• Computers and Concrete
• /
• v.16 no.5
• /
• pp.775-793
• /
• 2015

Moisture transport in concrete in atmospheric environment was studied in this paper. Based on the simplified formula of the thickness of the adsorbed layer, the pore-size distribution function of cement paste was calculated utilizing the water adsorption isotherms. Taking into consideration of the hysteresis effect in cement paste, the moisture diffusivity of cement paste was obtained by the integration of the pore-size distribution. Concrete is regarded as a two-phase composite with cement paste and aggregate, neglecting the moisture diffusivity of aggregate, then moisture diffusivity of concrete was evaluated using the composite theory. Finally, numerical simulation of humidity response during both wetting and drying process was carried out by the finite difference method of partial differential equation for moisture transport, and the numerical results well capture the trend of the measured data.

• Journal of Environmental Health Sciences
• /
• v.24 no.3
• /
• pp.41-47
• /
• 1998

The purpose of this research is evaluation of adsorption capacity of the cast for TCE comparing with the yellow clay. Furthermore, the experimental data was fitted with the Langmuir and Freundlich isotherm and was found to be apllicable to the adsorption isotherm equation. The soil bed reactor used in this study was made of glass(10 cm in diameter, 100 cm in depth). The cast and yellow clay used as adsorbents were screened with 8-20 mesh mecanically. Results from Equilibrium test with adsorbents showed that the equibrium time of the cast and yellow clay was 9min independent of the amount of the adsorbents. The adsorption efficiencys of the cast and yellow clay for TCE was 66.3% and 56.2%, respectively. In the application of Freundlich isotherm, 1/n of the cast and yellow clay were 0.786 and 0.704, respectively. These results showed that the cast was more available than the yellow clay as TCE adsorbent. The best adsorption capacity was showed at 0% moisture content, 70 ppm inlet concentration and 25$^{\circ}$C temperature.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.45 no.8
• /
• pp.1153-1161
• /
• 2016

For prevention of moisture adsorption, the fermented red ginseng extract spherical granules were coated by using hydrophobic fractions. The hydrophobic parts were extracted from red ginseng such as the perfect soluble part in 90% ethanol (PSE) and non-soluble part in hot water (NSHW). The optimum operating conditions for making fermented red ginseng extract spherical granules coated with PSE were a feeding rate (FR) of 0.49 mL/min, atomization air pressure (AP) of 2.14 bar, and product temperature (PT) of $48.96^{\circ}C$., whereas conditions for granules coated with NSHW were a FR of 0.61 mL/min, AP of 2.75 bar, and PT of $46.30^{\circ}C$. The solubility of coated fermented red ginseng extract spherical granule was lower than that of not coated. The fermented red ginseng extract spherical granules coated with NSHW showed more preventative effects for moisture adsorption than those coated with PSE, although there were no differences in solubility and fluidity. In the sensory evaluation, granules coated with hydrophobic fractions extracted from red ginseng were shown to be bitterer and less soluble than those not coated spherical granules. In conclusion, fermented red ginseng extract spherical granules coated with hydrophobic extracts from red ginseng showed a preventative effect against moisture.

• Food Science and Preservation
• /
• v.10 no.3
• /
• pp.297-301
• /
• 2003

The hardness of corrugated packaging box decreased during storage period because of high humidity. Therefore, the strength-decreasing factor of corrugated packaging box had to be investigated to determine the compression strength of the corrugated packaging box. This study was conducted to define the characteristics of moisture absorption as well as compression strength of corrugated fiberboard. (1) The moisture content of the corrugated fiberboard was rarely influenced by the kinds of raw materials and water repellent. However, the moisture adsorption of the corrugated fiberboard was shown to be clearly affected by air temperature changes. (2) The moisture content of the corrugated fiberboard was significantly affected by relative humidity. The moisture adsorption of corrugated fiberboard was also greatly influenced by composition of raw materials rather than water repellent. The results indicated that the improvement of raw materials was more effective than the increase of water repellent of corrugated fiberboard to reduce the moisture adsorption of the corrugated fiberboard. (3) The vertical compression strength was significantly decreased with increasing relative humidity. The reduction rate of vertical compression strength was not charged with the increase of relative humidity, which was regardless of kinds of corrugated fiberboard. (4) For improving the strength of the corrugated packaging box, new technique should be found to develop better quality of raw materials. Moreover, the physical construction of corrugated packaging box should be clearly understood because the corrugated packaging box for the agricultural products was usually used for the circumstances of high humidity and low air temperature

• Journal of Korean Society for Atmospheric Environment
• /
• v.26 no.3
• /
• pp.286-297
• /
• 2010

This study deals with the effect of pretreatment on the $CO_2$ adsorption capacity of zeolitic adsorbents including a commercial A-type zeolite and cation exchanged adsorbents. The pre-heating could change the intrinsic properties such as specific surface area and adsorption capacity of the adsorbent. As a result of the experiment, the moisture previously filled inside might affect the potential adsorption capacity of the adsorbent, and could be disappeared throughout the heat treatment. An optimum pretreatment temperature for the test adsorbent was found to be $400^{\circ}C$, at which temperature enabled more than 90% refreshment. Precise examination through the TPD test showed that the TSA (Temperature Swing Adsorption) process would be desirable in dry adsorption of $CO_2$.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.29 no.3
• /
• pp.142-147
• /
• 2017

Improvement of the enthalpy exchange element's energy efficiency is of current interest from anenergy-saving viewpoint. In this study, a LiCl-impregnated spacer was devised as a means to improve the performance of the enthalpy exchange element. Two samples were tested : one with and one without impregnated spacers of $338{\times}338{\times}380mm$ sizes with 2.0 mm channel spacing. The results showed that the temperature efficiencies of the two samples were approximately the same. The humidity efficiency, however, was strongly affected by the LiCl impregnation. The impregnated sample yielded a 9% higher humidity efficiency under cooling and the difference increased to 14% under aheating condition. It was anticipated that more moisture would beadsorbed on the LiCl-impregnated spacers, which was delivered to their roots and eventually to the air in neighboring channels. Separate moisture adsorption tests revealed that both the adsorption rate and the amount of the adsorbed moisture are higher for the LiCl-impregnated specimen.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2020.06a
• /
• pp.138-139
• /
• 2020

With the rapid progress of industrialization, indoor air quality is a very important factor for modern people who spend most of their day indoors. The recent issue of fine dust and radon on the portal site's popularity search shows that interest in indoor air quality has increased. Fine dust causes respiratory diseases, and radon causes severe lung cancer. The new material was tested using plant activated carbon, palm activated carbon and bamboo activated carbon. Both palm activated carbon and bamboo activated carbon are porous materials and generate smooth physical adsorption. As a result of the experiment, both the activated carbon tends to gradually decrease in strength and fluidity as the replacement ratio increases. The reason for this is that both activated carbons have the property of absorbing moisture, so it is judged that the strength is lowered by absorbing moisture necessary for curing. In the case of fluidity, it is judged that the fluidity is reduced by absorbing the moisture required for the flow. In the future, if the problem of the color of the finished cured body is compensated, it will be possible to manufacture a functional finishing board to replace the existing interior finishing material.

• Proceedings of the Korean Society of Tobacco Science Conference
• /
• 2005.10a
• /
• pp.30-30
• /
• 2005

• Korean Chemical Engineering Research
• /
• v.53 no.3
• /
• pp.401-406
• /
• 2015

Getter is a class of materials used in absorbing gases such as hydrogen and moisture in microelectronics or semiconductor devices to operate properly. In this study, we developed a new device structure consisting of porous anodized alumina films on textured silicon wafer, which have cost efficiency in materials and processing aspects. Anodic aluminum oxide (AAO) with controlled pore sizes can be applied to a high-efficiency moisture absorber due to the high surface area and OH- saturated surface property. The moisture sorption capacity was 2.02% (RH=35%), obtained by analyzing isothermal adsorption/desorption curve.

• Journal of the Korean Wood Science and Technology
• /
• v.51 no.5
• /
• pp.321-333
• /
• 2023

In this study, lignin, a lignocellulosic biomass, was chemically modified to produce polyethyleneimine-grafted lignin (PKL) with maximum hexavalent chromium [Cr(VI)] adsorption capacity. Changes in the physicochemical properties due to the cationization of lignin were confirmed through elemental analysis, Fourier transform infrared spectroscopy, and moisture stability evaluation. Alginate (Alg) beads containing PKL (Alg/PKL) were prepared by incorporating cationic lignin into the Alg matrix to apply the prepared PKL in a batch-type water treatment process. The optimal Alg/lignin mixing ratio was selected to increase the Cr(VI) adsorption capacity and minimize lignin elution from the aqueous system. The selected Alg/PKL beads exhibited an excellent Cr(VI) removal capacity of 478.98 mg/g. Isothermal adsorption and thermodynamic analysis revealed that the Cr(VI) removal behavior of the Alg/PKL beads was similar to that of heterogeneous chemical adsorption. In addition, the bulk adsorbent material in the form of beads exhibited adsorption behavior in three stages: surface adsorption, diffusion, and equilibrium.