• 대한금속재료학회지
• /
• 제49권5호
• /
• pp.406-410
• /
• 2011

ZnO nanorods were prepared by the electrodeposition route on conductive Au/Si substrates. The effects of deposition time on the microstructural evolution and optical properties of ZnO nanorods were investigated. With increasing deposition time from 1 h to 20 h, the diameter and length of the ZnO nanorods increased gradually to about 328 nm and 6.55${\mu}m$, respectively. The ZnO nanorods were dense and vertically well-aligned. The photoluminescence (PL) peaks corresponding to the near band edge of ZnO were observed. With increasing deposition time, the intensity of PL peaks increased with nanorod growth up to 4 h and then decreased. This might be due to the degradation of crystal quality caused by merging of nanorods.

• 한국표면공학회지
• /
• 제53권6호
• /
• pp.312-321
• /
• 2020

Morphology of porous cobalt electro-deposits was systematically investigated as functions of cobalt precursors in the plating bath and applied cathodic current density with a special focus on cobalt nano-rod formation. It was proved that the concentration of cobalt precursor plays little effect on the morphology of cobalt electro-deposits at relatively low plating current density while it significantly affects the morphology with increasing plating current density. Such a dependence was discussed in terms of the kinetics of two competitive reactions of cobalt reduction and hydrogen evolution. Cobalt nano-rod structure was created at specific ranges of cobalt precursor content and applied cathodic current density, and its diameter and length varied with plating time without notable formation of side branches which is usually found during dendrite formation. Specifically, the nano-rod length was preferentially increased in relative short plating time (<15 s), resulting in higher aspect ratio of nano-rod with plating time. Whereas, both the nano-rod length and diameter were increased nearly at the same level in a prolonged plating time, making the aspect ratio unchanged. From the analysis of crystal structure, it was confirmed that the cobalt nano-rod preferentially grew in the form of single crystal on a dense poly-crystalline cobalt thin film initially formed on the substrate.

• 한국초전도ㆍ저온공학회논문지
• /
• 제11권4호
• /
• pp.16-19
• /
• 2009

The influence of nanorods grown on substrate prior to YBCO deposition has been investigated. We studied the microstructures and characteristic of $YBa_2Cu_3O_{7-\delta}$ films fabricated on $SrTiO_3$ (100) substrates with ZnO nanorods as one of the possible pinning centers. The growth density of ZnO nanorods was modulated through Au nanoparticles synthesized on top of the STO(100) substrates with self assembled monolayer. The density of Au nanoparticles is approximately $240{\sim}260\;{\mu}m^{-2}$ with diameters of 41~49 nm. ZnO nanorods were grown on Au nanoparticles by hot-walled PLD with Au nanoparticles. Typical size of ZnO nanorod was around 179 nm in diameter and $2{\sim}6\;{\mu}m$ in length respectively. The ZnO nanorods have apparently randomly aligned and exhibit single-crystal nature along (0002) growth direction. Our preliminary results indicate that YBCO film deposited directly on STO substrate shows the c-axis orientation while YBCO films with ZnO nanorods exhibit any mixed phases without any typical crystal orientation.

• 한국재료학회지
• /
• 제24권10호
• /
• pp.543-549
• /
• 2014

A zinc oxide (ZnO) hybrid structure was successfully fabricated on a glass substrate by metal organic chemical vapor deposition (MOCVD). In-situ growth of a multi-dimensional ZnO hybrid structure was achieved by adjusting the growth temperature to determine the morphologies of either film or nanorods without any catalysts such as Au, Cu, Co, or Sn. The ZnO hybrid structure was composed of one-dimensional (1D) nanorods grown continuously on the two-dimensional (2D) ZnO film. The ZnO film of 2D mode was grown at a relatively low temperature, whereas the ZnO nanorods of 1D mode were grown at a higher temperature. The change of the morphologies of these materials led to improvements of the electrical and optical properties. The ZnO hybrid structure was characterized using various analytical tools. Scanning electron microscopy (SEM) was used to determine the surface morphology of the nanorods, which had grown well on the thin film. The structural characteristics of the polycrystalline ZnO hybrid grown on amorphous glass substrate were investigated by X-ray diffraction (XRD). Hall-effect measurement and a four-point probe were used to characterize the electrical properties. The hybrid structure was shown to be very effective at improving the electrical and the optical properties, decreasing the sheet resistance and the reflectance, and increasing the transmittance via refractive index (RI) engineering. The ZnO hybrid structure grown by MOCVD is very promising for opto-electronic devices as Photoconductive UV Detectors, anti-reflection coatings (ARC), and transparent conductive oxides (TCO).

• 전기화학회지
• /
• 제14권4호
• /
• pp.196-200
• /
• 2011

본 연구에서는 니오븀 산화물을 비교적 저온에서 단시간 동안의 양극산화법을 통해 제조하였다. 이때, 전해질로는 NaF와 HF를 혼합하여 사용하였으며, 20~120 V의 다양한 전압 조건에 따라 생성되는 니오븀 산화물의 미세구조를 관찰하였다. 일반적으로 니오븀 금속의 양극산화 시 초기에 생성된 니오븀 산화물은 무정형 구조이나 반응이 경과함에 따라 점차 결정형 산화물로 성장하게 된다. 이러한 산화물은 XRD 분석을 통하여 결정형의 $Nb_2O_5$ 임을 확인하였고, FE-SEM 분석결과, 그 표면은 매우 밀집된 형태의 나노로드로 이루어진 마이크로콘 산화물임을 알 수 있었다. 적절한 공정변수로 제조된 니오븀 산화물은 마이크로콘 구조 전체 표면에 걸쳐 동일한 크기를 갖는 나노로드 다발을 형성하고 있으며, 이러한 나노 구조는 또한 넓은 표면적을 기대할 수 있어 염료감응 태양전지나 바이오 소재 등에 대한 다양한 분야에 응용될 수 있을 것으로 기대된다.

• 대한화학회지
• /
• 제60권2호
• /
• pp.131-136
• /
• 2016

CdSe 기반 나노결정의 구리이온에 의한 형광 소광 특성 및 아연이온에 의한 형광 회복 특성을 관찰하였다. 구리이온이 첨가되었을 경우, CdSe 양자점에서는 매우 빠르고 급격한 형광 소광 특성을 보이는 반면에 CdSe 나노라드의 경우에서는 형광이 서서히 소광되는 특성을 보인다. 구리이온으로 형광을 소광시킨 CdSe/CdS(핵/껍질) 양자점에 아연이온이 첨가되면 소광된 양자점의 형광이 회복된다. 용액 내 1 μM의 아연농도에서 양자점의 형광이 50% 증가됨을 확인하였으며, 아연 농도가 증가함에 따라 양자점의 형광세기가 증가되며 이는 Langmuir binding isotherm 모델로 해석할 수 있다. 이러한 연구를 바탕으로 CdSe 기반의 나노결정을 이용한 형광 화학 센서를 구현할 수 있을 것으로 기대한다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2015년도 제49회 하계 정기학술대회 초록집
• /
• pp.76.1-76.1
• /
• 2015

Optical resonances of metallic or dielectric nanoantennas enable to effectively convert free-propagating electromagnetic waves to localized electromagnetic fields and vice versa. Plasmonic resonances of metal nanoantennas extremely modify the local density of optical states beyond the optical diffraction limit and thus facilitate highly-efficient light-emitting, nonlinear signal conversion, photovoltaics, and optical trapping. The leaky-mode resonances, or termed Mie resonances, allow dielectric nanoantennas to have a compact size even less than the wavelength scale. The dielectric nanoantennas exhibiting low optical losses and supporting both electric and magnetic resonances provide an alternative to their metallic counterparts. To extend the utility of metal and dielectric nanoantennas in further applications, e.g. metasurfaces and metamaterials, it is required to understand and engineer their scattering characteristics. At first, we characterize resonant plasmonic antenna radiations of a single-crystalline Ag nanowire over a wide spectral range from visible to near infrared regions. Dark-field optical microscope and direct far-field scanning measurements successfully identify the FP resonances and mode matching conditions of the antenna radiation, and reveal the mutual relation between the SPP dispersion and the far-field antenna radiation. Secondly, we perform a systematical study on resonant scattering properties of high-refractive-index dielectric nanoantennas. In this research, we examined Si nanoblock and electron-beam induced deposition (EBID) carbonaceous nanorod structures. Scattering spectra of the transverse-electric (TE) and transverse-magnetic (TM) leaky-mode resonances are measured by dark-field microscope spectroscopy. The leaky-mode resonances result a large scattering cross section approaching the theoretical single-channel scattering limit, and their wide tuning ranges enable vivid structural color generation over the full visible spectrum range from blue to green, yellow, and red. In particular, the lowest-order TM01 mode overcomes the diffraction limit. The finite-difference time-domain method and modal dispersion model successfully reproduce the experimental results.

• 한국재료학회지
• /
• 제19권11호
• /
• pp.596-600
• /
• 2009

Electrochemical deposition characteristics of CdSe nanorods were investigated for hybrid solar cell applications. CdSe nanorods were fabricated by electrochemical method in $CdSO_4$ and $H_2SeO_3$ dissolved aqueous solution using an anodic aluminum oxide (AAO) template. Uniformity of CdSe nanorods was dependent on the diameter and the height of holes in AAO. The current density, current mode, bath composition and temperature were controlled to obtain a 1:1 atomic composition of CdSe. CdSe nanorods deposited by direct-current method showed better uniformity compared to those deposited by purse-current and/or purse-reverse current methods due to the bottom-up filling characteristics. $H_2SeO_3$ concentration showed more significant effects on pH of solution and stoichiometry of deposits compared to that of $CdSO_4$. A 1:1 stoichiometry of uniform CdSe nanorods was obtained from 0.25M $CdSO_4-5$ mM $H_2SeO_3$ electrolytes with a direct current of 10 $mA/cm^2$ at room temperature. X-ray diffraction and electron diffraction pattern investigations demonstrate that CdSe nanorods are a uniform cubic CdSe crystal.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제44회 동계 정기학술대회 초록집
• /
• pp.226-226
• /
• 2013

Si is a dominant solar material, which is the second most abundant element in the earth giving a benefit in the aspect in cost with low toxicity. However, the inherent limit of Si has an indirect band gap of 1.1 eV resulting in the limited optical absorption. Therefore, a critical issue has been raised to increase the utilization of the incident light into the Si absorber. The enhancement of light absorption is a crucial to improve the performances and thus relieves the cost burden of Si photovoltaics. For the optical aspect, an efficient design of a front surface, where the incident light comes in, has been intensively investigated to improve the performance of photon absorption. Lambertian light trapping can be attained when the light active surface is ideally rough to increase the optical length by about 50 compared to a planar substrate. This suggests that an efficient design may reduce thickness of the Si absorber from the conventional 100~300 ${\mu}m$ to less than 3 ${\mu}m$. Theoretically, a hole-array structure satisfies an equivalent efficiency of c-Si with only one-twelfth mass and one-sixth thickness. Various approaches have been applied to improve the incident light utilization in a Si absorber using textured structures, periodic gratings, photonic crystals, and nanorod arrays. We have designed hole and pillar structured Si absorbers. Four-different Si absorbers have been simultaneously fabricated on an identical Si wafer with hole arrays or pillar arrays at a fixed depth of 2 ${\mu}m$. We have found that the significant enhanced solar cell performances both for the hole arrayed and pillar arrayed Si absorbers compared to that of a planar Si wafer resulting from the effective improvement in the quantum efficiencies.

• 한국분말재료학회지
• /
• 제23권5호
• /
• pp.343-347
• /
• 2016

Fe-based pigments have attracted much interest owing to their eco-friendliness. In particular, the color of nanosized pigments can be tuned by controlling their size and morphology. This study reports on the effect of length on the coloration of ${\beta}$-FeOOH pigments prepared using an $NH_4OH$ solution. First, rod-type ${\beta}$-FeOOH is prepared by the hydrolysis of $FeCl_3{\cdot}6H_2O$ and $NH_4OH$. When the amount of $NH_4OH$ is increased, the length of the rods decreases. Thus, the length of the nanorods can be adjusted from 10 nm to 300 nm. The color of ${\beta}$-FeOOH changes from orangered to yellow depending on the length of ${\beta}$-FeOOH. The color and phase structure of ${\beta}$-FeOOH is characterized by UV-vis spectroscopy, CIE Lab color parameter measurements, transmission electron microscopy (TEM), scanning electron microscopy (SEM), and powder X-ray diffraction (XRD).