• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08b
• /
• pp.1284-1287
• /
• 2007

Titanium dioxide ($TiO_2$) is promising candidate for fabricating blocking layer of gate dielectrics in non-volatile memory (NVM). In this work, we investigated $TiO_2$ as high dielectric constant material instead of silicon dioxide ($SiO_2$), which is generally used as blocking layer for NVM.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.48 no.2
• /
• pp.69-75
• /
• 1999

The characteristics of $H_2$ gas detection have been investigated using the Pt-MIS capacitor composed of the LPCVD nitride on the oxide. The flat band voltage shift is measured as 0.1 V in 1,000 ppm $H_2$ gas ambient and to be independent of Pt catalyst thickness. It is found that the flatband voltage shift is proportional to the hydrogen concentrations. The response and recovery time of Pt-MIS capacitor are 5 mins and 25 mins respectively. The samples of 30nm thick Pt revealed much higher sensitivity than that of 150nm samples. The samples of 150nm Pt showed that the flatband voltage shift of the device is due to the formation of the dipole layer of the adsorbed hydrogen atoms at the Pt-insulator interface.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.1
• /
• pp.1-5
• /
• 2001

STI(shallow trench isolation)-CMP(chemical mechanical polishing) process have been substituted for LOCOS(local oxidation of silicon) process to obtain global planarization in the below sub-0.5㎛ technology. However TI-CMP process, especially TI-CMP with RIE(reactive ion etching) etch back process, has some kinds of defect like nitride residue, torn oxide defect, etc. In this paper, we studied how to reduced torn oxide defects after STI-CMP with RIE etch back processed. Although torn oxide defects which can occur on trench area is not deep and not severe, torn oxide defects on moat area is not deep and not severe, torn oxide defects on moat area is sometimes very deep and makes the yield loss. Thus, we did test on pattern wafers which go through trench process, APECVD process, and RIE etch back process by using an IPEC 472 polisher, IC1000/SUVA4 PAD and KOH base slurry to reduce the number of torn defects and to study what is the origin of torn oxide defects.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.737-740
• /
• 2001

This paper describes the fabrication and characteristics of CrN thin-film type pessure sensors, which the sensing elements were deposited on SUS. 630 diaphragm by DC reactive magnetron sputtering in an argon-nitride atmosphere(Ar-(10%)N$_2$). The optimized condition of CrN thin-film sensing elements was thickness range of 3500${\AA}$ and annealing condition(300$^{\circ}C$, 3 hr) in Ar-10 %N$_2$deposition atmosphere. Under optimum conditions, the CrN thin-films for strain gauges is obtained a high resistivity, $\rho$=1147.65 ${\mu}$$\Omega$cm, a low temperature coefficient of resistance, TCR=-186 ppm/$^{\circ}C$ and a high temporal stability with a good longitudinal, 11.17. The output sensitivity of fabricated CrN thin-film type pressure sensors is 2.36 mV/V, 4∼20 mA and the maximum non-linearity is 0.4 %FS and hysteresis is less than 0.2 %FS.

• Proceedings of the KIEE Conference
• /
• 1998.11c
• /
• pp.723-725
• /
• 1998

STI CMP process are substituting gradually for LOCOS(Local Oxidation of Silicon) process to be available below sub-0.5um technology and to get planarized. The other hand, STI CMP process(especially STI CMP with RIE etch back process) has some kinds of defect like Nitride residue, Torn Oxide defect, etc. In this paper, we studied how to reduce Torn Oxide defects after STI CMP with RIE etch back process. Although Torn Oxide defects which occur on Oxide on Trench area is not deep and not sever, Torn oxide defects on Moat area is sometimes very deep and makes the yield loss. We did test on pattern wafers witch go through Trench process, APCVD process, and RIE etch back process by using an REC 472 polisher, IC1000/SUV A4 PAD and KOH base slurry to reduce the number of torn defects and to study what is the root causes of torn oxide defects.

• The Journal of Natural Sciences
• /
• v.5 no.2
• /
• pp.75-80
• /
• 1992

The objective of this study is to investigate the effect of dispersion of silicon nitride powder with 5wt% $A1_2$$O_3$ and 5wt% $Y_2$$O_3$ on the microstructure of a sintered body. $Si_3$$N_4$ powder was dispered in a distilled water with varing pH.Zeta potential was measured and the dispersion states were directly observed by SEM. Green bodies were obtained by slip-casting and fired at $1750^{\circ}C$ for 1 hr. Microstructures of fired specimens were observed by SEM. The result were that the specimen prepared from the dispersions with pH 5 and 10 showed the best densification.

• Journal of the Semiconductor & Display Technology
• /
• v.12 no.1
• /
• pp.29-33
• /
• 2013

We have fabricated transparent polymer composite films with high thermal emissivity, which can be used for heat dissipation of transparent electronics. PMMA (poly(methyl methacrylate)) solution with high transparency and thermal emissivity is mixed with various fillers (carbon nanotubes (CNTs), aluminum nitride (AlN), or silicon carbide (SiC)) with high thermal conductivity. We have achieved the thermal emissivity as high as 0.94 by the addition of CNTs. Compared with the PMMA film on glass, however, the addition of AlN or SiC is shown to rather decrease the thermal emissivity. It is also observed that the thickness of the PMMA film does not affect its thermal emissivity. To avoid any degradation of the thermal conductivity, therefore, the PMMA film thickness is desirable to be $1{\mu}m$. There also exists a tradeoff between the optical transmittance and thermal conductivity on the selection of the amount of fillers.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.20.2-20.2
• /
• 2011

III-nitrides have attracted much attention for optoelectronic device applications whose emission wavelengths ranging from green to ultraviolet due to their wide band gap. However, due to the strong polarization properties of conventional c-plane III-nitrides, the built-in polarization-induced electric field limits the performance of optical devices. Therefore, there has been a renewed interest in the growth of nonpolar III-nitride semiconductors for polarization free heterostructure optoelectronic and electronic devices. However, the crystal and the optical quality of nonpolar/semipolar GaN have been poorer than those of conventional c-plane GaN, resulting in the relative poor optical and electrical properties of light emitting diodes (LEDs). In this presentation, I will discuss the growth and characterization of high quality nonpolar a-plane and semipolar (11-22) GaN and InGaN multiple quantum wells (MQWs) grown on r- and m-plane sapphire substrates, respectively, by using metalorganic chemical vapor deposition (MOCVD) without a low temperature GaN buffer layer. Especially, the epitaxial lateral overgrowth (ELO) technique will be also discussed to reduce the dislocation density and enhance the performance of nonpolar and semipolar GaN-based LEDs.

• Tribology and Lubricants
• /
• v.23 no.1
• /
• pp.14-18
• /
• 2007

SCM415 alloy was implanted with nitrogen ions using plasma source ion implantation (PSII), at a dose range of $1{\times}10^{17}\;to\;6{\times}10^{17}N^{+}cm^{-2}$. Auger electron spectrometry (AES) was used to investigate the depth profile of the implanted layer. Friction and wear tests were carried out on a block-on-ring wear tester. Scanning electron microscopy (SEM) was used to observe the micro-morphology of the worn surface. The results revealed that after being implanted with nitrogen ions, the frictional coefficient of the surface layer decreased, and the wear resistance increased with the nitrogen dose. The tribological mechanism was mainly adhesive, and the adhesive wear tended to become weaker oxidative wear with the increase in the nitrogen dose. The effects were mainly attributed to the formation of a hard nitride precipitate and a supersaturated solid solution of nitrogen in the surface layer.

• Electronics and Telecommunications Trends
• /
• v.29 no.6
• /
• pp.53-62
• /
• 2014

본고는 최근 화두가 되고 있는 에너지 절감을 위해 고효율, 친환경의 WBG(Wide Band-Gap) 화합물반도체인 SiC(Silicon Carbide), GaN(Gallium Nitride) 전력반도체 소자 및 전력변환 모듈의 기술동향과 ETRI에서 연구개발 진행 중인 GaN 전력반도체 관련 기술에 대해 기술한다. WBG 전력반도체는 기존의 실리콘 전력반도체와 비교하여 열 특성 향상, 고속 스위칭, 고전압/고전류 특성 및 스위칭 손실 최소화 등이 가능하고 이에 따른 시스템의 소형화 및 전력효율 향상 효과를 얻을 수 있다. 특히, GaN 전력반도체 소자는 시장이 가장 넓게 형성되어 있는 900V 이하에 적용이 가능하며, 앞으로 시장이 커질 것으로 예상되는 HEV(Hybrid Electric Vehicle)/EV(Electric Vehicle)의 친환경 자동차에도 활용될 것으로 기대되고 있다. 본고는 최근의 일본과 미국에서의 WBG 전력반도체에 대한 관심 및 투자 방향과 GaN 전력반도체 소자에 대한 해외 기업의 업계동향에 대해서도 함께 살펴본다. 이러한 WBG 전력반도체에 대한 해외 선진업체의 산업동향과 더불어 ETRI에서 연구개발 중인 GaN 전력반도체 기술현황에 대해 전력소자 설계 및 제조공정, 패키징, 전력모듈 설계 제작 기술을 포함하여 기술한다.