• Journal of the Korean Society of Safety
• /
• v.32 no.3
• /
• pp.160-171
• /
• 2017

US national research laboratories developed the first Vital Area Identification (VAI) method for the physical protection of nuclear power plants that is based on Event Tree Analysis (ETA) and Fault Tree Analysis (FTA) techniques in 1970s. Then, Korea Atomic Energy Research Institute proposed advanced VAI method that takes advantage of fire and flooding Probabilistic Safety Assessment (PSA) results. In this study, in order to minimize the burden and difficulty of VAI, (1) a set of streamlined VAI rules were developed, and (2) this set of rules was applied to PSA fault tree and event tree at the initial stage of VAI process. This new rule-based VAI method is explained, and its efficiency and correctness are demonstrated throughout this paper. This new rule-based VAI method drastically reduces problem size by (1) performing PSA event tree simplification by applying VAI rules to the PSA event tree, (2) calculating preliminary prevention sets with event tree headings, (3) converting the shortest preliminary prevention set into a sabotage fault tree, and (4) performing usual VAI procedure. Since this new rule-based VAI method drastically reduces VAI problem size, it provides very quick and economical VAI procedure. In spite of an extremely reduced sabotage fault tree, this method generates identical vital areas to those by traditional VAI method. It is strongly recommended that this new rule-based VAI method be applied to the physical protection of nuclear power plants and other complex safety-critical systems such as chemical and military systems.

• Smart Structures and Systems
• /
• v.14 no.5
• /
• pp.847-867
• /
• 2014

There are continuous efforts to mitigate structural losses from earthquakes and manage risk through seismic risk assessment; seismic fragility curves are widely accepted as an essential tool of such efforts. Seismic fragility curves can be classified into four groups based on how they are derived: empirical, judgmental, analytical, and hybrid. Analytical fragility curves are the most widely used and can be further categorized into two subgroups, depending on whether an analytical function or simulation method is used. Although both methods have shown decent performances for many seismic fragility problems, they often oversimplify the given problems in reliability or structural analyses owing to their built-in assumptions. In this paper, a new method is proposed for the development of seismic fragility curves. Integration with sophisticated software packages for reliability analysis (FERUM) and structural analysis (ZEUS-NL) allows the new method to obtain more accurate seismic fragility curves for less computational cost. Because the proposed method performs reliability analysis using the first-order reliability method, it provides component probabilities as well as useful byproducts and allows further fragility analysis at the system level. The new method was applied to a numerical example of a 2D frame structure, and the results were compared with those by Monte Carlo simulation. The method was found to generate seismic fragility curves more accurately and efficiently. Also, the effect of system reliability analysis on the development of seismic fragility curves was investigated using the given numerical example and its necessity was discussed.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2000.11b
• /
• pp.287-294
• /
• 2000

Calculation of the flexural rigidity value (EI) is indispensable for prescription of deflection characteristics of crop stalks in harvesting□Conventionally□EI has been determined by either average EI of the whole stalk or average EI of each stems divided into node through the calculation method of cantilever with homogeneous section□However□deflection characteristics of crop stalks caused by mechanical operation such as combine harvester were not exactly presumed by these conventional EI through the experiment by authors. Further, actual EI of a stalk changes in company with a change of moisture contents as time passes during the experiment. Finally, efficient calculation method for determining EI is needed in order to improve these problems. In this study, mechanical model based on actual structure of the crop stalk with variety sectional area was proposed. This mechanical model is calculated by the theory of cantilever with continuous stages. Therefore, improvement of both calculating accuracy on EI and efficiency of measuring system was tried. At first, this calculation method was applied to piano wire of which EI was recognized in advance. As a result, EI calculated from this new method coincided approximately with piano wire's EI. Next, applying to crop stalks as same as piano wire, relationship between loads acting on crop stalks and deflection values calculated by EI using this new calculation method was exactly presumed in comparison with conventional method. Further, measuring time of deflection test was greatly reduced. Finally, new calculation method of EI will be available for estimating mechanical characteristics of so many kinds of crop stalks in harvesting operation. Further, in this study, new deflection test using image-processing apparatus by computer will be introduced.

• Structural Engineering and Mechanics
• /
• v.13 no.5
• /
• pp.557-568
• /
• 2002

For the evaluation of the capability of a tubular member of an offshore structure to absorb the collision energy, a simple method can be employed for the collision analysis without performing the detailed analysis. The most common simple method is the rigid-plastic method. However, in this method any characteristics for horizontal movement and rotation at the ends of the corresponding tubular member are not included. In a real structural system of an offshore structure, tubular members sustain a certain degree of elastic support from the adjacent structure. End fixity has influences in the behaviors of a tubular member. Three-dimensional FEM analysis can include the effect of end fixity fully, however in viewpoints of the inherent computational complexities of the 3-D approach, this is not the recommendable analysis at the initial design stage. In this paper, influence of end fixity on the behaviors of a tubular member is investigated, through a new approach and other approaches. A new analysis approach that includes the flexibility of the boundary points of the member is developed here. The flexibility at the ends of a tubular element is extracted using the rational reduction of the modeling characteristics. The property reduction is based on the static condensation of the related global stiffness matrix of a model to end nodal points of the tubular element. The load-displacement relation at the collision point of the tubular member with and without the end flexibility is obtained and compared. The new method lies between the rigid-plastic method and the 3-demensional analysis. It is self-evident that the rigid-plastic method gives high strengthening membrane effect of the member during global deformation, resulting in a steeper slope than the present method. On the while, full 3-D analysis gives less strengthening membrane effect on the member, resulting in a slow going load-displacement curve. Comparison of the load-displacement curves by the new approach with those by conventional methods gives the figures of the influence of end fixity on post-yielding behaviors of the relevant tubular member. One of the main contributions of this investigation is the development of an analytical rational procedure to figure out the post-yielding behaviors of a tubular member in offshore structures.

• Journal of Environmental Impact Assessment
• /
• v.16 no.4
• /
• pp.301-310
• /
• 2007

For the improvement of air quality in the metropolitan area, Korea has enforced the air pollutant emission cap regulation from the 1st of July, 2007, and the companies that intend to install a new or an enlarged facility in the metropolitan area will be restricted. However, the current regulation on permission does not describe a standard of judgement distinctly. In this study, therefore, a method of permission on the installation of a new or an enlarged facility was developed by supplementing the law in force based on the foreign cases. To develop a specific permit regulation and procedure, the developed nations' cases such as US, Canada, EU were reviewed thoroughly. Also, an appropriate method was suggested to apply domestically for a new or an enlarged facility permit within the regulations of the metropolitan special law. The method consists of first, calculating the possible permit quantity from the difference between an estimated annual emission cap and the annual emission provided by the implementation plan in each region. Second, permitting a new or an enlarged facility construction within the difference of the emission between the regional emission cap and the implementation plan in 2014. Third, distributing emissions allowable to each performance year based on the regional emission cap and the implementation plan in 2014. Fourth, making use of the emission difference between the implementation plan and the performance result in each year. Considering the general domestic conditions, the convenience of the permit authority and permitted companies, the most reasonable method was to use the fourth. To enforce the suggested permit method in a more flexible way, parts of the related regulations need to be revised and continuous research and analysis on the results from the implemented system and on foreign cases is necessary to develop this method a suitable system for domestic conditions and to settle the air pollutant emission cap system.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.23 no.3
• /
• pp.237-242
• /
• 2014

Recently much research are has been done into the compositions of lead-free solders. As a result, there has been a rapid increase in the number of new compositions. In the past, the properties of these new compositions were determined and verified through drop-impact tests. However, these drop tests were expensive and it took a long time to obtain a result. The main goal of this study was to establish an analytical method capable of predicting the impact life-time of a new solder composition for board-level flip chips though the application of drop simulations using LS-DYNA. Based on the reaction load obtain with LS-DYNA, the drop-impact fracture cycles were predicted. The study was performed using a Sn-3.0Ag-0.5Cu solder (305 composition). To verify the reliability of the proposed analytical method, the results of the drop-impact tests and life-time analysis were compared, and were found to be in good agreement. Thus, the new analytical method was shown to be very useful and effective.

• The Transactions of the Korea Information Processing Society
• /
• v.6 no.4
• /
• pp.999-1008
• /
• 1999

In this study, we propose a new multi-party electronic approval system. We classified and analyzed several existing electronic approval systems which use the multisignature method. Based on the analysis, we developed a new multisignature method and then applied it to several existing electronic approval systems. By comparing various aspects of the new and the conventional methods, we were able to demonstrate the effectiveness of the proposed method. The new method is based discrete logarithm so that it lowers the complexity requirement involved in electronic communication and rises the ability requirement, hence makes itself suitable to general electronic approval systems.

• Journal of the Korean Data and Information Science Society
• /
• v.22 no.5
• /
• pp.931-940
• /
• 2011

Classification is to generate a rule of classifying objects into several categories based on the learning sample. Good classification model should classify new objects with low misclassification error. Many types of classification methods have been developed including logistic regression, discriminant analysis and tree. This paper presents a new classification method using penalized partial least squares. Penalized partial least squares can make the model more robust and remedy multicollinearity problem. This paper compares the proposed method with logistic regression and PCA based discriminant analysis by some real and artificial data. It is concluded that the new method has better power as compared with other methods.

• Journal of the Korean Institute of Rural Architecture
• /
• v.8 no.1
• /
• pp.17-24
• /
• 2006

The purpose of this study is to provide the systematic report and analysis about Apartment VE application in Design Phase. In this study, the method of VE application is classified into foure groups-changing materials, changing a method of construction, acceptance of new technology, and use of new device. The facts found in this study can be summarized as follows. Application rate of VE is highest in building circumference parts. The main reason would be that there are many applicable factors according to locations, types of work, etc. Parking lots also show similar results with the same reason. It means there are a lot of possibility to adapt value engineering in these steps during the work. So far application of value engineering has been so limited that just small changes of process or method have been tried. One reason is the lack of challenging and the other is some characteristics of construction work which is very difficult to fix after completion. In the future, it would be more efficient to apply new technology and new device in construction work. Though these attempts have been ignored in Korea so far, there are still lots of possibilities to be developed in value engineering.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.19 no.9
• /
• pp.1824-1837
• /
• 1994

Broadband ISDN will support advanced communication services such as multimedia conference, VOD and electronic news service. Because many of these advanced services require multimedia data delivery, future communication networks must have flexible and efficient multiparty communications capabilities. In this paper we propose a new multicasting method which uses packer filtering capabilities both in a physical network and in a logical network layers. This new scheme has potential to reduce the transmission and packet processing overheads of multicast communications. For the new multicasting method, we develop a group matching algorithm which finds a suitable set of groups that covers multiple target hosts. We show the application of the multicasting method and the group matching algorithm with two simple examoles.