• 한국분말재료학회지
• /
• 제18권3호
• /
• pp.250-255
• /
• 2011

The potential application of ultrafine cerium oxide (ceria, $CeO_2$) as an oxygen gas sensor has been investigated. Ceria was synthesized by a thermochemical process: first, a precursor powder was prepared by spray drying cerium-nitrate solution. Heat treatment in air was then performed to evaporate the volatile components in the precursor, thereby forming nanostructured $CeO_2$ having a size of approximately 20 nm and specific surface area of 100 $m^2/g$. After sintering with loosely compacted samples, hydrogen-reduction heat treatment was performed at 773K to increase the degree of non-stoichiometry, x, in $CeO_{2-x}$. In this manner, the electrical conductivity and oxygen-response ability could be enhanced by increasing the number of oxygen vacancies. After the hydrogen reduction at 773K, $CeO_{1.5}$ was obtained with nearly the same initial crystalline size and surface. The response time $t_{90}$ measured at room temperature was extremely short at 4 s as compared to 14 s for normally sintered $CeO_2$. We believe that this hydrogen-reduced ceria can perform capably as a high-performance oxygen sensor with good response abilities even at room temperature.

• Carbon letters
• /
• 제4권4호
• /
• pp.168-174
• /
• 2003

Silver nitrate ($AgNO_3$) powder was mixed into a reformed pitch precursor. Then, the silver-containing pitch was melt spun to form round and "C" shape fibers. A wire mesh was inserted prior to the nozzle to improve the spinnability of the silvercontaining precursor pitch. Silver particles in the carbon fibers (CFs) were detected by XRD and TEM. These tests showed that silver particles were uniformly distributed and the total amount of silver remained constant during stabilization and carbonization. Next, the silver-containing CFs were activated by steam diluted in nitrogen gas. Silver particles accelerated the activation rate, but the specific surface areas of the silver-containing ACFs were similar to those of non-silver containing ACFs at the same burn-off levels. The specific surface area of the C-shaped activated carbon fibers was larger than that of the round activated carbon fibers. The likely reason is that the surface area of a C-shaped CF is about two times larger than that of a round CF when equivalent cross-sectional areas are compared. A small amount of silver particles in the periphery of the CFs was removed during the activation, but the remainder of silver was stayed within the ACFs.

• Bulletin of the Korean Chemical Society
• /
• 제35권10호
• /
• pp.2917-2921
• /
• 2014

Cerium-activated yttrium aluminate ($Y_3Al_5O_{12}:Ce^{3+}$) exhibiting a garnet structure has been widely utilized in the production of light emitting diodes (LEDs) as a yellow emitting phosphor. The commercialized yttrium aluminum garnet (YAG) phosphor is typically synthesized by a solid-state reaction, which produces irregular shape particles with a size of several tens of micrometers by using the top-down method. To control the shape and size of particles, which had been the primary disadvantage of top-down synthetic methods, we synthesized YAG:Ce nanoparticles with a diameter of 500 nm using a coprecipitation method under the atmospheric pressure without the use of template or special equipment. The precursor particles were formed by refluxing an aqueous solution of the nitrate salts of Y, Al, and Ce, urea, and polyvinylpyrrolidone (55 K) at $100^{\circ}C$ for 12 h. YAG:Ce nanoparticles were formed by the calcination of precursor particles at $1100^{\circ}C$ for 10 h under atmospheric conditions. The phase identification, microstructure, and photoluminescent properties of the products were evaluated by X-ray powder diffraction, scanning electron microscopy, absorption spectrum and photoluminescence analyses.

• 마이크로전자및패키징학회지
• /
• 제22권3호
• /
• pp.45-50
• /
• 2015

Glycine-nitrate와 citric acid를 이용하여 단상의 Ni-Zn ferrite, Ba-ferrite 나노입자와 두 나노복합체 ferrite의 전구체를 제조하고 이를 열처리하여 XRD 및 FT-IR로 각각의 상 분석을, SEM으로 분말의 형상과 크기를, VSM으로 자기적 특성과 합성된 나노복합체 ferrite에서의 exchange-coupling 상호작용을 확인하였다. XRD 분석 결과, 자전 연소법으로 얻은 전구체로 단상의 Ni-Zn ferrite와 Ba-ferrite 나노 입자 및 $BaFe_{12}O_{19}/Ni_{0.5}Zn_{0.5}Fe_2O_4$ 나노복합체 페라이트가 합성되었으며, 나노복합체에는 $BaFe_{12}O_{19}$와 $Ni_{0.5}Zn_{0.5}Fe_2O_4$가 잘 분포되어 있어 경자성과 연자성이 공존하고 있음을 확인하였고, 나노복합체 페라이트의 히스테리시스 곡선의 형상을 통해 경자성과 연자성 사이에 exchange-copuling이 잘 이루어졌음을 확인할 수 있었다. VSM으로 측정한 나노복합체의 경우. GNP로 제조한 precursor를 $900^{\circ}C$에서 하소한 $BaFe_{12}O_{19}/Ni_{0.5}Zn_{0.5}Fe_2O_4$ 나노복합체는 포화자화 81.69 emu/g, 잔류자화 38 emu/g, 보자력 2598.48G를 나타내었다. $Ni_{0.5}Zn_{0.5}Fe_2O_4/BaFe_{12}O_{19}$ 복합체에서 $BaFe_{12}O_{19}$의 무게비가 증가 할수록 보자력은 증가하였고, 포화자화값과 잔류자화 값은 감소하였다.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2006년도 추계학술대회
• /
• pp.360-363
• /
• 2006

We synthesized $(La,\;Sr)MnO_{3+{\delta}$ as a cathode for SOFC by glycine nitrate process(GNP) and knew the different properties of $(La_{1-x}Sr_x)MnO_3$ by using nitrate solution and oxide solution as starting material. In case of using nitrate solution as a starting material, main crystal phase peak of $LaMnO_3$ increased as Sr content added up and a peak of $Sr_2MnO_4\;and\;La_2O_3$ was showed as a secondary phase. We added Mn excess to control a crystal phase. In this case, the electrical conductivity had a high value 210.3S/cm at $700^{\circ}C$ On the other side, when we used oxide solution as a starting material, we found main crystal phase of $LnMnO_3$ to increase as Sr content added up and a peak of $La_2O_3$ as a secondary phase. Similary, we added Mn excess to control a crystal phase in this case. We knew $(La,\;Sr)MnO_3$ powder to sinter well and the electrical conductivity of the sintered body at $1200^{\circ}C$ for 4hrs was 152.7s/cm at $700^{\circ}C$. The sintered $(La,\;Sr)MnO_3$ powder at $1000^{\circ}C$ for 4hrs got the deoxidization peak, depending on the temperature md in case of using nitrate solution as a start ing material the deoxidization peak was showed at $450^{\circ}C$ which is lower than used a oxide solution as a starting material. As a result, when $(La,\;Sr)MnO_3$ powder was synthesized to add Mn excess and to use nitrate solution as a starting material, we found it to have the higher deoxidization property and considered it as a cathode for m properly. And we found it to have different electrical conduct ivity the synthesized $(La,\;Sr)MnO_3$ powder by using different start ing materials like nitrate solution and oxide solution which influence a sintering density and crystal phase.

• Korean Chemical Engineering Research
• /
• 제54권3호
• /
• pp.299-304
• /
• 2016

Nitrate-citrate 혼합 전구체로부터 ZnO 입자 합성을 위한 자체진행 반응(Self-propagating reaction)의 특성을 고찰하였다. 질화물과 Citrate 그룹간의 자체진행 반응을 위해 탄소/질소 성분의 비는 0.7~0.8 수준으로 유지하였으며, 출발물질의 시료를 TGA방법에 의해 열분해하였다. 반응의 후반부인 반응 전환율이 0.5 이상에서 자체진행 반응의 특성을 나타내었으며 시료는 매우 짧은 시간에 많은 열을 방출하며 분해되었다. 반응의 전반부(X<0.5)가 전체반응의 율속단계로 나타났으며, 이 율속단계에서 반응의 특성을 Friedman, Ozawa-Flynn-Wall 그리고 Vyazovkin의 방법들을 사용하여 해석하였다. 율속단계에서 활성화 에너지는 46~130 (kJ/mol)의 범위로 반응 전환율이 증가함에 따라 증가하였으며, 반응차수는 2.9~0.9, 그리고 반응속도의 빈도인자(Frequency factor)는 85~278 ($min^{-1}$)의 범위에서 승온속도가 증가함에 따라 각각 전자는 감소하고 후자는 증가하였다.

• 한국식품위생안전성학회지
• /
• 제13권4호
• /
• pp.406-411
• /
• 1998

조리방법이 시판 햄 및 소시지의 NA 생성에 미치는 영향을 조사하기 위해 가스레인지 (GR), 전자레인지 (ER) 및 데친 후 전자레인지(BE)로 조리하였을 때 생성되는 NA를 GC-TEA로 분석하였고, 동시에 NA 생성에 영향을 미칠 것으로 판단된 질산염 및 아질산염도 분석하였다. 조리 전 햄의 질산염 및 아질산염질소의 함량은 각각 2.0, 1.8mg/kg이었으나 조리과정 중 단일 햄에서는 미량 증가하였고, 혼합햄에서 질산염질소는 감소하였으나 아질산 염질소는 증가하였다. 소시지의 질산염 및 아질산염 질소는 각각 1.8, 0.9mg/kg이었으며 조리과정 중 질산염질소는 감소한 반면 아질산염질소는 미량 증가하였다. 햄과 소시지 모두에서 NA는 NDMA만이 검출되었는데 조리방법에 관계없이 모두 조리과정 중 증가하는 경향을 보였고 가스레인지로 조리한 경우는 평균 6.0~70.7배, 전자레인지 및 데친후 전자레인지로 조리한 경우는 각각 평균 2.4~39~2, 7.0~56.3배 증가하였다.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2004년도 Asia Display / IMID 04
• /
• pp.1079-1082
• /
• 2004

Dense $BaMgAl_{10}O_{17}:Eu^{2+}$ phosphor particles with a spherical shape have been synthesized through spray pyrolysis method using basic aluminum nitrate precursor as a spray solution. Also, a thin layer of silica on the surface of $BaMgAl_{10}O_{17}:Eu^{2+}$ particles were coated by hydrolysis reaction of alkoxide sources with the particles. The correlation between PL intensity and surface treatment by coating for the dense $BaMgAl_{10}O_{17}:Eu^{2+}$ particles have been investigated.

• 한국분말재료학회지
• /
• 제18권4호
• /
• pp.332-339
• /
• 2011

Cemented tungsten carbide has been used in cutting tools and die materials, and is an important industrial material. When the particle size is reduced to ultrafine, the hardness and other mechanical properties are improved remarkably. Ultrafine cemented carbide with high toughness and hardness is now widely used. The objective of this study is synthesis of nanostructured WC-Co powders by liquid phase method of tungstate. The precursor powders were obtained by freezen-drying of aqueous solution of soluble salts, such as ammonium metatungstate, cobalt nitrate. the final compositions were WC-10Co. In the case of liquid phase method, it can be observed synthesis of WC-10Co. The properties of powder produced at various temperature, were estimated from the SEM, BET and C/S analyser.

• 한국전기전자재료학회논문지
• /
• 제30권7호
• /
• pp.413-416
• /
• 2017

We investigated solution-processed indium-yttrium-oxide (IYO) TFTs using apoly (methyl methacrylate) (PMMA) passivation layer. The IYO semiconductor solution was prepared with 0.1 M indium nitrate hydrate and 0.1 M yttrium acetate dehydrate as precursor solutions. The solution-processed IYO TFTs showed good performance: field-effect mobility of $13.13cm^2/Vs$, a threshold voltage of 8.2 V, a subthreshold slope of 0.93 V/dec, and a current on-to-off ratio of $7.2{\times}10^6$. Moreover, the PMMA passivation layers used to protectthe IYO active layer of the TFTs, did so without deteriorating their performance under ambient conditions; their operational stability and electrical properties also improved by decreasing leakage current.