• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.204.1-204.1
• /
• 2013

Fluorine, the radius of which is close to that of oxygen, could be an appropriate anion doping candidate. A lower lattice distortion could be expected for F doping, compared with Al, Ga, and In doping. F-doped ZnO (FZO) and undoped ZnO nanorods were grown onto glass substrate by the hydrothemal method. The doping level in the solution, designated by F/Zn atomic ratio of was varied from 0.0 to 10.0 in 2.0 steps. To investigate the effects of the structure and optical properties of FZO nanorods were investigated using X-ray diffraction, UV-visible spectroscopy and photoluminescence (PL). For the PL spectra, the maximum peak position of NBE moves to higher energy, from 0 to 4 at.%. As the doping concentration increases, the maximum peak position of NBE gradually moves to lover energy, from 4 to 10 at.%.

• Journal of the Korean Ceramic Society
• /
• v.42 no.6 s.277
• /
• pp.377-383
• /
• 2005

Generally, the strength achieved of glass-ceramics is higher as is the fracture toughness, as compared with the original glass. This improvement is due to the microstructure consisting of very small crystals. In this study, Ag-doped $45SiO_2-24CaO-24Na_2O-4P_2O_5$ glasses were irradiated to strengthen by the crystallization using Femto second laser Pulses. Through the UV/VIS spectroscope, XRD, Nano-indenter and SEM etc., heat-treated and irradiation of laser pulses without heat-treated samples were analyzed. Two kinds of samples, heat-treated and laser irradiated without heat-treated samples, showed the peaks in the same wavelength near 360 nm. Especially, samples irradiated by 140 mW laser with XYZ stage having at the rate of 100$\~$l000 $\mu$m/s had the largest absorption peak among them, and heat-treated samples was shown lower absorption range than over 90 mW laser irradiated samples. Moreover, samples irradiated by laser had higher values ($4.4\~4.56{\times}10^{-3}(Pa)$) of elastic modulus which related with strength of glass than values of heat-treated samples and these are 1.2$\~$1 .5 times higher values than them of mother glass.

• Journal of Powder Materials
• /
• v.25 no.5
• /
• pp.426-434
• /
• 2018

In this study, $MgO-CaO-Al_2O_3-SiO_2$ (MCAS) nanocomposite glass powder having a mean particle size of 50 nm and a specific surface area of $40m^2/g$ is used as a sintering additive for AlN ceramics. Densification behaviors and thermal properties of AlN with 5 wt% MCAS nano-glass additive are investigated. Dilatometric analysis and isothermal sintering of AlN-5wt% MCAS compact demonstrates that the shrinkage of the AlN specimen increases significantly above $1,300^{\circ}C$ via liquid phase sintering of MCAS additive, and complete densification could be achieved after sintering at $1,600^{\circ}C$, which is a reduction in sintering temperature by $200^{\circ}C$ compared to conventional $AlN-Y_2O_3$ systems. The MCAS glass phase is satisfactorily distributed between AlN particles after sintering at $1,600^{\circ}C$, existing as an amorphous secondary phase. The AlN specimen attained a thermal conductivity of $82.6W/m{\cdot}K$ at $1,600^{\circ}C$.

• Korean Journal of Metals and Materials
• /
• v.49 no.4
• /
• pp.313-320
• /
• 2011

100 nm-thick hydrogenated amorphous silicon $({\alpha}-Si:H)$ films were deposited on a glass and glass/30 nm Ni substrates by inductively-coupled plasma chemical vapor deposition (ICP-CVD) at temperatures ranging from 100 to $550^{\circ}C$. The sheet resistance, microstructure, phase transformation and surface roughness of the films were characterized using a four-point probe, AFM (atomic force microscope), TEM (transmission electron microscope), AES (Auger electron spectroscopy), HR-XRD(high resolution X-ray diffraction), and micro-Raman spectroscopy. A nano-thick NiSi phase was formed at substrate temperatures >$400^{\circ}C$. AFM confirmed that the surface roughness did not change as the substrate temperature increased, but it increased abruptly to 6.6 nm above $400^{\circ}C$ on the glass/30 nm Ni substrates. HR-XRD and micro-Raman spectroscopy showed that all the Si samples were amorphous on the glass substrates, whereas crystalline silicon appeared at $550^{\circ}C$ on the glass/30 nm Ni substrates. These results show that crystalline NiSi and Si can be prepared simultaneously on Ni-inserted substrates.

• Korean Journal of Optics and Photonics
• /
• v.18 no.6
• /
• pp.441-446
• /
• 2007

Outcoupling efficiency of the OLED device is improved by incorporating both a microlens array and a diffractive grating pattern. The microlens array improves the light transmission at the interface of glass and air, and the diffractive grating outcouples the guided mode propagating at the waveguide, which consists of ITO and organic layers. By using the PDMS soft mold imprinting method, the microlens array is fabricated on the glass substrate. The diffractive grating pattern is directly fabricated on the ITO surface by using laser interferometry. A microlens array with a diameter of $10{\mu}m$ improves the light coupling efficiency by 22%. The diffractive grating made of TSMR photoresist enhances the luminance power efficiency by 41% at a current density of $20mA/cm^2$.

• Korean Journal of Materials Research
• /
• v.27 no.2
• /
• pp.94-99
• /
• 2017

Dinickel-silicide $(Ni_2Si)/glass$ was employed as a counter electrode for a dye-sensitized solar cell (DSSC) device. $Ni_2Si$ was formed by rapid thermal annealing (RTA) at $700^{\circ}C$ for 15 seconds of a 50 nm-Ni/50 nm-Si/glass structure. For comparison, $Ni_2Si$ on quartz was also prepared through conventional electric furnace annealing (CEA) at $800^{\circ}C$ for 30 minutes. XRD, XPS, and EDS line scanning of TEM were used to confirm the formation of $Ni_2Si$. TEM and CV were employed to confirm the microstructure and catalytic activity. Photovoltaic properties were examined using a solar simulator and potentiostat. XRD, XPS, and EDS line scanning results showed that both CEA and RTA successfully led to tne formation of nano $thick-Ni_2Si$ phase. The catalytic activity of $CEA-Ni_2Si$ and $RTA-Ni_2Si$ with respect to Pt were 68 % and 56 %. Energy conversion efficiencies (ECEs) of DSSCs with $CEA-Ni_2Si$ and $RTA-Ni_2Si$catalysts were 3.66 % and 3.16 %, respectively. Our results imply that nano-thick $Ni_2Si$ may be used to replace Pt as a reduction catalytic layer for a DSSCs. Moreover, we show that nano-thick $Ni_2Si$ can be made available on a low-cost glass substrate via the RTA process.

• Journal of the Korean Ceramic Society
• /
• v.44 no.6 s.301
• /
• pp.297-302
• /
• 2007

With aids of square wave voltammetry (SWV) the redox behavior for various combination of polyvalent ions (Sb+Fe, Sb+Zn, Sb+Ce+Ti+Zn) was investigated in alkali-alkaline earth-silica CRT (Cathode Ray Tube) glass melts. The current-potential curve so called voltammogram was produced at temperature range of 1400 to $1000^{\circ}C$ under the scanned potential between 0 and -800 mV at 100 Hz. In the case of the Sb+Fe and Sb+Zn doped melts, peak for $Sb^{3+}/Sb^0$ shown voltammogram was shifted to negative direction comparing to the only Sb doped melts. However, according to voltammogram of Sb+Ce+Ti+Zn doped melt, Ti and Ce except Zn had hardly any influence on the redox reaction of Sb. Based on the temperature dependence of the peak potential, standard enthalpy (${\Delta}H^0$) and standard entropy (${\Delta}S^0$) for the reduction of $Fe^{3+}$ to $Fe^{2+}$, $Sb^{3+}$ to $Sb^0$, $Zn^{2+}$ to $Zn^0$ and $Ti^{2+}$ to $Ti^0$ in each polyvalent ion combination of CRT glass melts were calculated.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.10a
• /
• pp.171-174
• /
• 2005

To improve the strength of glass is being studied in order to contribute to weight saving of flat panel displays. Generally, the strength achieved of glass-ceramics is higher as is the fracture toughness by the formation of a heterogeneous Phase inside glass. In this study, Ag-doped $45SiO_2-24CaO-24Na_2O-4P_2O_5$ glasses were irradiated to strengthen by crystallization using femto-second laser pulse. UV/VIS, Spectroscope, XRD, nano-indenter and SEM etc. irradiation of laser pulse without heat-treated samples was analyzed. Samples irradiated by laser had higher value$(4.4\~4.56{\ast}10-3Pa)$ of elastic modulus which related with strength of glass than values heat-treated samples and these are $1.2\~1.5$ times higher values than them of mother glass. This process can be applicable to the strengthening of thinner glass plate, and it has an advantage over traditional heat-treatment and ion-exchange method.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.2
• /
• pp.210-217
• /
• 2004

In this study, a new process, named as nano replication printing(nRP) process, is developed for printing any figure in the range of several micrometers by using voxel matrix scanning scheme. In this newly developed process, a femto-second laser is scanned on a photosensitive monomer resin in order to induce polymerization of the liquid resin according to a voxel matrix which is transformed from bitmap format file. After the polymerization, a droplet of ethanol is dropt to remove the unnecessary remaining liquid resin and then the polymerized figures with nano-scaled precision are only remaining on the glass plate. By the nRP process, any figure file of bitmap format could be reproduced as nano-scaled precision replication in the range of several micrometers. Also, nano/micro-scaled patterns for an extremely wide range of applications would become a technologically feasible reality. Some of figures with nano-scaled precision were printed in scaled replication as examples to prove the usefulness of this study.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.545-545
• /
• 2007

Recently, innovative process has been investigated in order to replace the conventional high-cost micro patterning processes on the electronic products. To produce desirable profit margins from this low cost products, printed circuit board(PCB), will require dramatic changes in the current manufacturing philosophies and processes. Innovative process using metal nano particles replaces the current industry standard of subtractive etched of copper as a highly efficient way to produce robust circuitry on low cost substrates. An advantage of using metal nano particles process in patterned conductive line manufacturing is that the process is additive. Material is only deposited in desired locations, thereby reducing the amount of chemical and material waste. Simply, it just draws on the substrate as glass epoxy or polyimide with metal nano particles. Particles, when their size becomes nano-meter scale, show some specific characteristics such as enhanced reactivity of surface atoms, decrease in melting point, high electric conductivity compared with the bulk. Melting temperature of metal gets low, the metal nano particles could be formated onto polymer substrates and sintered under $300^{\circ}C$, which would be applied in PCB. It can be getting the metal line of excellent electric conductivity.