• 한국의류학회지
• /
• 제29권6호
• /
• pp.837-846
• /
• 2005

The purpose of this study is to suggest a standard of guidance for testing the performance and safety of motorcycle jacket with built-in airbag. The method of testing were as follows: The effects of the motorcycle jacket with built-in airbag are experimentaly investigated according to neck injury of FMVSS 208. The experiment consists of the crash simulation test by shield and the impact test. The head and neck injuries are evaluated based on industrial standards. Also, the displacements of the head and neck and chest are observed by film analysis. Using the results of the crash simulation test, neck injury$(N_ij)$ is discussed and the peak chest deflection of the results of the impact test, chest injury is pursued. Neck injury$(N_ij)$ of the result of the crash test show that the chance of a serious wound is $18\%$ if rider wear the R&D motorcycle jacket with built-in airbag(Type A). Chest injury is expected by peak chest deflection of the result of the impact test. The result of the peak chest deflection show that the reduction effect in chest injury of Type A motorcycle jacket is $10.3\%$.

• 한국자동차공학회논문집
• /
• 제13권6호
• /
• pp.13-20
• /
• 2005

The most typical fuel control devices of motorcycle engines have carburetors, they are simple in structure and reliable in work. Most of the motorcycle engines have used carburetors in the fuel system, but the fuel economy and the emissions of those engines are bad when we compared with automobile engines. According to stricter emission regulations and higher requirements for fuel economy, the application of the carburetor on the motorcycle engines would be limited. In this paper, we studied about the ECU of motorcycle engine controled by indirect method. A new engine system was designed and experiments were carried out. The experimental results for both carburetor type and ECU type were compared. Maximum torque of $1.053kg{\cdot}m$ at 6500rpm was measured. The engine torque controled using ECU was increased by $10\%$ compared with the carburetor type.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2008년도 정기 학술대회
• /
• pp.573-578
• /
• 2008

Finite element analysis of impact response of a motorcycle helmet is presented in this paper. The finite element LS-DYNA3D code is used to simulate the impact response of the helmet including of plastic shell, foam liner, and magnesium headform. Since the maximum accelerations at center of gravity of the headform obtained by numerical analysis and experiment agree well, the numerical simulation is proved to be valid.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2007년도 정기 학술대회 논문집
• /
• pp.451-456
• /
• 2007

A finite element analysis and experiment study of a motorcycle helmet are presented in this paper. The finite element LS-DYNA3D code is used to analyze the helmet. The test specimen, instruments, and setup procedures are described. Since the displacements and Von-Mises stresses obtained by numerical analysis and experiment agree well, the numerical simulation is proved to be valid.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.2642-2647
• /
• 2007

This study represents numerical study on the thermal and fluid flow characteristics of exhaust gas in a motorcycle muffler. The reference engine was used 124.cc small displacement. Numerical analysis with computational fluid dynamics(CFD) was carried out to investigate the exhaust gas that flow into a motorcycle muffler. The STAR-CD S/W used to three dimensional steady state CFD analysis in a muffler. And than We got the information of static pressure it is used to structural analysis ant the first baffle plate using the commercial CAE code ANSYS workbench. Exhaust gas flow third chamber from frist chamber and running second chamber. A simulation result shows that each chamber of muffler temperature is about 460 K, 445 and 463K and pressure is about 22,000 Pa, 16,000 Pa and 10,000 Pa.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2002년도 춘계학술대회 논문집
• /
• pp.134-139
• /
• 2002

Motorcycle industry, for its competitive position, depends on part design technology. This part design has a bulky amount of data and asks the accumulation of advanced technical skill and experience, and fragmentary technical application is not enough to get to the kernel of a problem. Therefore, the improvement of proper productivity - the starting point of engineering design - and useful Design Methodology for products manufacturing are needed. Thus this paper is aimed to create a program that outputs dynamic characteristics of a vehicle when the data from fully understanding on motorcycle's brake system and induced formula for brake design are inputted.

• 한국공작기계학회논문집
• /
• 제12권1호
• /
• pp.101-110
• /
• 2003

Motorcycle industry, for its competitive position, depends on part design technology. This part design has a bulky amount of data and asks the accumulation of advanced technical skill and experience, and fragmentary technical application is not enough to get to the kernel of a problem. Therefore, the improvement of proper productivity - the starting point of engineering design - and useful Design Methodology for products manufacturing are needed. Thus this paper is aimed to create a program that outputs dynamic characteristics of a vehicle when the data from fully understanding on motorcycle's brake system and induced formula for brake design are inputted. This paper is intended to show a creative design method by the thermal analysis data through FEM study and using shape design parameters derived from our programs.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2011년도 전력전자학술대회
• /
• pp.107-108
• /
• 2011

This paper developed 110cc class electric motorcycle using IPMSM. First, Tractive effort calculated by considering the driving environment of motorcycle. And accordingly the motor and inverter were designed and manufactured. It was mounted on motorcycles and test result was compared with the output power of motorcycle with an internal combustion engine.

• 동력기계공학회지
• /
• 제10권3호
• /
• pp.67-72
• /
• 2006

The effect of manufacturing parameters on wear and improve cooling of motorcycle break system was studied using a disk-on-pad type friction tester. Such parameters conditions have an effect on the wear and improve cooling factor such as applied load, sliding speed, frictional time and number of ventilated disk hole. However, it is difficult to know the mutual relation of these factor. In this study, the wear and cooling characteristics using design of experiment containing 4 elements were investigated for an optimal condition for the best motorcycle disk break system employing Taguchi robust experimental design. From this study, the result was shown that vents have an effect on convection area improving more cooling ability and reduced wear of the disk.

• 한국기계가공학회지
• /
• 제6권4호
• /
• pp.15-21
• /
• 2007

The effect of manufacturing parameters on friction characteristics of motorcycle break system was studied using a disk-on-pad type friction tester. Such parameters conditions have an effect on the frictional factor such as number of ventilated disk hole, applied load, sliding speed, and sliding distance. However, it is difficult to know the mutual relation of these factors. In this study, the friction characteristics using design of experiment containing 4 elements were investigated for an optimal condition for the best motorcycle break system employing regression analysis method. From this study, the result was shown that the applied load in frictional factors was the most important, next to sliding speed, number of ventilated disk hole.