• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.12
• /
• pp.1091-1098
• /
• 1998

Thermal stability of the electroless deposited Cu thin film was investigated. Cu/TaN/Si multilayer was fabricated by electroless-depositing Cu thin layer on TaN diffusion barrier layer which was deposited by MOCVD on the Si substrate, and was annealed in $H_2$ ambient to investigate the microstructure of Cu film with a post heat-treatment. Cu thin film with good adhesion was successfully deposited on the surface of the TaN film by electroless deposition with a proper activation treatment and solution control. Microstructural property of the electroless-deposited Cu layer was improved by a post-annealing in the reduced atmosphere of $H_2$ gas up to $600^{\circ}C$. Thermal stability of Cu/TaN/Si system was maintained up to $600^{\circ}C$ annealing temperature, but the intermediate compounds of Cu-Si were formed above $650^{\circ}C$ because Cu element passed through the TaN layer. On the other hand, thermal stability of the Cu/TaN/Si system in Ar ambient was maintained below $550^{\circ}C$ annealing temperature due to the minimal impurity of $O_2$ in Ar gas.

• Journal of the Korean institute of surface engineering
• /
• v.29 no.5
• /
• pp.325-329
• /
• 1996

We report on p-type arsenic doping of metalorganic vapor phase epitaxially (MOVPE) grown HgCdTe on (100) GaAs. HgCdTe was grown at $370^{\circ}C$ in a horizontal reactor with using dimethy-cadmium, diisoprophyltelluride, and elemental Hg. We used tris-dimethylaminoarsenic (DMAAs) as the metalorganic for p-doping. 4micron thick CdTe and subsequently 10micron thick HgCdTe were grown on (100) GaAs substrate. Interdiffused multilayer process in which thin CdTe and HgTe layers are grown alternately and interdiffused to obtain homogeneous HgCdTe alloys was used. Arsenic was doped during CdTe growth cycle. After growth HgCdTe was annealed at $415^{\circ}C$ for 15 min and then annealed again at $220^{\circ}C$ for 3 hr, both with Hg-saturate condition. We could obtain p-doping from 2.5$\times$$10^{16}$ to 6.6$\times$$10^{17}$$cm^{-3}$, depending on the DMAAs partial pressure. With the dual Hg-annealing, activation of arsenic was aboutt 90%, which was confirmed by SIMS measurement. With only low temperature annealing at $220^{\circ}C$ for 3hr, activation efficiency was about 50%.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.31 no.6
• /
• pp.408-411
• /
• 2018

We fabricated highly flexible Mn-doped $SnO_2$ (MTO)/Ag/MTO/polydimethylsiloxane (PDMS)/MTO multilayer transparent conducting films. To reduce refractive-index mismatching of the MTO/Ag/MTO/polyethylene terephthalate (PET), index-matching layers were inserted between the oxide-metal-oxide-structured films and the PET substrate. The PDMS layer was deposited by spin-coating after adjusting the mixing ratio of PDMS and hexane. We investigated the effects of the index-matching layer on the color and reflectance differences with different PDMS dilution ratios. As the dilution ratio increased from 1:100 to 1:130, the color difference increased slightly, while the reflectance difference decreased from 0.62 to 0.32. The MTO/Ag/MTO/PDMS/MTO film showed a transmittance of 87.18~87.68% at 550 nm. The highest value of the Haacke figure of merit was $47.54{\times}10^{-3}{\Omega}^{-1}$ for the dilution ratio of 1:130.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2007.04a
• /
• pp.147-148
• /
• 2007

In this study, the technology to grow oriented nanotube thin film from dip-coated $TiO_2$ using hydrothermal method has been successfully developed. The effects of preparation parameters, such as reaction temperature, duration and post treatment conditions on the film morphologies and the adherence to the substrate, have been examined. A general formation mechanism of oriented titanate nanotube thin film is proposed in terms of the detailed observation of the products via two dimensional surface FESEM studies and HRTEM images. The overall formation of $TiO_2-based$ nanotube thin film can be summarized with three successive steps: (1) $TiO_2$ dissolving and amorphous $Na_2TiO_3$ deposition process; (2) layered $Na_2Ti_3O_7$ formation via spontaneous crystallization and rapid growth process; (3) formation of nanotube thin film via $Na_2Ti_3O_7$ splitting and multilayer scrolling process of (100) planes around the c axis of $Na_2Ti_3O_7$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.11a
• /
• pp.468-471
• /
• 2004

Monolayers of lipids on a water surface have attracted much interest as models of biological membranes, but also as precursors of multilayer systems premising many technical applications. Until now, many methodologies have been developed in order to gain a better understand. Photoisomerization in monolayers of a novel azobenzene compound, azobenzene dendrimer, was investigated for the first time by means of the absorption spectrum and Maxwell displacement current (MDC) technique. Dendrimers are well-defined macromolecules exhibiting a tree-like structure, first derived by the cascade molecule approach. According to the absorption spectrum, trans-to-cis conversion ratio was estimated to the third generation of azobenzene dendrimer deposited onto a glass substrate. Temperature-dependent induced charge with trans-cis isomerization was also measured by means of MDC technique.

• Journal of the Korean Physical Society
• /
• v.73 no.9
• /
• pp.1279-1282
• /
• 2018

This paper reports the deposition of a metal line using a multilayer stack and laser-induced forward transfer (LIFT) using a low cost continuous wave blue laser with a wavelength of 450 nm. The donor structure was composed of a light-to-heat (LTH) layer, a release layer, and a transfer layer in series. Amorphous silicon as the LTH layer absorbs photon energy and converts it to heat. A release layer was melted so that a silver transfer layer would be transferred to the receiver substrate. The transferred silver layer showed reasonable physical and electrical characteristics. A low cost fine linewidth metal layer could be achieved using this modified LIFT technique and blue laser.

• Current Optics and Photonics
• /
• v.1 no.1
• /
• pp.7-11
• /
• 2017

In this study, multilayered graphene was easily transferred to the target substrate in one step using thermal release tape. The transmittance of the transferred graphene according to the number of layers was measured using a spectrophotometer. The sheet resistance was measured using a four-point probe system. Graphene formed using this transfer method showed almost the same electrical and optical properties as that formed using the conventional poly (methyl methacrylate) transfer method. This method is suitable for the mass production of graphene because of the short process time and easy large-area transfer. In addition, multilayered graphene can be transferred on various substrates without wetting problem using the one-step dry transfer method. In this work, this easy transfer method was used for dielectric substrates such as glass, paper and polyethylene terephthalate, and a sheet resistance of ~240 ohm/sq was obtained with three-layer graphene. By fabricating organic solar cells, we verified the feasibility of using this method for optoelectronic devices.

• Journal of the Korean Magnetics Society
• /
• v.9 no.1
• /
• pp.41-47
• /
• 1999

$Buffer/[NiFe/Cu/CoFe(Co)/Cu]_N$ spin valve multilayers prepared by dc magnetron sputtering on a corning glass substrate using NiFe and CoFe(Co) posses different coercivities. Dependence of magnetoresistance on the type and thickness of buffer layer, thickness of Cu, NiFe, stacking number of multilayer, substrate temperature and annealing temperature in the form $[NiFe/Cu/CoFe(Co)/Cu]_N$ spin-valve multilayers were investigated. To evaluate effect of magnetoresistance for this samples, X-ray diffraction analysis, vibrating sample magnetometer analysis, and magnetoresistance measurement (4-probe method) were performed the maximum magnetoresistance ratio and coercivity were 7.5 % and 140 Oe, respectively for $Cr-50{\AA}/[NiFe-20{\AA}/Cu-{\AA}/Co-20{\AA}/Cu-50{\AA}]_10$ at substrate temperature of 9$0^{\circ}C$. Magnetoresistance slope maintained 0.25%/Oe until 15$0^{\circ}C$ of annealing temperature, and then decreased to 0.03%/Oe at 20$0^{\circ}C$. It was confirmed that the main factor of thermal stability was deteriorating of soft magnetic properties in the NiFe layer.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.1
• /
• pp.73-80
• /
• 2004

In this paper, the implementation and embedding method of the existing air-filled waveguide-filters at millimeter-wave on general PCB substrate is introduced by systematically inserting the vias inside waveguide and mathematically manipulating the simple equations obtained ken the classical circular-post waveguide filter design. All the metal structures placed vertically such as side wall fur perfect ground plane and circular-post for signal control in the air-filled WR-22 waveguide are replaced with several types of via for constructing the bandpass-filter. Side wall and poles inside waveguide are realized by placing a series array of via and tuning the via diameter. The lengths of x, y, z axis are reduced in proportion to root square of employed substrate dielectric constant and especially the length of z axis can be more reduced due to the characteristics of the wave propagation. Because the mass production on PCB is possible without fabricating a large-scaled metal waveguide of WR-22 as input/output ports at millimeter-wave regime, the manufacturing cost is reduced considerably. Finally, when using multilayer process like LTCC for small-sized module, it is one of advantages to use only one layer f3r the filter fabrication. To evaluate the validity of this novel technique, order-3 Chebyshev BPF(Bandpass-Filter) centered at 40 GHz-band with a 2.5 ％ FBW (Fractional Bandwidth) were used. The employed substrate has relative dielectric constant of 2.2 and thickness of 10 mil of Rogers RT/Duroid 5880. Accroding to design and measurement results, a good performance of insertion loss of 2 ㏈ and return loss of -30 ㏈ is achieved at full input/output ports.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.4 no.4
• /
• pp.378-387
• /
• 1994

To improve the properties of $PbTiO_3$ thin films successfully grown by thermal diffusion of 3 component layers of $Ti0_2/Pb/TiO_2(900{\AA}/900{\AA}/900{\AA})$ in preceding research, 3, 5, 7, 9, and 11 multilayer structures $(TiO_2/Pb/.../Tio_2)$ with thinner component layer of $200~300 {\AA}$ thick were deposited on Si substrate by RF sputtering, which were followed by RTA to form $PbTiO_3$ thin films. As a result, $PbTiO_3$ single phase was formed above $500^{\circ}C$. When the thickness of component layer reduced and the number of component layers increased, suppression of Pb-silicate and voids formation resulted in relatively sharp interfaces and the film composition became more homogeneous. Relative dielectric constants in MIM structure were independent of the annealing condition, but they increased with increasing thickness of the $PbTiO_3$ thin films. The maximum breakdown field in MIS structure reached 150kV/cm.