• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.210-215
• /
• 2003

A fine hot-wire is used both as a heating element and a temperature sensor in transient hot-wire method. The traditional sensor system is unnecessarily big so that it takes large fluid volume to measure the thermal conductivity. To dramatically reduce this fluid volume, a new sensor fabrication and a data processing method are proposed in this article. Contrast to the conventional and most popular two wire sensor, the new sensor system is made up of divided multiple long and short wires. Through validation experiments, it is found that the measured thermal conductivities of the glycerin are exactly same each other between the conventional and proposed new method. Also some technical considerations in arranging the multiple wires are briefly discussed.

• Tunnel and Underground Space
• /
• v.4 no.3
• /
• pp.237-249
• /
• 1994

A new type of cut method, called SK-cut, was developed in order to overcome the shortcomings of the conventional V-cut and Burn-cut blasting methods. Total 190 times of test blasts were performed for the evaluation of the efficiency of new blasting method. V-cut, Burn cut and SK-cut were compared by applying them to the excavation of main gallery and construction tunnel of underground oil storage cavern. Test results showed that excavation efficiency of the new method was increased by 5.9~9.8% and that specific charge was reduced to 71~92%.

• Journal of the Korean Solar Energy Society
• /
• v.22 no.2
• /
• pp.11-17
• /
• 2002

This paper is concerned with the development of a new method for making, separating ice and storage floated ice by installing an evaporation plate at under-water within a storage tank. In a conventional harvest-type ice storage system, a tank saves ice by separating an ice from an installed evaporation plate, which is located above an ice storage tank as an ice storage system. Developed new harvest-type method shows good heat transfer efficiency than a convectional method. It is because the evaporation panel is directly contacted with water in a storage tank. Also, at a conventional system a circulating pump, a circulating water distributor and a piping are installed, however these components are not necessary in a new method. In this study ice storage systems are experimentally investigated to study the charge and discharge of thermal energy. The results show the applicable possibility and performance enhancement of a new type.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.1
• /
• pp.28-32
• /
• 2013

In this study, we suggested new method for compensation on spring back of press part. At first, we compared between error on CAD data and scanning data. The new method can be substituted for manual modeling process in compensation on spring back. The new method is available for automatic modeling based on 3D scanning data. From the study, the results expect that time and cost reduction for process applying new method for compensation on spring back of press part.

• Advances in Computational Design
• /
• v.4 no.4
• /
• pp.343-365
• /
• 2019

Among the themes related to earthquake countermeasures at construction sites, those for tower cranes are particularly important. An accident involving the collapse of a crane during the construction of a skyscraper has serious consequences, such as human injury or death, enormous repair costs, and significant delays in construction. One of the causes of deadly tower crane collapses is the destruction of the site joints of the tower crane mast. This paper proposes a new design method by static elastoplastic finite element analysis using a supercomputer for the design of the end plate-type tensile bolted joints, which are generally applied to the site joints of a tower crane mast. This new design method not only enables highly accurate and reliable joint design but also allows for a design that considers construction conditions, such as the introduction of a pre-tension axial force on the bolts. By applying this new design method, the earthquake resistance of tower cranes will undoubtedly be improved.

• Korean Journal of Radiology
• /
• v.1 no.3
• /
• pp.142-151
• /
• 2000

Objective: To determine the optimal scan timing for contrast-enhanced magnetic resonance angiography and to evaluate a new timing method based on the arteriovenous circulation time. Materials and Methods: Eighty-nine contrast-enhanced magnetic resonance angiographic examinations were performed mainly in the extremities. A 1.5T scanner with a 3-D turbo-FLASH sequence was used, and during each study, two consecutive arterial phases and one venous phase were acquired. Scan delay time was calculated from the time-intensity curve by the traditional (n = 48) and/or the new (n = 41) method. This latter was based on arteriovenous circulation time rather than peak arterial enhancement time, as used in the traditional method. The numbers of first-phase images showing a properly enhanced arterial phase were compared between the two methods. Results: Mean scan delay time was 5.4 sec longer with the new method than with the traditional. Properly enhanced first-phase images were found in 65% of cases (31/48) using the traditional timing method, and 95% (39/41) using the new method. When cases in which there was mismatch between the target vessel and the time-intensity curve acquisition site are excluded, erroneous acquisition occurred in seven cases with the traditional method, but in none with the new method. Conclusion: The calculation of scan delay time on the basis of arteriovenous circulation time provides better timing for arterial phase acquisition than the traditional method.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.61-64
• /
• 2003

A band function model paired comparison method (BMPC method) is a kind of a paired comparison methods. Considering the human ambiguities, the BMPC method expressing the human judgment characteristics as a monotonous increase function with some width. Since function types are not specified in a BMPC method, the solution is obtained from inequalities, and the solution is given as a domain. To solve the simultaneous inequalities, the sequential renew method is used in the previous BMPC method. However, the sequential renew method requires much computational effort and memories. Generally, in BMPC method, it is able to solve only a paired comparison table which has less 12-13 samples. For that purpose, a new fast solution algorithm is required. In this paper, we proposed a new “search vector method” which renews the solution domain without creating new edge vectors. By using the method, it is able to decrease the necessary memory spaces and time to solve. The proposed method makes it able to solve more than 15 samples paired comparison inspections which are impossible to solve by previous method.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2002.10a
• /
• pp.575-582
• /
• 2002

A new coupling method of Element-Free Galerkin Method(EFGM) and Boundary Element Method(BEM) using the domain decomposition method is presented in this paper. This proposed methodology is that the problem domain is decomposed into sub-domains being modeled by the EFGM and BEM respectively and the respective EFGM and BEM domains share a partially overlapped region over an entire domain. Then, the each sub-domain is separately computed and the variables on common region are iteratively updated until converging. It is an important note that in the developed coupling method, there is no need to combine the coefficient matrices of EFGM and BEM sub-domains, in contrast with the other conventional coupling methods. In the first part of this paper, a theory of EFGM and BEM is summarized, and then a brief introduction of domain decomposition method is described. Then, a new coupling method is presented. Also, patch test and Some numerical examples are studied to verify stability, accuracy and efficiency of the proposed method, in which numerical performance of the method is compared with that of conventional method such as EFGM-BEM variational coupling method, EFGM and BEM.

• Fashion & Textile Research Journal
• /
• v.2 no.4
• /
• pp.353-359
• /
• 2000

The purpose of this study was to develop the jacket pattern drafting method for Korean middle-aged women. The study was composed as follows : 1. Body measurement and statistical analysis : Two hundreds and forty four middle-aged women between the ages of forty five and fifty nine were measured on 52 items. 2. Development of new jacket pattern drafting method : Measurement items necessary to draft new jacket pattern were back waist length, bust girth, waist girth, hip girth, back interscye breadth, front interscye breadth, neck base girth, nipple length, nipple to nipple breadth, 1/2 posterior shoulder length and sleeve length. Basic jackets constructed from the experimental patterns were examined through the fitting test. 3. Evaluation of the new pattern drafting method : The sensory evaluations for appearance and comfort were applied to evaluate the new jacket pattern by comparing it with one of the conventional jacket patterns (Lee Hyung-Suk's). According to the result of sensory evaluation, the new jacket pattern was more positive.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1996.10a
• /
• pp.187-193
• /
• 1996

This paper presents a new approach to modify the traditional method for sampling inspectionby variables to suit undesired measurement conditions. On the basis of a systematic analysis of the effects of measurement errors on different types of acceptance schemes this paper gives two modified equations for revising the sampling size η and the acceptability constant $textsc{k}$ to form a new acceptance scheme (η'$textsc{k}$) under undesired measurement conditions. It has proved that the new method is suitable to different types of sampling inspection by variables including that for mean value and that for percent defective. The new acceptance scheme based on the proposed technique provides an engineering feasibility to replace the traditional scheme to suit undesired measurement conditions.