• Proceedings of the KSRS Conference
• /
• 1998.09a
• /
• pp.58-63
• /
• 1998

The aim of the present study is to define and tentatively to interpret the distribution of polluted water released from Lake Sihwa into Yellow Sea using Landsat TM. Since the region is an extreme case 2 water, empirical algorithms for chlorophyll-a and suspended sediments have limitations. This work focuses on the use of multi-temporal Landsat TM. We applied PCA to detect evolution of spatial feature of polluted water after release from the lake. The PCA results were compared with in situ data, such as chlorophyll-a, suspended sediments, Secchi disk depth (SDD), surface temperature, radiance reflectance at six bands. The in situ remote sensing reflectance was analysed with PCA. On the basis of these In situ data we found good correlation between first Principal Component and Secchi disk depth ($R^2$=0.7631), although other variables did not result in such a good correlation. The problems in applying PCA techniques to multi-spectral remote sensed data are also discussed.

• Nuclear Engineering and Technology
• /
• v.41 no.10
• /
• pp.1347-1360
• /
• 2009

A multi-dimensional component for the thermal-hydraulic system analysis code, MARS, was developed for a more realistic three-dimensional analysis of nuclear systems. A three-dimensional and two-fluid model for a two-phase flow in Cartesian and cylindrical coordinates was employed. The governing equations and physical constitutive relationships were extended from those of a one-dimensional version. The numerical solution method adopted a semi-implicit and finite-difference method based on a staggered-grid mesh and a donor-cell scheme. The relevant length scale was very coarse compared to commercial computational fluid dynamics tools. Thus a simple Prandtl's mixing length turbulence model was applied to interpret the turbulent induced momentum and energy diffusivity. Non drag interfacial forces were not considered as in the general nuclear system codes. Several conceptual cases with analytic solutions were chosen and analyzed to assess the fundamental terms. RPI air-water and UPTF 7 tests were simulated and compared to the experimental data. The simulation results for the RPI air-water two-phase flow experiment showed good agreement with the measured void fraction. The simulation results for the UPTF downcomer test 7 were compared to the experiment data and the results from other multi-dimensional system codes for the ECC delivery flow.

• The Journal of Advanced Prosthodontics
• /
• v.16 no.2
• /
• pp.67-76
• /
• 2024

PURPOSE. This study aims to assess and predict lifespan of dental prostheses using newly developed Korean Association of Prosthodontics (KAP) criteria through a large-scale, multi-institutional survey. MATERIALS AND METHODS. Survey was conducted including 16 institutions. Cox proportional hazards model and principal component analysis (PCA) were used to find out relevant factors and predict life expectancy. RESULTS. 1,703 fixed and 815 removable prostheses data were collected and evaluated. Statistically significant factors in fixed prosthesis failure were plaque index and material type, with a median survival of 10 to 18 years and 14 to 20 years each. In removable prosthesis, factors were national health insurance coverage, antagonist type, and prosthesis type (complete or partial denture), with median survival of 10 to 13 years, 11 to 14 years, and 10 to 15 years each. For still-usable prostheses, PCA analysis predicted an additional 3 years in fixed and 4.8 years in removable prosthesis. CONCLUSION. Life expectancy of a prosthesis differed significantly by factors mostly controllable either by dentist or a patient. Overall life expectancy was shown to be longer than previous research.

• 한국정보통신설비학회:학술대회논문집
• /
• 2007.08a
• /
• pp.327-330
• /
• 2007

This article discusses a capacity planning method in QoS-guaranteed IP networks such as BcN (Broadband convergence Network). Since IP based networks have been developed to transport best-effort data traffic, the introduction of multi-service component in BcN requires fundamental modifications in capacity planning and network dimensioning. In this article, we present the key issues of the capacity planning in multi-service IP networks. To provide a foundation for network dimensioning procedure, we describe a systematic approach for classification and modeling of BcN traffic based on the QoS requirements of BcN services. We propose a capacity planning framework considering data traffic and real-time streaming traffic separately. The multi-service Erlang model, an extension of the conventional Erlang B loss model, is introduced to determine required link capacity for the call based real-time streaming traffic. The application of multi-service Erlang model can provide significant improvement in network planning due to sharing of network bandwidth among the different services.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.2 no.2
• /
• pp.22-30
• /
• 2003

Cutting force signals are very useful to evaluate the cutting state, but many disturbing factors are occurring during cutting. For the reliability of the analysis, selecting pure cutting force signals from the original ones is needed. In the current study, using the ICA(Independent Component Analysis) effective cutting force components are seperated from the original signals. And using this, as input data of MLP(Multi-Layer Perception) cutting forces are predicted Experimental results are then compared with the predicted ones to verify the validation of the proposed model.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.20 no.3
• /
• pp.35-43
• /
• 2012

Medium size rotorcraft consist of approximately 5,000 key components. The components must satisfy the target weight and performance requirement through optimization. Therefore a rotorcraft component has approximately 100 times higher unit cost for mass production than the equivalent of an automobile's, along with huge development cost. Configuration management consists of four main parts : configuration identification, configuration control, configuration audit, and data management. In development programme, configuration management is one of the methods to save development cost, and setting a well-structured configuration management system according to the Military Standard is an important factor in success of the programme. The paper proposes a configuration management system suitable for development of various multi-use components development and presents that the configuration management was performed successfully during dual-use component development programme using the established system.

• Journal of the Korean Data and Information Science Society
• /
• v.13 no.2
• /
• pp.87-95
• /
• 2002

In this paper we consider optimal designs of partially accelerated life testing which is devised for multi-component mixed systems with the considerably long lifetime. Test items are run at both use condition and accelerated condition until a specified censoring time. The optimal criterion for the sample-proportion allocated to accelerated condition is to minimize asymptotic variance of the maximum likelihood estimators of the acceleration factor and hazard rates.

• Journal of Positioning, Navigation, and Timing
• /
• v.10 no.1
• /
• pp.29-34
• /
• 2021

Recently, many studies have considered the effect of atmospheric pressure loading (APL) on precise global navigation satellite system (GNSS) data processing. The APL deforms the Earth's crust. It can often exceed 10 mm in radial displacement. In this study, we analyze the APL effect on Multi-GNSS kinematic precise point positioning (PPP). In addition, observations received at two GNSS reference stations (DAEJ and SUWN) in South Korea were processed. The absolute position changes for the two stations were compared to before and after applying the APL effects from January 1 to February 29, 2020. The crust of South Korea was most affected by the APL in the up direction. With the APL model, the difference in daily position changes was mostly within 4 mm in the radial direction. On the other hand, the horizontal components (east-west and north-south) were relatively less affected than the radial component.

• Food Science and Biotechnology
• /
• v.14 no.4
• /
• pp.554-557
• /
• 2005

As a device for taste sensation, an 8-channel taste evaluation system was prepared and applied for discriminant analysis of marketed liquor. The biomimetic polymer membranes for the system were prepared through a casting procedure by employing polyvinyl chloride, bis (2-ethylhexyl)sebacate as plasticizer and electroactive materials such as valinomycin in the ratio of 33:66:1, and were separately attached over the sensitive area of ion-selective electrodes to construct the corresponding taste sensor array. The sensor array in conjunction with a double junction reference electrode was connected to a high-input impedance amplifier and the amplified sensor signals were interfaced to a personal computer via an A/D converter. When the signal data from the sensor array for 3 groups of marketed liquor like Maesilju, Soju and beer were analyzed by principal component analysis after normalization, it was observed that the 1st, 2nd and 3rd principal component were responsible for most of the total data variance, and the analyzed liquor samples were discriminated well in 2 dimensional principal component planes composed of the 1st-2nd and the 1st-3rd principal component.

• Journal of KIISE:Software and Applications
• /
• v.36 no.5
• /
• pp.386-395
• /
• 2009

Business entities with which most service components interact are kind of cross-cutting concerns in a multi-layered distributed application architecture. When business entities are modified, service components related to them should also be modified, even though they implement common functions of the application framework. This paper proposes what we call DTT (Data Type-Tolerant) component model to process the variability of business entities, or externalized data, which feature modern application architectures. The DTT component model expresses the data variability of product lines at the implementation level by means of SCDTs (Self-Contained Data Types) and variation point interfaces. The model improves the efficiency of application engineering through data type converters which support type conversion between SCDTs and business entities of particular applications. The value of this model lies in that data and functions are coupled locally in each component again by allowing service components to deal with SCDTs only instead of externalized business eutities.