• Nuclear Engineering and Technology
• /
• v.41 no.6
• /
• pp.821-830
• /
• 2009

In this paper, modal testing and finite element modeling results to identify the modal parameters of a nuclear fuel rod as well as its cladding tube are discussed. A vertically standing full-size cladding tube and a fuel rod with lead pellets were used in the modal testing. As excessive flow-induced vibration causes a failure in fuel rods, such as fretting wear, the vibration level of fuel rods should be low enough to prevent failure of these components. Because vibration amplitude can be estimated based on the modal parameters, the dynamic characteristics must be determined during the design process. Therefore, finite element models are developed based on the test results. The effect of a lumped mass attached to a cladding tube model was identified during the finite element model optimization process. Unlike a cladding tube model, the density of a fuel rod with pellets cannot be determined in a straightforward manner because pellets do not move in the same phase with the cladding tube motion. The density of a fuel rod with lead pellets was determined by comparing natural frequency ratio between the cladding tube and the rod. Thus, an improved fuel rod finite element model was developed based on the updated cladding tube model and an estimated fuel rod density considering the lead pellets. It is shown that the entire pellet mass does not contribute to the fuel rod dynamics; rather, they are only partially responsible for the fuel rod dynamic behavior.

• Journal of Biosystems Engineering
• /
• v.26 no.2
• /
• pp.105-114
• /
• 2001

Modulus of elasticity, modulus of rigidity, damping ratio, and natural frequency of three varieties of boxthorn (Lycium chinense Mill) (Cheongyang #2, Cheongyang gugija, and Cheongyang native) branches were analyzed. Modulus of elasticity and modulus of elasticity and modulus of rigidity of the boxthorn branch was determined using standard formula after simple beam bending and torsion test, respectively, using an universal testing machine. Damping ratio and natural frequency of branches were determined using a system consisted of an accelerometer, a PC equipped with A/D converter, and a software for data analysis. Relationship between the elastic modulus and branch diameter in overall varieties and branch types showed a good correlation (r -0.81). There was, however, no correlation between torsional rigidity and branch diameter. The internal damping results were highly variable and the overall range of the damping ratio of the boxthorn branch was 0.014-0.087, which indicated that the branch was a lightly damped structure. The natural frequency of the boxthorn branch was in the range of 89-363 rad/s for the overall varieties and branch types. A good correlation (r 0.82) existed between the natural frequency and branch diameter in overall varieties and branch type.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08a
• /
• pp.273-276
• /
• 2007

A natural graphite heat spreader increased the upper operating temperature limit of a CCFL backlit LCD television. A 0-80W heat source was used to simulate additional electronics. Without the heat spreader, internal circuitry shut-down at ${\sim}30;$ no shut-down occurred above 80W with a heat spreader. Additionally, brightness, temperature uniformity, and operating ranges were improved, verified by environmental chamber performance testing at various ambient conditions.

• Corrosion Science and Technology
• /
• v.2 no.2
• /
• pp.98-101
• /
• 2003

The Electrical Resistance Probe of carbon steel and weight loss coupons were exposed in atmosphere and in the lake water of Hanoi. The comparison of data received by two methods after one year exposure was presented. The correspondence of the data of these methods on the exposure time in both environments showed a capacity of using Electrical Resistance Probe in Vietnamese natural corrosion testing of Carbon steel.

• Journal of the Korean Geotechnical Society
• /
• v.19 no.4
• /
• pp.133-144
• /
• 2003

The resonant column testing is a laboratory testing method to determine the shear modulus and material damping factor of soils. The method has been widely used for many applications and its importance has increased. Since the first use of the testing method in 1960's, the low-technology electronic devices fir testing and data acquisition have limited the measurement only to the amplitude of the linear spectrum. The limitations of the testing method are also attributed to the assumption of linear-elastic material in the theory of the resonant column testing and also to the incomplete understanding of the dynamic behaviour of the resonant column testing device. Recently, Joh et al. proposed a theory to overcome the limitations of the resonant column testing by deriving the equation of motion and providing its solution for the resonant column testing device. This study proposed the improved data reduction and analysis method for the resonant column testing, thanks to the advanced data acquisition system and the new theoretical solution for the resonant column testing system. For the verification of the proposed data reduction and analysis method, the numerical simulation of the resonant column testing was performed by the finite element analysis. Also, a series of resonant column testing were performed fir Joomunjin sand, which verified the feasibility of the proposed method and revealed the limitations of the conventional data reduction and analysis method.

• Journal of Korean Society of Steel Construction
• /
• v.15 no.2
• /
• pp.117-124
• /
• 2003

Wind-induced motions, like acceleration for instance, often influence designs for high-rise buildings. As a consequence, correct assessment of natural frequency becomes important. The empirical expressions used to quantify this parameter at the design phase tend to yield values that are significantly different from each other. This paper is concerned with the natural periods of steel buildings. It describes the vibration measurement methods that were employed for testing buildings. This paper will also present reliable methods of assessing the natural period from ambient vibration tests. Data from measurements on 21 buildings in Seoul were provided while 21 buildings were tested by ambient vibration measurements to obtain the natural periods. While regression formulas of natural periods for steel-frarried tall buildings were suggested,the obtained formula was compared with the empirical expressions of structural standards and the Eigen-value analysis.

• Proceedings of the KSME Conference
• /
• 2001.11a
• /
• pp.568-572
• /
• 2001

An industrial vibratory conveyor system is devised for large-scale feeding by the low-power, using natural frequency of the system. The important thing in this system is to determine the natural frequency and to drive by it. The purpose of this study is to build up reliance on the system with changing of element parameters for vibration characteristics of balancing type vibratory conveyor by using F.E.M. modeling. For investigating the natural frequency, modal testing is performed by using impact hammer, accelerometer and LMS/Vibration Analysis System. Experimental results are compared with F.E.M results. The results of the comparisons within the errors of less than 2 percent can verify the reliability of the F.E.M. analysis of the system. Also we can verify that the characteristics of natural frequency have linearly decreased(-6%) as adding the mass($50{\sim}600kg$). We can find that controlling driving frequency is necessary for triggering the natural frequency, but natural frequency is less affected by adding the mass on the balancing weight.

• Journal of Korean Association for Spatial Structures
• /
• v.14 no.1
• /
• pp.61-68
• /
• 2014

The design of foot-bridge is often influenced by natural frequency. Consequently, vibration frequency becomes important. The empirical expressions used to quantify this parameter at the design phase have not been developed enough to give guideline to Korean foot-bridge. This paper is concerned with the vertical natural frequency of steel foot-bridges. It describes the vibration measurement methods employed for testing structures and presents reliable methods of assessing natural frequency from jumping vibration tests. Data from measurements on 16 structures in Seoul are given. Regression formulas of natural frequency for steel-framed foot-bridges are suggested. Finally, obtained formula are compared with empirical expressions of Seoul City's guideline.

• Geomechanics and Engineering
• /
• v.22 no.2
• /
• pp.165-171
• /
• 2020

Laboratory determination of strength and deformation behavior of clean sands and gravels has always been challenging due to the difficulty in obtaining their undisturbed samples. An alternative solution to this problem is to develop correlations between mechanical properties of cohesionless soils and their gradation characteristics. This study presents database of 3 natural sands with 11 varying particle size gradation curves to allow investigating relationships between mean particle size, maximum and minimum void ratio, relative density and shear strength of the test soils. Direct shear tests were performed at relative densities of 50, 75 and 95% to explore the effects of gradation and density on the angle of internal friction of the modeled sand samples. It is found that the mean grain size D₅₀ bears good correlations with void ratio range (e_max - e_min) and peak angle of internal friction 𝜙'_peak. The generated regression models are in good agreement with published literature and can be considered as reliable for natural sands in Pakistan. These empirical correlations can save considerable time and efforts involved in laboratory and field testing.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.49 no.1
• /
• pp.20-26
• /
• 2000

This paper deals with the modal analysis and the displacement of stator due to electromagnetic forces in Switched Reluctance Motor(SRM). A free-free model of the stator based on structural 3-dimensional Finite Element Method(FEM) is used for investigation the natural frequencies and the mode shapes of the stator. In addition, The displacement caused by magnetic force acting on stator pole is analyzed by the structural FEM coupled with the magnetic force. From these results, the resonance speed is obtained by the relation of the natural frequencies of the harmonic frequencies of magnetic force. And, the eccentricity with respect to rotor is predicted from the analysis result of the mechanical displacement of stator. The natural frequencies of stator are compared with experimental ones measured by modal testing.