은 XRD를 이용하여 분석하였고 SiC 계면 상에 구리와 실리콘이 결합한 구리 실리사이드가 형성됨을 알 수 있었다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 하계학술대회 논문집 C
• /
• pp.1378-1380
• /
• 2001

Ohmic contacts have been fabricated on p-type 4H-SiC using Pt/Ti. Low resistivitf Ohmic contacts of Pt/Ti to p-type 4H-SiC were investigated. Specific contact resistances were measured using the transmission line model method, and the physical properties of the contacts were examined using x-ray diffraction, scanning electron microscopy. Ohmic behavior with linear current-voltage characteristics was observed following anneals at $900^{\circ}C$ for 90sec at a pressure of $3.4{\times}10^{-5}$ Torr. The Pt/Si/Ti films was measured lower value of the specific contact resistance by the annealing process, and the contact resistances were improved more than one order compared to Ti contact the annealed sample. Scanning electron microscopy shows that the Pt layer effectively reduce the oxidation of Ti films. And results are obtained as $4.6{\times}10^{-4}$ ohm/$cm^2$ for a Pt/Ti metal structure after a vacuum annealing at $900^{\circ}C$ for 90sec. Titanium has a relatively high melting point, thus Ti-based metal contacts were attempted in this study.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 하계학술대회 논문집
• /
• pp.160-160
• /
• 2010

In this work, we investigate ohmic contacts to p-type GaN using a Pt/Cu/Au metallization scheme in order to achieve low resistance and thermally stable ohmic contact on p-GaN. An ohmic contact formed by a metal electrode deposited on a highly doped InGaN/GaN superlattice sturucture on p-GaN layer. The specific contact resistance is $1.56{\times}10^{-6}{\Omega}cm^2$ for the as-deposited sample, $1.35{\times}10^{-4}{\Omega}cm^2$ for the sample annealed at $250^{\circ}C$ and $6.88{\times}10^{-3}{\Omega}cm^2$ for the sample annealed at $300^{\circ}C$.

• 한국재료학회지
• /
• 제12권12호
• /
• pp.918-923
• /
• 2002

In this work, CdTe films were deposited on CdS/ITO/glass substrate by a close spaced sublimation (CSS) method. A $Cu_2$Te layer was deposited on the CdTe film by evaporating $Cu_2$Te powder. Then the samples were annealed for p+ ohmic contact. TEM and XRD analysis showed that $CdTe/Cu_2$Te interface exhibited different forms with various annealing temperature. A good p+ ohmic contact was achieved when the annealing temperature was between $180^{\circ}C$ to $200^{\circ}C$. Best cell efficiency of 12.34% was obtained when post annealing temperature was $200^{\circ}C$ for 5 min. Thermal stress test of the CdS/CdTe cells with carbon back contact showed that the $Cu_2$Te contact was stable at $50^{\circ}C$ in $N_2$ and was slowly degraded at $100^{\circ}C$ in $N_2$. In comparison to the conventional carbon contact, the $Cu_2$Te contact showed a better thermal stability.

• 대한금속재료학회지
• /
• 제48권6호
• /
• pp.565-569
• /
• 2010

We report on the characteristics of indium-oxide-doped ZnO (IZO) ohmic contact to p-GaN. The IZO ohmic contact layer was deposited on p-GaN by a Roll-to-Roll (RTR) sputter method. IZO contact film with a thickness of 360, 230 and 100 nm yielded an ohmic contact resistance of $4.70{\times}10^{-4}$, $5.95{\times}10^{-2}$, $4.85{\times}10^{-1}\;{\Omega}cm^{2}$ on p-GaN when annealed at $600{^{\circ}C}$ for 1 min under a nitrogen ambient, respectively. While the transmittance of IZO film with a thickness of 360 nm slightly increased in the wavelength range of 380-800 nm after annealing, the transmittance rapidly increased up to 80% after annealing at $600{^{\circ}C}$ in the wavelength range of 380~430 nm because the crystallization of IZO film and created Ga vacancies near the p-GaN surface region were affected by the annealing. These results indicate that ohmic contact resistance and transmittance of the IZO films improved.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제51권11호
• /
• pp.546-550
• /
• 2002

In this paper, Heterojunction phototransistors(HPT's) with an optically transparent ITO emitter contacts were fabricated. The ITO ohmic contacts were realized by employing thin imdium layer between the ITO and $n^+$-InP layers. The ITO contact was annealed at $250^{\circ}C$. The specific contact resistance of about $6.6{\times}10^{-4}{\Omega}cm^2$ was measured by use of the transmission line model (TLM). Heterojunction bipolar transistors (HBTs) having the same device layout were fabricated to compare with HPTs. The DC characteristics of the InP/InGaAs HPT showed the similar electrical characteristics of the HBT. Emitter contact resistance($R_E$) of about $6.4{\Omega}$ was extracted, which was very similar to that of the HBT. The optical characteristics of HPT's were generated by illuminating the device with light from $1.3{\mu}m$ light. It showed that HPT's can be controlled optically.

• 대한전자공학회논문지
• /
• 제26권9호
• /
• pp.1381-1387
• /
• 1989

For the fabrication of ohmic contact to p-type GaAs, In Liquid Metal Ions were implanted into p-type GaAs (Zn:1.5x10**19/cm**3). After the samples were processed by Infrared rapid thermal annealing (IRTA0 or Furance Annealing (FA), I-V and specific contact contact resistivity were measured. Specific contact resistivity was found to be 1.7x10**-5 \ulcorner-cm\ulcornerin IRTA 750\ulcorner, 10 sec annealed sample. The surface characteristics of the samples were investigated with SEM, RHEED, AES. From these results we can know that implanted In ions were formed mixing layer of InAs at the surface.

• 대한전자공학회논문지
• /
• 제27권4호
• /
• pp.555-562
• /
• 1990

Alloyed ohmic contact properties of Au-Zn/Au, Au-Be/Au,Au-Zn/Cr/Au, and Au-Be/Cr/Au metal system to p-InP were investigated. Optimum alloying conditions were obtained at the annealing temperature of 425\ulcorner for all the metal systems using a rapid thermal annealing system. Surface AES analysis and auger depth profiling were done for each metal system annealed at the optimum conditions. Outdiffusions of In and P from the InP substrate were found in the metal systems without Cr intermediate layer. Also, small amount of In. P and Cr were detected at the surface in the case of Au-Zn/Cr/Au system, while there were occured no outdiffusion of In, P, and Cr for Au-Be/Cr/Au system. The best surface morpholoty and specific contact resistivity of 4.5x 10**-5 \ulcornercm\ulcornerhave been obtained in this Au-Be/Cr/Au material system alloyed at 425\ulcorner for 60 second.