• International Journal of Ocean Engineering and Technology Speciallssue:Selected Papers
• /
• v.6 no.1
• /
• pp.30-37
• /
• 2003

This paper describes vibration control of a suspended system using wave absorption method. A moving multiple-pendulum system and a moving wire-and-load system are treated. The wire-and-load system is extended to a model crane system that has a motor system to roll up and down the suspended mass like a real crane. The same program with different parameter values controls these three systems. Both numerical simulation and experiment have been conducted, and the present control method has shown to be quite effective.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.57.3-57
• /
• 2001

This paper introduces a system which offers the possibility to access remote CAN devices over the Internet as if they were local. The system consists of a local computer and the DSP server. The DSP is connected to a CAN bus with a DC motor and to a Internet simultaneously. The DSP board consists of a LAN controller and a CAN controller. It can convert to a protocol between CAN and Internet. The DSP board is not based on a personal computer. This board is profited a small and light system.

• Journal of Advanced Marine Engineering and Technology
• /
• v.36 no.7
• /
• pp.910-918
• /
• 2012

Carbon monoxide (CO) is a primary air pollutant as an indicator of air quality released from motor vehicle combustion. A comparative study of the distributions of CO concentration with no heat source in two tunnel models open and closed at both end sides is simulated with a commercial CFD code. The tunnel models are used to investigate the CO concentration distributions at three Reynolds numbers, which are computed by the inlet velocities of 0.3, 0.6 and 1.0 m/s. For a better tunnel design, the CFD predictive approaches are available in qualitatively studying the distributions of CO concentration. In the case of the tunnel open at both end sides in sixty seconds, the total CO concentrations are approximately twenty eight percent higher than those in the closed case.

• Journal of Advanced Marine Engineering and Technology
• /
• v.32 no.6
• /
• pp.948-954
• /
• 2008

Now, but task for stringing trolley wire is worked manually by a measurement of dip, we need to development the automatic control system for a safety and effective tasks. In this paper, in works of stringing trolley wire by a mobile of robot, a method is proposed tension control for the stringing trolley wire. On the basics of a wire model with hard nonlinear, ac servo motor model for torque generating and stringing wire tension, the tension control scheme is design and implemented with a detected wire tension by a load cell. We experimentally show that the performance of the tension response are satisfactory to regulator tension. The proposed system is simulated and experimented, results is verified the utilities.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.717-722
• /
• 2003

To improve the shock resistance of the microdrive under non-operating conditions, an isolator was attached to the contacting part of the microdrive. Through FE analysis, design parameters for satisfying the allowable acceleration level of the spindle motor bearing part were presented, which is a most possible critical part of the microdrive.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.519-522
• /
• 2001

In this paper, I propose double parallel manipulator for machining work. And I derive an kinematics by combining the kinematics of the central axis and the kinematics of the link train of linear actuator. The Jacobian of the central axis and the Jacobian of the link train of the linear actuators are induced by a motor algebra and they are combined to an entire Jacobian matrix to transform the velocity of the end effector to those of linear actuators. And then this paper presents the development of control system and user interface program for machining work.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.04a
• /
• pp.957-961
• /
• 1997

In this paper, an assessment has been proceeded about component technology that stamping car panel can be designed and manufactured efficiently. Also this study investigated srandard model of CAD/CAM system in production process of automobile dies. Recently, motor companies are doing their best to increase productivity and to reduce production time. So to develop user-friendly and effective standard model of CAD/CAM system is very important. The obtained results will lead to the reductions in lead time and man-hour required for the design and manufacture of the automobile dies.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.664-669
• /
• 2003

This paper proposes a swing-arm type dual-stage actuator, which consists of a PZT actuator for fine motion and a VCM(Voice Coil Motor) for coarse motion, for SFF ODD(Small Form Factor Optical Disk Drive), in order to achieve fast access speed and precise track following control. We focus our attention on the design and control of the PZT actuator, because there have been a lot of previous researches related to the VCM and dual-stage actuators. Due to the dual cantilever structure, the PZT actuator can generate precise translational tracking motion at its tip where optical pickup is attached at, and the effect of hysteric behavior of the PZT element is reduced. The dynamic model of the PZT actuator is derived by using the Hamilton's principle, and verified by comparing with the experimental frequency response. The sliding mode control is designed in order to be robust against modeling uncertainties. Simulations and experimental results confirm the effectiveness of the suggested control scheme.

• Journal of Mechanical Science and Technology
• /
• v.16 no.5
• /
• pp.639-646
• /
• 2002

In this paper, thrust equations for a rubber belt CVT are derived by considering the geometry and mechanism of the mechanical actuators. In order to solve the thrust equations, an algorithm to calculate the speed ratio is suggested for the given driver speed and load torque based on the actuator characteristic equations and existing formula for the belt thrust forces. Experiments are performed to investigate the driver speed-load torque-speed ratio characteristics at a steady state. The speed and torque efficiencies are measured and used to modify the actuator equations. It is found that the modified equations well predict the steady state characteristics. In addition, the shift dynamic model for a rubber belt CVT is derived experimentally. Simulation results of the CVT shift dynamics are in good accordance with the experiments and it is noted that different coefficients are required to describe the CVT shift dynamics for the upshift and the downshift.

• Journal of Mechanical Science and Technology
• /
• v.20 no.7
• /
• pp.929-940
• /
• 2006

Early detection and diagnosis of incipient induction machine faults increases machinery availability, reduces consequential damage, and improves operational efficiency. However, fault detection using analytical methods is not always possible because it requires perfect knowledge of a process model. This paper proposes a neural network based expert system for diagnosing problems with induction motors using vibration analysis. The short-time Fourier transform (STFT) is used to process the quasi-steady vibration signals, and the neural network is trained and tested using the vibration spectra. The efficiency of the developed neural network expert system is evaluated. The results show that a neural network expert system can be developed based on vibration measurements acquired on-line from the machine.