• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2009.04a
• /
• pp.84-89
• /
• 2009

In this paper, the experimental study on the identification of noise sources and noise transmission paths was carried out for the cabin noise control of construction equipment. In order to investigate noise and vibration characteristics of cabin structure, sound absorption, transmission, and radiation tests were performed using cabin assembly models. The noise/vibration source levels were obtained from the real cabins of wheel loader and excavator. Using transfer functions of cabins and real cabins' source data, cabin noise was decomposed into airborne and structureborne noise transmissions. Finally noise sources and major transmission paths were successfully identified for wheel loader and excavator's cabins.

• Journal of Advanced Marine Engineering and Technology
• /
• v.27 no.3
• /
• pp.381-387
• /
• 2003

Engine noise consists of the noise radiated from an engine structure and noises from engine ancillaries such as a turbocharger fuel injection system, and alternator. The noise of these ancillaries might be incorrectly evaluated in the aspect of the noise contribution to engine noise because the noise reflection effect of their neighbor engine structure is easily ignored. Consequently, noise source identification should be misled. This study investigates the fact that the engine structure located around an alternator reflects alternator noise, and the reflected noise acts as another alternator noise source in a heavy-duty diesel engine. The result shows that the alternator noise can be correctly estimated in engine noise by properly including the noise reflection effect.

• Proceedings of the KIEE Conference
• /
• 2005.07d
• /
• pp.3063-3065
• /
• 2005

In the raper, the noise involved on the active circuit is identified using correlation function. In order to identify the unknown noise source location, signals from each points on the system are detected and the location is identified by a concept calico Noise Source Surface. The fault diagnosis method is suggested for each element by identifying the noise source in active circuit using SVM. Experiment is conducted to confirm the validity of the proposed method. Also a method to reduce and control the noise in the system signal by using Matrix Pencil Method is introduced.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.19 no.4
• /
• pp.347-354
• /
• 2009

Frequency analysis is one of the most useful way to analyze response signal for the purpose of grasping the dynamic characteristics of system through Fourier transformation. Although it is very effective way for frequency analysis, it is hard to analyze out a specific sound or vibration component which is correlated with others. In this thesis, source contribution analysis tool for NI-PXI equipment is developed with LabVIEW using coherences of MISO(multiple-input single-output) model. For the purpose of examining propriety of developed tool, simulation is performed with several correlated signals that have different frequency range. After checking the OCF(ordinary coherence function) and PCF(partial coherence function) of the each signal for concerned frequency domain, an experiment is conducted on an evaporator that cause the principal noise of a refrigerator. This developed tool will be expected to build up more convenient and serviceable measurement system.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.11a
• /
• pp.911-915
• /
• 2004

Recently, several experimental techniques for identifying the noise sources distributed over a moving vehicle are being developed and used in order to design a low noise vehicle. The beamforming method, which uses phase information between several microphones to localize the source position, is proved to be one of the promising techniques applicable even under complicated test environments. In this study a beamforming algorithm is developed and applied to measure the dominant noise sources on a passenger car moving at constant speed. Unlike the acoustic signals from a stationary noise source, the sound generated from a moving source is distorted due to the Doppler effects. The sound pressure are measured with an spiral array system composed of 26 microphones and a pair of photo sensors are used to measure the. vehicle speed. The information about the speed and relative position of the vehicle are used to eliminate the Doppler effects from the measured pressure signal by using a de-Dopplerization algorithm. The noise generated from a moving vehicle can be grouped in many ways, however, tire noise and the noise generated from the engine are distinguishable at the speeds being tested.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2010.10a
• /
• pp.542-542
• /
• 2010

• Journal of KSNVE
• /
• v.8 no.3
• /
• pp.435-440
• /
• 1998

The main objective of this study is to estimate location and strength of sound sources distributed on the surface of an enclosure. Acoustic holography method has been used to identify the sources in an interior sound field. However, it can not completely distinguish between the direct sound field from sources and the reflections from surfaces. The method just reconstructs the entire sound field based on the sound pressure at the finite number of measurement points. In this stduy, a method which estimates only the active sources by using measurements of field pressure and surface admittance is proposed. An in-situ technique to estimate the general boundary condition is also proposed by using acoustic holography, assuming the surfaces are locally reacting.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.3
• /
• pp.171-171
• /
• 1997

Sound intensity distributions and energy flow in the near field of dipole source system and flat plate were investigated. First, the effectiveness of complex acoustic intensity was proved by using mathmatical and experimental methods in order to indentify noise sources and transmission paths of dipole field which is effected by the presence of neighbouring coherent sources. Next, analytical complex acoustic intensity method was discussed and the characteristics and energy flow of sound induced from the plate are clarified. The velocity of plate obtained from Finite Element Method was used for calculation of complex acoustic intensity in the near field. Finally experimental complex acoustic intensity method was applied to a passenger car. It can be seen that complex acoustic intensity method using both of active and reactive intensity is vital in devising a strategy for the identification and the reduction of vibration and noise.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.3
• /
• pp.159-171
• /
• 1997

Sound intensity distributions and energy flow in the near field of dipole source system and flat plate were investigated. First, the effectiveness of complex acoustic intensity was proved by using mathmatical and experimental methods in order to inden- tify noise sources and transmission paths of dipole field which is effected by the presence of neighbouring coherent sources. Next, analytical complex acoustic intensity method was discussed and the characteristics and energy flow of sound induced from the plate are clarified. The velocity of plate obtained from Finite Element Method was used for calculation of complex acoustic intensity in the near field. Finally experimental complex acoustic intensity method using both of active and reactive intensity is vital in devising a strategy for the identification and the reduction of vibration and noise.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1996.10a
• /
• pp.43-49
• /
• 1996

소음원의 특성을 규명하는 방법론들은 방위각 추정 방법론에 근간을 둔 소음원 위치 탐지 방법과 같이 소음원의 등가 단극음원 크기 및 위치들을 추정하는 기본적인 방법들로부터 보다 많은 계측기기 및 탐촉자와 함께 상당히 정교한 데이타 처리를 수행하여야 하는 인텐시티를 이용한 음장 맵핑(mapping) 홀로그라프를 이용한 관심음장 전체의 3차원 맵핑등 실로 다양하다 할 수 있다. 결국은 가장 많은 탐촉자를 사용하는 측정 시스템이 보다 많은 음장의 정보를 제공하므로서 가장 탁월한 방법론이라 결정할 수 있다. 이것은 특히 탐촉자 자체의 가격이 저렴해져 가는 추세인 점과 소형화하는 추세를 감안하여 봄과 동시에 공간상의 물리적인 의미 즉 파수영역에 대한 보다 폭 넓은 이해를 통한 시간, 공간, 주파수, 파수영역 즉 확대된 차원에서의 음장, 소음에 대한 이해를 갖을 수 있다는 면에서도 가치 있다고 할 수 있다.