• Corrosion Science and Technology
• /
• v.16 no.4
• /
• pp.194-200
• /
• 2017

Stress-corrosion cracking (SCC) of alloy 600 and alloy 800 in 0.5 mol/L thiosulfate solution during constant strain was investigated using electrochemical noise (EN) combined with 3-D microscope techniques. The in-situ morphology observation and EN results indicate that the SCC process could be divided into three stages: (1) passive film stabilization and growth, (2) crack initiation, (3) and crack growth. Power Spectral Density (PSD) and the probability distribution obtained from EN were used as the "fingerprint" to distinguish the different processes. During passive film stabilization and growth, the current noise signals resembled "white noise": when the crack initiated, many transient peaks could be seen in the current noise and the wavelet energy at low frequency as well as the noise resistance decreased. After crack propagation, the noise amplitudes increased, particularly the white noises at low and high frequencies ($W_L$ and $W_H$) in the PSDs. Finally, the detection of metal structure corrosion in a simulated sea splash zone and pipeline corrosion in the atmosphere are established.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.11
• /
• pp.1584-1590
• /
• 2017

This paper presents a implementation method of reliable speed limitation controller considering motor parameter variation in high speed operation. In spinning process of drum washing machine, speed increase has to be limited when unallowable imbalance mass is detected. Otherwise, severe noise and vibration can happen because noise and vibration are proportional to imbalance mass. To detect imbalance mass, d-axis current magnitude is used. However, we have to compensate for back-emf and power supply variation by means of detecting them because d-axis current is affected by both of them. On the other hand, we have to carefully estimate back-emf because back-emf is affected by stator resistance variation and inverter voltage error. Stator resistance variation can happen by manufacturing process for mass production or temperature variation in running. And there are inverter voltage errors between command voltage from micro-computer to inverter and real voltage from inverter to motor because of rising and falling time delay and turn-on resistance of power semiconductor switch. To solve this problem, we propose 2-step align current injection method which is to inject step-wise current right before starting. By this method, we can simply obtain stator resistance by ratio of voltage without inverter voltage error and current, and we can measure inverter voltage error. So we can obtain more exact model current, and then by simple calculation with compensation gain, we can estimate more accurate motor back-emf. We show that this method works well. It is verified through experiments.

• Journal of Adhesion and Interface
• /
• v.24 no.4
• /
• pp.124-130
• /
• 2023

For automotive coating agents that require little change in characteristics due to changes in external temperature, changes in noise characteristics due to changes in the external environment are very important. Therefore, soft polyurethane with excellent cold resistance, weather resistance, and abrasion resistance, and polysiloxane whose -OH terminated and side chains are modified with amines, are widely used. In this study, coating agents was prepared by adding water-born polyurethane, polysiloxane, ultra high molecular weight polypropylene (UHMWPP) powder, carbon black, and a matting agent to determine the effect of each resin component on noise. To study the effect of each resin component on noise, a coating agent was prepared by adding water-born polyurethane, polysiloxane, UHMWPP powder, carbon black, and a matting agent. The hard/soft segment ratio of water-born polyurethane, the main component of the coating, was 27.1%/72.9%, and the ratio of amino siloxanes to hydroxy-terminated polysiloxane was 2:7, which produced the least noise. The difference in friction coefficient was large when the friction body moves at high speed. When UHMWPP powder replaced SiO₂, noise decreased and gloss also decreased.

• International Journal of Highway Engineering
• /
• v.12 no.1
• /
• pp.87-98
• /
• 2010

Surface of fine-size exposed aggregate Portland cement concrete pavements is consists of exposed coarse aggregate by removing upper 2~3mm mortar of concrete slab. Fine-size exposed aggregate PCC pavements have advantages of maintaining low-noise and adequate skid-resistance level during the performance period. In order to provide the successful exposed concrete aggregate pavement, uniform distribution of the coarse aggregate on pavement surface through adequate the mix design and exposing method. In this study, evaluated initial performance of fine-size exposed aggregate PCC pavement by experimental construction. And it was known that fine-size exposed aggregate concrete pavement which can reduce the noise and maintain the adequate level of skid resistance and strength.

• Corrosion Science and Technology
• /
• v.11 no.4
• /
• pp.135-140
• /
• 2012

The linear polarization resistance method is one of the widely used techniques for the corrosion rate monitoring in the water circulating systems of plants. The measurement is simple and rapid, so that a continuous on-line monitoring is possible without any shutdown of plants. A 2-electrode polarization corrosion rate measurement system was installed in a laboratory using a data acquisition board and PC. The signal processing parameters were optimized for the accurate corrosion rate measurement, and the polarization resistance was compensated with the solution resistance measured by the high frequency sine wave signal of an output channel. The precision of corrosion rate data was greatly improved by removing the initial noise signals on measuring the polarization resistance.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.8
• /
• pp.748-753
• /
• 2002

In this paper, a new topology of a active capacitor is proposed in order to apply the resonator in the design of RF active bandpass filters. Through the noise analysis of the active capacitor, the optimized low noise design process is also presented, Due to the low noise performance of the proposed active bandpass filter, it can be used in the RF front-end of the receivers. In designed 2-stage active bandpass filter at 1.9 GHz shows insertion loss of 0 dB, noise figure of 2.6 dB, and OIP3 of 8 dBm.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.11a
• /
• pp.253-256
• /
• 2004

Acoustical noise at low frequency range (below 500Hz) of refrigerator result from fans which are inside of the refrigerator. In generally to evaluate and apply to refrigerator it is recommended that acoustical noise and fluidic performance of the fan were measured simultaneously. To do that twin-room type anechoic wind tunnel was needed. But constructing twin room type anechoic wind tunnel was very expensive and estimation of small refrigerator fan performance was not easy. So in this paper we composed anechoic fan tester. A successful noise and performance measurement was performed using the anechoic fan tester. Existing 22 kinds of refrigerator fan were investigated and mapped into one database. Refrigerator duct pressure resistance were measured and reflected into the fan database to find out appropriate fan. Through the application of fan database, the refrigerator became less noise compared to current one and these data shows what is the best way to reduce fan noise.

• Proceedings of the KSR Conference
• /
• 2000.11a
• /
• pp.499-505
• /
• 2000

The shape of the KHST, and of the power car in particular, is largely determined by aerodynamic considerations. At high speeds, air resistance accounts for the major part of overall resistance to forward motion. Further points to be considered are environmentally undesirable acoustic phenomena and pressure waves. Minimizing power requirements and environmentally-unfriendly noise and pressure waves are thus major objectives in the development of the KHST. When deciding on the aerodynamic design of the power car, the entire train set has to be taken into consideration. This paper describes the design process and results about the front shape of the KHST.

• Proceedings of the KIPE Conference
• /
• 2003.07b
• /
• pp.520-523
• /
• 2003

In this paper, heatsink design for high power converter is presented. There are many ways of designing heatsink, but air cooling is by far the most used and much more practical than any of the other methods. In this paper, the practical methods of cooling which include the method to reduce a noise and a vibration due to a fan and the method to design a gap resistance and a contact resistance due to mounting force between thyristor and heatsink is proposed. Finally, simulation and experimental results are described to verify validity of the proposed method.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.5
• /
• pp.1724-1728
• /
• 2014

Heat sink has been used to help an electrical device operate in normal temperature condition. But heat sink radiates unwanted electromagnetic wave, which may cause electromagnetic interference problem. A resistance loaded grounding technique is proposed to reduce electromagnetic wave radiation by a heat sink. Numerical simulations are accomplished to find optimal loading resistance. Also electromagnetic fields radiated by from a heat sink are measured and compared with the simulation results. The test results verify the usefulness of the proposed technique.