• Resources Recycling
• /
• v.22 no.3
• /
• pp.43-49
• /
• 2013

A study on the recovery of lithium and leaching behavior of NCM powder by hydrogen reduction for NCM system Li-ion battery scraps was investigated. The reductive rate was about 93% at $800^{\circ}C$ by hydrogen treatment. The lithium carbonate with 99% purity was manufactured by using $CO_2$ gas and washing method with water for NCM powder after hydrogen reduction. As a result of comparing the powders before and after the hydrogen reduction treatment for acid leaching behavior we obtained 32% enhanced leaching rate of cobalt, 45% enhanced leaching rate of nickel and the 90% leaching effect for manganese by hydrogen reduction at 2M $H_2SO_4$ concentration condition.

• Korean Journal of Materials Research
• /
• v.30 no.5
• /
• pp.231-238
• /
• 2020

The composition of martensite transformation in NiAl alloy is determined using pure nickel and aluminum powder by vacuum hot press powder metallurgy, which is a composition of martensitic transformation, and the characteristics of martensitic transformation and microstructure of sintered NiAl alloys are investigated. The produced sintered alloys are presintered and hot pressed in vacuum; after homogenizing heat treatment at 1,273 K for 86.4 ks, they are water-cooled to produce NiAl sintered alloys having relative density of 99 % or more. As a result of observations of the microstructure of the sintered NiAl alloy specimens quenched in ice water after homogenization treatment at 1,273 K, it is found that specimens of all compositions consisted of two phases and voids. In addition, it is found that martensite transformation did not occur because surface fluctuation shapes did not appear inside the crystal grains with quenching at 1,273 K. As a result of examining the relationship between the density and composition after martensitic transformation of the sintered alloys, the density after transformation is found to have increased by about 1 % compared to before the transformation. As a result of examining the relationship between the hardness (Hv) at room temperature and the composition of the matrix phase and the martensite phase, the hardness of the martensite phase is found to be smaller than that of the matrix phase. As a result of examining the relationship between the temperature at which the shape recovery is completed by heating and the composition, the shape recovery temperature is found to decrease almost linearly as the Al concentration increases, and the gradient is about -160 K/at% Al. After quenching the sintered NiAl alloys of the 37 at%Al into martensite, specimens fractured by three-point bending at room temperature are observed by SEM and, as a result, some grain boundary fractures are observed on the fracture surface, and mainly intergranular cleavage fractures.

• Resources Recycling
• /
• v.22 no.4
• /
• pp.62-69
• /
• 2013

A study on the recovery of lithium and leaching behavior of NCM powder by carbon reduction for NCM-system Li-ion battery scraps was conducted. First of all, the oxide powders of NCM-system with layer structure were decomposed by carbon, lithium was converted to lithium carbonate by carbon reaction at above $600^{\circ}C$. The lithium carbonate powders with 99% purity were manufactured by washing method with water and concentration process for NCM powder after carbon reduction. The reaction yield was approximately 88% at $800^{\circ}C$ by carbon reduction. At this time, leaching efficiency at 2M sulfuric acid concentration was over 99% for cobalt, nickel and manganese.

• Journal of Powder Materials
• /
• v.26 no.3
• /
• pp.231-236
• /
• 2019

Ni hydroxides ($Ni(OH)_2$) are synthesized on Ni foam by varying the hexamethylenetetramine (HMT) concentration using an electrodeposition process for pseudocapacitor (PC) applications. In addition, the effects of HMT concentration on the $Ni(OH)_2$ structure and the electrochemical properties of the PCs are investigated. HMT is the source of amine-based $OH^-$ in the solution; thus, the growth rate and morphological structure of $Ni(OH)_2$ are influenced by HMT concentration. When $Ni(OH)_2$ is electrodeposited at a constant voltage mode of -0.85 V vs. Ag/AgCl, the cathodic current and the number of nucleations are significantly reduced with increasing concentration of HMT from 0 to 10 mM. Therefore, $Ni(OH)_2$ is sparsely formed on the Ni foam with increasing HMT concentration, showing a layered double-hydroxide structure. However, loosely packed $Ni(OH)_2$ grains that are spread on Ni foam maintain a much greater surface area for reaction and result in the effective utilization of the electrode material due to the steric hindrance effect. It is suggested that the $Ni(OH)_2$ electrodes with HMT concentration of 7.5 mM have the maximum specific capacitance (1023 F/g), which is attributed to the facile electrolyte penetration and fast proton exchange via optimized surface areas.

• Journal of the Korean Ceramic Society
• /
• v.35 no.3
• /
• pp.273-279
• /
• 1998

Unite cell of soid oxide fuel cell (SOFC) that consists of a dense yttria-stabilized zirconia(YSZ) electrolyte a porous nickel-YSZ cermet anode and a porous strontium- doped lanthanum manganate(LSM) cathod was fabricated from using pore former through co-firing technique. Initial sintering shrinkage rates of each layer were identified for fabricating SOFC. Heterogenous sintering was very effective in tailoring shrinkage rate for three layers. The powder tailoring necessary for shrinkage rate matching are as follows ; electrolyte of 60% TZ8YS/ 40% TZ8Y mixture anode of 51wt% NiO/49 wt% (70wt% TZ8YS/30 wt% UT ZrO2) mixture and cathode of 80% LSM/20% UT ZrO2 mixture . The overall sintering shrinkage rate differences of three layers using these compositions were maintained in a few percent.

• Journal of the Korean Ceramic Society
• /
• v.30 no.6
• /
• pp.429-432
• /
• 1993

Cr3C2 material is characterized by high chemical stability and poor sinterability with low strength [50~150MPa]. In his study, low melting temperature nickel powder was used to improve sinterability as well as strength. In addition, molydenum particles were added to the Ni-bonded Cr3C2 cermet pseudomatrix to increase resistance to fracture. The specimens made by hot-pressing under vacuum and strength was measured by 4-point bending. Indentation cracking and fractographic examination were conducted to study the interaction of the indentation cracks with the reinforcing particles. Toughening mechanisms and failure will be discussed in terms of crack/particle interactions and compared with previous works.

• Journal of the Korean Electrochemical Society
• /
• v.10 no.2
• /
• pp.88-93
• /
• 2007

Nano-sized Sn particles were coated with Ni-P layer using an electroless deposition method and their anodic performance was tested for lithium secondary batteries. Uniform coating layers were obtained, of which the thickness was controlled by varying the $Ni^{2+}$ concentration in the plating bath. It was found that the Ni-P layer plays two important roles in improving the anodic performance of Sn powder electrode. First, it prevents the inter-particle aggregation between Sn particles during the charge/discharge process. Second, it provides an electrical conduction pathway to the Sn particles, which allows an electrode fabrication without an addition of conductive carbon. A pseudo-optimized sample showed a good cyclability and high capacity ($>400mAh\;g^{-1}$) even without conductive carbon loading.

• Journal of the Korean Chemical Society
• /
• v.13 no.4
• /
• pp.309-312
• /
• 1969

A series of metal ion-2, 5-diamine 1, 4-dihydroxybenzene polymers containing copper(II), nickel(II) or cobalt (II) have been prepared. The structure was postulated on the basis of elementary analysis of polymers. It was found that copper polymer is most likely the coordination polymers by X-ray powder pattern studies. The thermal stability of the polymers was also studied by a simple method, utilizing a thermogravimetric balance. The order of thermal stabilities is Cu(II) > Ni(II) > Co(II). The polymers start to decompose at a relatively low temperature.

• Transactions of Materials Processing
• /
• v.29 no.6
• /
• pp.307-315
• /
• 2020

The cemented carbide and stainless steel were bonded using a hot-vacuum brazing method to analyze the bonding interface. Since it is suitable for the hot vacuum brazing, nickel metal was used as a binder among the main components of the cemented carbide, and a new cemented carbide material was developed by adjusting the alloy composition. The paste, which is one of the important factors affecting the hot vacuum brazing bonding, was able to improve brazing adhesion by mixing solder as Ni powder and a binder as an organic compound at an appropriate ratio. Division of the stainless steel yielded a dense brazing result. This study elucidated the interfacial characteristics of wear-resistant parts by bonding stainless steel and cemented carbide via hot vacuum brazing.

• Korean Journal of Materials Research
• /
• v.8 no.5
• /
• pp.444-449
• /
• 1998

There are various shielding materials that have been considered; the use of a metallic plate or the layering of a conductive material on a plastic surface and the insertion of filler in plastics. All of these methods have shown their merits and weakness. Therefore, many studies have concentrated on developing materials that effectively cut down EMI without increase in weights of housing materials. In these respects, this study has focused on investigations of the shielding effect of materials that have electroless nickel plating on the lamella structured micro particles surface with low specific gravity. When a film of electroless nickel were plated on a micro particle surfaces and then mixed with paint, the electromagnetic shielding effects were measured as 63dB. Although these effects were less than that 90dB of the copper plate, trials in a series of 6 times increased the shielding effect by IOdB and is applicable to wide range of EMI shielding.