• International Journal of Naval Architecture and Ocean Engineering
• /
• v.7 no.3
• /
• pp.500-508
• /
• 2015

High-speed heavy loaded monohull ships can benefit from application of drag-reducing air cavities under stepped hull bottoms. The subject of this paper is the steady hydrodynamic modeling of semi-planing air-cavity hulls. The current method is based on a linearized potential-flow theory for surface flows. The mathematical model description and parametric calculation results for a selected configuration with pressurized and open air cavities are presented.

• Journal of Ocean Engineering and Technology
• /
• v.34 no.2
• /
• pp.77-88
• /
• 2020

In this study, heading characteristics and heading control performances were evaluated to achieve the wave shield effect. The wave shield effect originating from heading control reduces the relative motions of moored vessels in a floating liquefied natural gas bunkering terminal (FLBT). Therefore, loading and off-loading performances are improved through reduced relative motion. For the objective of this study and efficiency of the analysis, a simplified model was used that assuming no relative motion of the moored vessels in the FLBT. The simplified model involved modeling the environmental loads and inertia of several floating bodies, including FLBT, into the environmental loads and inertia of a single vessel. The simplified model was validated through comparisons with model tests. With the simplified model, heading characteristics and heading control simulations were performed using low-frequency planar motion equations. The heading characteristics and heading control performances of FLBT were analyzed through the results of simulations under the expected environmental conditions. The capacity of the tunnel thrust for the heading control performance was confirmed to be adequate for improvement of the loading and off-loading performances using the wave shielding effects under the operation conditions.

• Journal of Ocean Engineering and Technology
• /
• v.20 no.1 s.68
• /
• pp.69-76
• /
• 2006

The design of efficient search path to maximize the Cumulative Detection Probability(CDP) is mainly dependent on experience and intuition when searcher detect the target using SONAR in the ocean. Recently with the advance of modeling and simulation method, it has been possible to access the optimization problems more systematically. In this paper, a method for the optimal search path calculation is developed based on the combination of the genetic algorithm and the calculation algorithm for detection range. We consider the discrete system for search path, space, and time, and use the movement direction of the SONAR for the gene of the genetic algorithm. The developed algorithm, OASPP(Optimal Acoustic Search Path Planning), is shown to be effective, via a simulation, finding the optimal search path for the case when the intuitive solution exists. Also, OASPP is compared with other algorithms for the measure of efficiency to maximize CDP.

• Journal of Ocean Engineering and Technology
• /
• v.34 no.3
• /
• pp.167-179
• /
• 2020

Recently, the increasing importance of artificial intelligence (AI) technology has led to its increased use in various fields in the shipbuilding and marine industries. For example, typical scenarios for AI include production management, analyses of ships on a voyage, and motion prediction. Therefore, this study was conducted to predict a response amplitude operator (RAO) through AI technology. It used a neural network based on one of the types of AI methods. The data used in the neural network consisted of the properties of the vessel and RAO values, based on simulating the in-house code. The learning model consisted of an input layer, hidden layer, and output layer. The input layer comprised eight neurons, the hidden layer comprised the variables, and the output layer comprised 20 neurons. The RAO predicted with the neural network and an RAO created with the in-house code were compared. The accuracy was assessed and reviewed based on the root mean square error (RMSE), standard deviation (SD), random number change, correlation coefficient, and scatter plot. Finally, the optimal model was selected, and the conclusion was drawn. The ultimate goals of this study were to reduce the difficulty in the modeling work required to obtain the RAO, to reduce the difficulty in using commercial tools, and to enable an assessment of the stability of medium/small vessels in waves.

• Ocean and Polar Research
• /
• v.25 no.3
• /
• pp.287-302
• /
• 2003

The seasonal variations in the circulation of the water mass in the East Sea/Japan Sea have been simulated using a free surface primitive ocean model, RIAMOM (RIAM Ocean Model), comparing the results from GFDL-MOM1 (Geophysical Fluid Dynamics Laboratory Modular Ocean Model, version 1.1, hereafter MOM) with the GDEM (Generalized Digital Environmental Model) data. Both models appear to successfully reproduce the distinct features of circulation in the East Sea/Japan Sea, such as the NB (Nearshore Branch) flowing along the Japanese coast, the EKWC (East Korean Warm Current) flowing northward along the Korean coast, and the NKCC/LCC (North Korean Cold Current/Liman Cold Current) flowing southwestward along Korean/Russian coast. RIAMOM has shown better performance, compared to MOM, in terms of the realistic simulation of the flow field in the East Sea/Japan Sea; RIAMOM has produced more rectified flows on the coastal region, for example, the narrower and stronger NKCC/LCC than MOM has. There is however obvious differences between the model results and the GDEM data in terms of the calculation of the water mass; both models have shown a tendency to overpredict temperature and underpredict salinity below 50m; more diffusive forms of thermocline and halocline have been simulated than noted in GDEM data.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.6 no.3
• /
• pp.309-325
• /
• 1994

Ocean circulation in the Gulf of Alaska is remarkably constant throughout the year despite of being forced by one of the largest seasonal wind stresses in the world. To explain the small seasonal changes in the transport of Alaska Stream. a set of numerical models is employed. First a diagnostic approach is applied to reproduce circulation from the observed density structure. The results reveals the very small seasonal changes in the Alaska Stream transport. Next a series of the prognostic models is used: a barotropic model. a flat bottom baroclinic model, and baroclinic model with topography. These models reveal the influence of topography and baroclinicity on the ocean's response to the seasonal wind forcing. The intercomparisons of the various model results suggest that the seasonal response of the baroclinic ocean is primary barotropic and the resultant barotropic circulation is weakened by the scattering effect of the bottom topography.

• Journal of the Society of Naval Architects of Korea
• /
• v.53 no.2
• /
• pp.101-107
• /
• 2016

Generally, the shipbuilding industry has finite resources and limited workspace. Due to finite resources, limited workspace and state of block preparation, erection process in shipbuilding industry is frequently delayed than erection process scheduling which is planned at long-term plan stage. In this study, considering variability of block reserve ratio, the degree of delay in real erection process is measured and compared to scheduling which is planned at long-term plan stage in shipbuilding industry including finite capacity and variative lead time. Also, the erection process scheduling which has minimum lead time can be checked through simulation. The results of this study could be improved the accuracy of erection process scheduling by checking the main event compliance ratio by block reserve ratio and calculating the optimum erection pitch for the main event compliance.

• Journal of Ship and Ocean Technology
• /
• v.5 no.2
• /
• pp.1-13
• /
• 2001

Data in one Product Model for shipbuilding is inevitably referenced and manipulated during each phase of design or production activities, and data or manipulation status naturally varies from the original with the advance of each activities. For Object-Oriented approach, it is hard to identify classes dealing with those variations, and even if once a product model is developed, it might be getting much harder to modify it to cope with a new additional phase of activities. This paper proposes an Instance-Oriented Modeling Method, temporarily named “Concept-Relationship Modeling Approach”, which handles Data structure and Behavior independently of each other in order to resolve the difficulties above.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.6 no.4
• /
• pp.935-946
• /
• 2014

This paper investigates the noise transmission performance of industrial mufflers widely used in ships based on the CAE modeling and simulation. Since the industrial mufflers have very complicated internal structures, the conventional Transfer Matrix Method (TMM) is of limited use. The CAE modeling and simulation is therefore required to incorporate commercial softwares: CATIA for geometry modeling, MSC/PATRAN for FE meshing and LMS/SYSNOISE for analysis. Main sources of difficulties in this study are led by complicated arrangement of reactive elements, perforated walls and absorption materials. The reactive elements and absorbent materials are modeled by applying boundary conditions given by impedance. The perforated walls are modeled by applying the transfer impedance on the duplicated node mesh. The CAE approach presented in this paper is verified by comparing with the theoretical solution of a concentric-tube resonator and is applied for industrial mufflers.

• Journal of the Society of Naval Architects of Korea
• /
• v.45 no.4
• /
• pp.432-440
• /
• 2008

Korean shipbuilders are starting to use three dimensional solid CAD systems to enhance their competitiveness in design and production. Despite many merits, three dimensional CAD systems reveal some problems in pipe-line modeling. Pipe-line modeling is heavily dependent on point data in routing. However, since the models built by sweeping or skinning operations do not have data about points and lines on the surfaces, the point data for routing are currently manually calculated by considering the diameters of the pipes and alignment conditions with other pipes. This process is inefficient and prone to errors. In order to enhance the pipe modeling, this paper presents an Offset Routing Program for a three dimensional CAD system, which aids designers to easily define the start points and to generate the pipe routings using reference objects.