• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.12
• /
• pp.1721-1724
• /
• 2017

This paper presents a numerical optimization technique to reduce input current and torque ripple of the low voltage BLDC motor using core, coil and switching angle optimization. The optimization technique is employed using the generalized response surface method(RSM) and sampling minimization technique with FEM. A 50W 24V BLDC motor is used to verify the proposed algorithm. As optimizing results, the input current is reduced from 2.46 to 2.11[A], and the input power is reduced from 59 [W] to 51 [W] at the speed of 1000 [rpm]. Also, applied the same optimization algorithm, the torque ripple is reduced about 7.4 %. It is confirmed that the proposed technique is a reasonably useful tool to reduce the consuming current and torque ripple of the low voltage BLDC motor for a compact and efficient design.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.318-319
• /
• 2007

In this study, novel structured thin ultrasonic rotary motor has been proposed. Ultrasonic motors are based on an elliptical motion on the surface of elastic body. ATILA ver. 5.2.4 was used for optimizing stator. The motor was fabricated by using designed stator. And characteristics of the motor were compared with simulated results. When the motor was fabricated with these results, 935[rpm] speed was obtain by input voltage of 25[Vrms] at 93.5[khz].

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.23 no.6
• /
• pp.754-758
• /
• 2017

In this paper, we designed and manufactured an automatic control system to minimize or avoid damage by automatically controlling ship engines in case of fog to allow for safer operation. This automatic power control system uses ATmega128 and an RPM detection circuit to measure RPM changes by artificially generating fog in the fog generator. For this purpose, we have created a complete schematic and applied our source code to an ATmega128 for PWM control using a Hall sensor motor. In future, an experiment and safety evaluation using this automatic power control system with an actual ship will be prepared.

• Progress in Superconductivity and Cryogenics
• /
• v.6 no.3
• /
• pp.33-37
• /
• 2004

This paper presents the construction and test results of an HTS induction motor. End rings and short bars were made of HTS tapes, To increase the efficiency and starting torque, HTS tapes can be used as the rotor bars. Because large current is induced in the rotor circuit, HTS tapes quench and high starting torque can be obtained. As the speed of rotor builds up. HTS tapes which are used as short bars become superconducting state again. After the HTS tapes recover from quench, resistance of the rotor circuit is nearly zero. In that case, power loss in rotor circuit is eliminated. Stator of the conventional induction motor was used as the stator of the HTS motor. Rated capacity of the conventional motor was 0.75 kW. Performances of the HTS induction motor were compared with those of the conventional motor with same volume and specification. Test result showed that the speeds of the HTS induction motor were the same with synchronous speed up to 2.6 Nm and 1.788 rpm at 9.7 Nm. It guarantees the high efficiency of the HTS motor. Starting torque of the HTS motor was more than twice of the conventional motor.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.1
• /
• pp.105-111
• /
• 2013

The spindle is the main component in machine tools. The static and dynamic characteristics of the spindle directly affect the machining accuracy of workpieces. The characteristics of the spindle depend on the shaft size, bearing span, built-in motor location, and so on. Therefore, the appropriate selection of these parameters is important to improve the spindle characteristics. This paper presents the analysis of the static and dynamic characteristics and optimization design of a 40,000-rpm high-speed spindle. Statistical analysis for optimization and finite element analysis were performed. This study uses the response surface method to optimize the objective function and design factors. The targets are the natural frequency and displacement. The design factors are the shaft length, shaft diameter, bearing span, and motor location. The optimized design provides better results than the initial model, and these results are expected to improve the static and dynamic characteristics of the spindle.

• Journal of the Korean Society for Precision Engineering
• /
• v.26 no.5
• /
• pp.79-86
• /
• 2009

Recently PMSM(Permanent magnet synchronous motor) are used for the various direct drive applications such as index table, telescope system and so on. Because the position/speed control performance of direct drive PMSM is directly affected by the torque ripple, there are lots of studies to reduce the cogging torque in the motor design stage. In order to verify the motor design, the reliable cogging torque measurement system is essentially required. The measured motor must be rotated in the constant speed under 1deg/sec so that the cogging torque profile is measured correctly. In this study, the cogging torque measurement system which uses the direct drive PMSM and the speed controller to rotate the measured motor in 0.1rpm(0.6deg/sec) has been developed. Simulink/xPC target was used for the controller and data acquisition system. Based on PI controller, DOB and AFC have been applied to eliminate the low frequency disturbances and the periodic speed ripple. The experimental results show the good performance of the speed regulation for the reference speed 0.1rpm and the reliable profile of the measured cogging torque by the developed speed controller.

• Journal of the Korean Vacuum Society
• /
• v.6 no.S1
• /
• pp.89-95
• /
• 1997

A new type of piexoelectric membrane traveling wave motor has been designed and forbricated. The small motor is composed by the stator which is the combination of annular/circular membrane and metal elastic base using as the common electrode at some time and the rotor which is placed on the metal elastic body. Thus the motor structure is simple and easy to fabricate. The material of a piezoelectric membrane is fabricated by sol-gel method or wear-down method. A piezoelectric traveling wave motor has been fabricated with the stator diameter 8mm The total thickness of the stator is 350$\mu$m. Under the alternative excitation voltage 10-12V the revolving speed of the rotor is more than 100RPM.

• Proceedings of the KIEE Conference
• /
• 1992.07b
• /
• pp.699-702
• /
• 1992

A miniature size electrostatic induction motor have been constructed and studied by applying a three phase ac power source with a maximum voltage of 5 KV and a variable frequency ranged 0.0 - 150 Hz. A maximum no load speed of the motor tested was about 7600 RPM at the applied voltage of 4330 volt and the frequency of 130 Hz for the case of the rotor surface material of polyprophylene sheet screen-printed $TiO_2$ powder on it. It is found that there are 3 different regions of the motor operation, a rotor stop region, a stable operation region and a high speed abnormal region. And it is also found that the motor speed is influenced greatly by the charge relaxation time constant of the rotor surface materials, which however was changed by the means of vapour-deposited Ti or Ni and screen-printed $TiO_2$ powder on the surface of the rotor material, polyprophylene.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.841-845
• /
• 1995

In this study, a motor-integrated high-speed spindle system with .psi. 65mm*25,000rpm is developed by introducing the oil-jet lubrication method,ceramic angular contact ball bearing, a built-in motor and so on. And oil-jet lubrication experiments for evaluating the system performance are performed under various operation conditions. Especially, in order to establish the oil-jet lubrication conditions related to the development of a high-speed spindle system, the effects of oil supply rate and rotational spindle speed are investigated on the temperature rise, temperature distribution,motor current and so on.

• Proceedings of the KIEE Conference
• /
• 1998.11c
• /
• pp.749-751
• /
• 1998

In this study, the wind-mill type ultrasonic motor was fabricated, and then revolution and temperature characteristics of the ultrasonic motor were measured. Brass metal was pressed with umbrella-type using metal mold, then slot of 4 kind was processed in each of thickness. Among sixteen's ultrasonic motors, heat loss on applied voltage was much at stator of the highest resonant point, but heat loss on applied voltage was almost neglected at the lowest resonant point of stator. The thickener thickness of elastic body, revolution speed was decreased. The more slot of elastic body, revolution speed was increased. Applied voltage was changed from $10V_{max}$ to $100V_{max}$. When applied voltage was under $20V_{max}$, ultrasonic motor was not rotated. When applied voltage was over $90V_{max}$, revolution of ultrasonic motor was saturated. Maximum revolution speed was 510[rpm].