• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.7
• /
• pp.39-46
• /
• 2016

This paper describes the third order feedforward delta-sigma modulator with inverter-based integrators and a 1.5bit comparator for the application of audio signal processing. The proposed 3rd-order delta-sigma modulator is multi-bit structure using 1.5 bit comparator instead of operational amplifier. This delta-sigma modulator has high SNR compared with single-bit 4th-order delta-sigma modulator in a low OSR. And it minimizes power consumes and simplified circuit structure using inverter-based integrator and using inverter-based integrator as analogue adder. The modulator was designed with 0.18um CMOS standard process and total chip area is $0.36mm^2$. The measured power cosumption is 28.8uW in a 0.8V analog supply and 66.6uW in a 1.8V digital supply. The measurement result shows that the peak SNDR of 80.7 dB, the ENOB of 13.1bit and the dynamic range of 86.1 dB with an input signal frequency of 2.5kHz, a sampling frequency of 2.56MHz and an oversampling rate of 64. The FOM (Walden) from the measurement result is 269 fJ/step, FOM (Schreier) was calculated as 169.3 dB.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.9
• /
• pp.7-13
• /
• 2009

This paper presents a multi-channel transceiver that achieves a data rate of 3.125Gb/s/ch. The LVDS is used because of its noise immunity and low power consumption. And a pre-emphasis circuit is also proposed to increase the transmitter speed. On the receiver side, a low-power CDR(clock and data recovery) using 1/4-rate clock based on dual-interpolator is proposed. The CDR generates needed additional clocks in each recovery part internally using only inverters. Therefore each part can be supplied with the same number of 1/4-rate clocks from a clock generator as in 1/2-rate clock method. Thus, the reduction of a clock frequency relaxes the speed limitation and lowers power dissipation. The prototype chip is comprised of two channels and was fabricated in a $0.18{\mu}m$ standard CMOS process. The output jitter of transmitter is loops, peak-to-peak(0.31UI) and the measured recovered clock jitter is 47.33ps, peak-to-peak which is equivalent to 3.7% of a clock period. The area of the chip is $3.5mm^2$ and the power consumption is about 119mW/ch.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.19 no.2
• /
• pp.102-105
• /
• 2009

The accelerated life time test of the MLCCs with different $BaTiO_3$ particle sizes were conducted at $150^{\circ}C$, 75 V condition and the effect of $BaTiO_3$ particle size on the breakdown voltage and degradation characteristics of MLCCs was investigated. The MLCCs were prepared by using the $BaTiO_3$ particles having the size of $0.525{\mu}m$, $0.555{\mu}m$, $0.580{\mu}m$ and Ni-electrode, respectively. The MLCCs which have the particle size of $0.525{\mu}m$, $0.555{\mu}m$, and $0.580{\mu}m$, respectively were confirmed to meet the standard requirements of X5R(change capacitance within ${\pm}15%$ at $-55{\sim}85^{\circ}C$) by TCC(Temperature Coefficient of Capacitance). The effect of the $BaTiO_3$ particle size on the insulation resistance behavior of MLCCs was confirmed by BDV(Breakdown Voltage) measurements and the cause and degree of degradation of MLCCs were characterized by XPS analysis after the accelerated life test. The MLCCs with $0.525{\mu}m-BaTiO_3$ showed better insulation resistance and BDV characteristics compare to other MLCCs and XPS analysis revealed that the MLCCs degradation is caused by the NiO peak and $BaTiO_3$ peak decrease.

• Imaging Science in Dentistry
• /
• v.50 no.1
• /
• pp.1-7
• /
• 2020

Purpose: This study was performed to evaluate the magnitude of artifacts produced by gutta-percha and metal posts on cone-beam computed tomography (CBCT) scans obtained with different tube currents and with or without metal artifact reduction (MAR). Materials and Methods: A tooth was inserted in a dry human mandible socket, and CBCT scans were acquired after root canal instrumentation, root canal filling, and metal post placement with various tube currents with and without MAR activation. The artifact magnitude was assessed by the standard deviation (SD) of gray values and the contrast-to-noise ratio (CNR) at the various distances from the tooth. Data were compared using multi-way analysis of variance. Results: At all distances, a current of 4 mA was associated with a higher SD and a lower CNR than 8 mA or 10 mA (P<0.05). For the metal posts without MAR, the artifact magnitude as assessed by SD was greatest at 1.5 cm or less (P<0.05). When MAR was applied, SD values for distances 1.5 cm or closer to the tooth were reduced (P<0.05). MAR usage did not influence the magnitude of artifacts in the control and gutta-percha groups(P>0.05). Conclusion: Increasing the tube current from 4 mA to 8 mA may reduce the magnitude of artifacts from metal posts. The magnitude of artifacts arising from metal posts was significantly higher at distances of 1.5 cm or less than at greater distances. MAR usage improved image quality near the metal post, but had no significant influence farther than 1.5 cm from the tooth.

• Asian-Australasian Journal of Animal Sciences
• /
• v.29 no.8
• /
• pp.1083-1094
• /
• 2016

Carcass and price traits of 72,969 Hanwoo cows, bulls and steers aged 16 to 80 months at slaughter collected from 2002 to 2013 at 75 beef packing plants in Korea were analyzed to determine heritability, correlation and breeding value using the Multi-Trait restricted maximum likelihood (REML) animal model procedure. The traits included carcass measurements, scores and grades at 24 h postmortem and bid prices at auction. Relatively high heritability was found for maturity ($0.41{\pm}0.031$), while moderate heritability estimates were obtained for backfat thickness ($0.20{\pm}0.018$), longissimus muscle (LM) area ($0.23{\pm}0.020$), carcass weight ($0.28{\pm}0.019$), yield index ($0.20{\pm}0.018$), yield grade ($0.16{\pm}0.017$), marbling ($0.28{\pm}0.021$), texture ($0.14{\pm}0.016$), quality grade ($0.26{\pm}0.016$) and price/kg ($0.24{\pm}0.025$). Relatively low heritability estimates were observed for meat color ($0.06{\pm}0.013$) and fat color ($0.06{\pm}0.012$). Heritability estimates for most traits were lower than those in the literature. Genetic correlations of carcass measurements with characteristic scores or quality grade of carcass ranged from -0.27 to +0.21. Genetic correlations of yield grade with backfat thickness, LM area and carcass weight were 0.91, -0.43, and -0.09, respectively. Genetic correlations of quality grade with scores of marbling, meat color, fat color and texture were -0.99, 0.48, 0.47, and 0.98, respectively. Genetic correlations of price/kg with LM area, carcass weight, marbling, meat color, texture and maturity were 0.57, 0.64, 0.76, -0.41, -0.79, and -0.42, respectively. Genetic correlations of carcass price with LM area, carcass weight, marbling and texture were 0.61, 0.57, 0.64, and -0.73, respectively, with standard errors ranging from ${\pm}0.047$ to ${\pm}0.058$. The mean carcass weight breeding values increased by more than 8 kg, whereas the mean marbling scores decreased by approximately 0.2 from 2000 through 2009. Overall, the results suggest that genetic improvement of productivity and carcass quality could be obtained under the national scale breeding scheme of Korea for Hanwoo and that continuous efforts to improve the breeding scheme should be made to increase genetic progress.

• Korean Journal of Environmental Agriculture
• /
• v.18 no.4
• /
• pp.310-315
• /
• 1999

The feasibility of an absorbent biofilter system was examined for rural wastewater treatment. Hydraulic loading rates varied from 50 to 250 cm/day. Effluent of the septic tank was fed into the absorbent biofilter, and small ventilation fan was provided to supply air at the rate of 250 L/min to aerate the biofilter. The biofilter system demonstrated high removal rates for $BOD_5$ and TSS at the loading rate of 150 cm/day, generally meeting the Korean effluent water quality standard of 20 mg/L applicable to both. The nutrient removal was less satisfactory than the results of $BOD_5$ and TSS, but it was within the expected range of biological treatment processes. Considering the abnormally high influent concentration of nutrients during the experiment, better performance results could have been obtained if ordinary domestic wastewater was used. The system performance was not significantly affected by the hydraulic loading up to 150 cm/day, which is far more than the loading limit of the sand filter systems. Maintenance requirement was minimal, and no problems with noise, odor, flies or sludge arose. Since the biofilter system can be operated at a distance, operation in remote rural area and multi-system connected to one control office might be advantageous to the rural area. Overall, considering the cost-effectiveness, stable performance, and minimum maintenance, the biofilter system was thought to be a competitive alternative to treat wastewater in Korean rural communities.

• Korean Journal of Remote Sensing
• /
• v.36 no.5_4
• /
• pp.1195-1207
• /
• 2020

With the development of GeoWeb technology, 2D/3D spatial information services through the web are also has been used increasingly in the application of disaster management. This paper is suggested to construct a web-based 3D geo-spatial information mapping platform to visualize various spatial information collected at the disaster site in a web environment. This paper is presented a web-based geo-spatial information mapping service plan for the various types of 2D/3D spatial data and large-volume LiDAR point cloud data collected at the disaster accident site using HTML5/WebGL, web development standard technology and open source. Firstly, the collected disaster site survey 2D data is constructed as a spatial DB using GeoServer's WMS service and PostGIS provided an open source and rendered in a web environment. Secondly, in order to efficiently render large-capacity 3D point cloud data in a web environment, a Potree algorithm is applied to simplifies point cloud data into 2D tiles using a multi-resolution octree structure. Lastly, OpenLayers3 based 3D web mapping pilot system is developed for web visualization of 2D/3D spatial information by implementing basic and application functions for controlling and measuring 3D maps with Graphic User Interface (GUI). For the further research, it is expected that various 2D survey data and various spatial image information of a disaster site can be used for scientific investigation and analysis of disaster accidents by overlaying and visualizing them on a built web-based 3D geo-spatial information system.

• The Korean Journal of Applied Statistics
• /
• v.33 no.2
• /
• pp.215-228
• /
• 2020

Under Article 19, Paragraph 1 of the Food Industry Promotion Act, Rural Development Administration renews the Korean foods composition table every five years. Before the publication of the tenth revision of the Korean foods composition table in 2021, this paper suggests methods for collecting representative samples of 182 highly consumed foods in Korea. Food markets are categorized by their distribution channels, which are supermarkets and local markets. Eight samples are collected from each category by applying the National Food and Nutrient Analysis Program (NFNAP)'s stratified multi-stage sampling. The NFNAP was implemented in 1997 as a collaborative food composition research effort between the National Institute of Health (NIH) and the US Department of Agriculture (USDA) to secure reliable estimates for the nutrient content of food and beverages consumed by the US population. Selected supermarkets for selecting representative food samples are Emart Kayang, Homeplus Siheung, Lottemart Dongducheon, Emart Suwon, Lottemart Dunsan, Lottemart Yeosu, Emart Ulsan, and Hanaroclub Ulsan. Selected local markets also are Doksandongusijang in Geumcheon-gu and Pungnapsijang in Songpa-gu, Seoul, Ilsansijang in Ilsanseo-gu, Goyang, Unamsijang in Buk-gu, Gwangju, Beopdongsijang in Daedeok-gu, Daejeon, Bongnaesijang in Yeongdo-gu and Jwadongjaeraesijang in Haeundae-gu, Busan, and Jungangsijang in Jinhae-gu, Changwon.

• Journal of Korea Water Resources Association
• /
• v.45 no.11
• /
• pp.1143-1156
• /
• 2012

One of the important purposes of most water resources systems is to prevent from drought damages. However, there are uncertainties in water supply plans from a reservoir due to factors such as limitation of available data, inaccuracy of surveyed data, unsuitability of analysis method, and climate change. In actual operating process, severe drought exceeding the water supply capability makes the normal water usage difficult. In Korea, however, alternative water source such as a development of new water project is very limited in case of water shortages due to drought. Especially, since there is no standard to evaluate the water supply effect considering severe drought damages, it is difficult to prepare the practical measures. In this study, water shortage events of existing multipurpose reservoirs are analyzed and the method of using low-storage emergency water supply is studied by using Water Shortage Index (WSI). The water shortage events are analyzed and the effect of water shortage decrease is evaluated using the existing inflow data of multi-purpose reservoirs. The results show that Imha, Daechung, Hapchon and Namkang reservoirs are highly vulnerable to the severe drought and required to develop additional emergency water source.

• Proceedings of the Korean Society of Near Infrared Spectroscopy Conference
• /
• 2001.06a
• /
• pp.1523-1523
• /
• 2001

The wine industry requires practical methods for objectively measuring the composition of both red wine grapes on the vine to determine optimal harvest time; and of freshly harvested grapes for efficient allocation to vinery process streams for particular red wine products, and to determine payment of contract grapegrowers. To be practical for industry application these methods must be rapid, inexpensive and accurate. In most cases this restricts the analyses available to measurement of TSS (total soluble solids, predominantly sugars) by refractometry and pH by electropotentiometry. These two parameters, however, do not provide a comprehensive compositional characterization for the purpose of winemaking. The concentration of anthocyanin pigment in red wine grapes is an accepted indicator of potential wine quality and price. However, routine analysis for total anthocyanins is not considered as a practical option by the wider wine industry because of the high cost and slow turnaround time of this multi-step wet chemical laboratory analysis. Recent work by this ${group}^{l,2}$ has established the capability of near infrared (NIR) spectroscopy to provide rapid, accurate and simultaneous measurement of total anthocyanins, TSS and pH in red wine grapes. The analyses may be carried out equally well using either research grade scanning spectrometers or much simpler reduced spectral range portable diode-array based instrumentation. We have recently expanded on this work by collecting thousands of red wine grape samples in Australia. The sample set spans two vintages (1999 and 2000), five distinct geographical winegrowing regions and three main red wine grape varieties used in Australia (Cabernet Sauvignon, Shiraz and Merlot). Homogenized grape samples were scanned in diffuse reflectance mode on a FOSE NIR Systems6500 spectrometer and subject to laboratory analysis by the traditional methods for total anthocyanins, TSS and pH. We report here an analysis of the correlations between the NIR spectra and the laboratory data using standard chemometric algorithms within The Unscrambler software package. In particular, various subsets of the total data set are considered in turn to elucidate the effects of vintage, geographical area and grape variety on the measurement of grape composition by NIR spectroscopy. The relative ability of discrete calibrations to predict within and across these differences is considered. The results are then used to propose an optimal calibration strategy for red wine grape analysis.