본 연구에서는 5종류의 플라이애쉬를 포함한 초유동 콘크리트와 3종류의 일반 콘크리트에 대한 재료물성을 측정하여 서로 비교.분석하였다. 경화 전의 물성측정을 위해서 슬럼프 실험, 슬럼프 플로우 실험, O형 깔대기 실험, 박스 충전성 실험, L형 충전성 실험을 수행하였고 경화 후의 물성측정을 위해 압축강도 실험, 할렬인장강도 실험, 탄성계수 실험, 크리프 실험, 건조수축 실험 등을 수행하였다. 경화전의 물성측정 실험결과들을 바탕으로 초유동 콘크리트와 일반 콘크리트의 유동성과 충전성을 평가하였고 두 결과를 비교.분석하였다. 또한 경화 후의 물성측정 실험결과를 통하여 초유동 콘크리트의 재료역학적인 특성을 파악하였다. 자기충전성을 만족시킬만한 유동성과 작업성을 가지면서 40 MPa이상의 28일 압축강도를 갖는 양호한 재료역학적인 특성을 나타내는 초유동 콘크리트의 개발 가능성을 보였다. 일반적으로 초유동 콘크리트의 크리프 변형량은 일반 콘크리트보다 상대적으로 작았지만 건조수축은 일반 콘크리트보다 30%이상 컸다.
Surplus water inside a concrete other than moisture that is used for hydration of the cement affects the physical properties of the concrete (modulus of elasticity, compressive strength, drying shrinkage, and creep) by drying. Changes in temperature and humidity inside a concrete has correlation with the movement speed and reaction rate of deterioration factors such as carbon dioxide and chloride ions. In this study, comparison was performed between temperature and relative humidity inside the concrete and meteorological data for exposure environment through measurement at the site for two years. Surface temperature of the concrete (depth 1cm) was measured higher by 6℃ during the summers, while it was measured lower by 2℃ during the winters due to solar radiation, wind, and radiation cooling. As for relative humidity, change was large in the depth of 1cm, while more than 85% was maintained in the depth of 10cm.
콘크리트 중의 골재가 차지하는 비율은 약 70~80 vol%로서 콘크리트의 고온 역학적 성상에 큰 영향요소로 작용할 수 있다. 이 연구는 고온시 콘크리트의 역학적 특성을 평가하기 위한 일환으로써 다양한 환경조건, 즉 고온조건, 하중조건에 따른 역학적 특성을 비교하기 위하여 목표강도 60 MPa급 보통 골재 및 경량 골재 콘크리트를 대상으로 선정하였다. 사용된 시험체는 ${\phi}100{\times}200mm$로서 상온 압축강도의 0%, 20%, 40% 하중을 재하한 상태에서 고온에 따른 강도, 탄성계수, 열팽창 변형(thermal strain), 전체 변형(total strain), 내력저하수축(transient creep) 등 고온에서의 역학적 특성을 평가하였다. 시험 결과 골재의 열팽창계수가 작은 경량 콘크리트는 열팽창 변형이 일반 골재를 사용한 콘크리트에 비하여 전반적으로 작게 나타났으며, 고온조건인 $700^{\circ}C$에서도 압축강도 저하가 상온강도에 대하여 80% 수준으로 나타났다. 또한 재하에 의한 내력저하수축은 $500^{\circ}C$를 기준으로 콘크리트의 변형을 팽창에서 수축으로 전환시키는 영향요인으로써, 콘크리트와 골재의 열팽창 변형비(concrete /aggregate)가 수축의 경향이 큰 경우 콘크리트의 내력저하가 적은 경향을 확인할 수 있었다.
복합구조의 합성단면에서 콘크리트 크리프변형은 합성단면에 추가 변형을 발생시키며, 장기변형의 일부 구속에 의한 응력이완은 콘크리트단면에 도입된 선압축응력의 심각한 손실을 초래할 수 있다. 이 논문에서는 복잡한 합성단면의 콘크리트 크리프변형에 대해 공학적인 목적에서 단순 해석이 가능한 이완계수법을 유도하고, 이완계수법에 요구되는 응력이완계수 식을 제안하였다. 이완계수법은 크리프계수와 합성단면의 환산단면특성 및 하중특성을 매개변수로 사용하는 균등 크리프계수 단계별계산법(CC-SSM)과 같은 방법으로 유도되었다. 제안된 이완계수 식에 의한 응력이완계법의 오차는 CC-SSM으로부터 평가된 이완계수법의 평균 응력이완계수에 의한 오차보다 향상되었으며, 자유상태에서 크리프변형에 대한 제안식에 의한 이완계수법 반응의 평균오차율은 3보다 크지 않은 크리프계수에 대해 1.2%보다 작으며, 99% 신뢰도에서 최대 3.3%이었다. 제안된 응력이완계수 식은 크리프변형에 대한 합성단면의 내부구속 정도를 반영하며, 외부구속 효과를 분석하기 위한 전산구조해석에서 응력이완계수가 적용된 유효탄성계수는 합성단면의 요소에 대한 강성 계산에 효율적으로 적용될 수 있다.
이 논문의 목적은 산업부산물인 플라이애쉬의 재활용을 높이기 위해 플라이애쉬를 대량으로 사용한 플라이애쉬 경화체를 제작 하였다. 단위시멘트량의 90%를 플라이애쉬로 대체하여 제작한 이 경화체의 압축강도, 탄성계수 등 기초적인 물성을 파악하여 구조용 건설재료로 실용화하기 위한 기초적 자료를 제시하고자 한다. 물-시멘트비를 변수로 하여 플라이애쉬 경화체의 휨강도를 측정한 결과 물-결합재비, 잔골재율이 증가할수록 파괴에너지가 감소하였다. 이러한 이유는 파괴에너지가 강도의 영향을 크게 받기 때문으로 판단된다. 이번 실험으로 플라이애쉬 경화체의 기초물성은 기존 콘크리트에 많이 접근했음을 알 수 있었다. 하지만 구조용 건설자재로 도입되기 위해서는 건조수축, 크리프, 동결융해 등의 내구성 실험도 계속 수행되어야 할 것이다.
화재시 콘크리트 구조물은 구성재료의 상이한 열적특성으로 인해 강도가 저하하고 동시에 수직부재는 수평부재의 팽창에 의한 모멘트하중을 받아 전단파괴가 발생한다. 따라서 여러가지 화재곡선을 사용한 콘크리트 구조물의 화재시 거동에 대한 연구가 많이 이루어졌지만 주로 온도상승구간에서 발생하는 폭렬특성과 열팽창변형에 관한 연구가 대부분이다. 하지만 고온이 유지될 경우 발생할 수 있는 크리프변형은 화재시 구조물의 안정성에 큰 영향을 미치지만 상대적으로 연구가 미진한 상태이다. 또한 이러한 고온을 받는 콘크리트의 안정성에는 체적의 대부분을 차지하는 굵은골재의 열적특성이 큰 영향을 미치기 때문에 이 연구에서는 화강암계, clay계, clay-ash계 세 종류의 굵은골재를 사용한 콘크리트의 고온 역학적 특성을 평가했다. 그 결과 굵은골재의 성인으로 인한 내부공극 때문에 경량골재를 사용한 콘크리트가 일반골재를 사용한 콘크리트보다 높은 고온강도 및 탄성계수를 나타냈고 열팽창변형과 전체변형의 경우 더 낮은 변형률을 나타내어 온도상승구간에서의 구조적 안정성 측면에서 유리한 것으로 판단되었다. 그러나 고온크리프의 경우 내부공극으로 인해 더 큰 수축량이 발생하기 때문에 내화성능설계시에 이에 대한 추가적인 고려가 필요할 것으로 판단되었다.
Prediction of prestressed concrete girder integral abutment bridge (IAB) load effect requires understanding of the inherent uncertainties as it relates to thermal loading, time-dependent effects, bridge material properties and soil properties. In addition, complex inelastic and hysteretic behavior must be considered over an extended, 75-year bridge life. The present study establishes IAB displacement and internal force statistics based on available material property and soil property statistical models and Monte Carlo simulations. Numerical models within the simulation were developed to evaluate the 75-year bridge displacements and internal forces based on 2D numerical models that were calibrated against four field monitored IABs. The considered input uncertainties include both resistance and load variables. Material variables are: (1) concrete elastic modulus; (2) backfill stiffness; and (3) lateral pile soil stiffness. Thermal, time dependent, and soil loading variables are: (1) superstructure temperature fluctuation; (2) superstructure concrete thermal expansion coefficient; (3) superstructure temperature gradient; (4) concrete creep and shrinkage; (5) bridge construction timeline; and (6) backfill pressure on backwall and abutment. IAB displacement and internal force statistics were established for: (1) bridge axial force; (2) bridge bending moment; (3) pile lateral force; (4) pile moment; (5) pile head/abutment displacement; (6) compressive stress at the top fiber at the mid-span of the exterior span; and (7) tensile stress at the bottom fiber at the mid-span of the exterior span. These established IAB displacement and internal force statistics provide a basis for future reliability-based design criteria development.
The mechanical and rheological properties of agricultural materials are important for engineering design and analysis of their mechanical harvesting, handling, transporting and processing systems. Agricultural materials, which composed of structural members and fluids do not react in a purely elastic manner, and their response when subjected to stress and strain is a combination of elastic and viscous behavior so called viscoelastic behavior. Many researchers have conducted studies on the mechanical and rheological properties of the various agricultural products, but a few researcher has studied those properties of rice plant, and also those data are available only for foreign varieties of rice plant. This study are conducted to experimentally determine the mechanical and the rheological properties such as axial compressive strength, tensile strength, bending and shear strength, stress relaxation and creep behavior of rice stems, and grain detachment strength. The rheological models for the rice stem were developed from the test data. The shearing characteristics were examined at some different levels of portion, cross-sectional area, moisture content of rice stem and shearing angle. The results obtained from this study were summarized as follows 1. The mechanical properties of the stems of the J aponica types were greater than those of the Indica ${\times}$ Japonica hybrid in compression, tension, bendingand shearing. 2. The mean value of the compressive force was 80.5 N in the Japonica types and 55.5 N in the Indica ${\times}$ Japonica hybrid which was about 70 percent to that of the Japonica types, and then the value increased progressively at the lower portion of the stems generally. 3. The average tensile force was about 226.6 N in the Japonica types and 123.6 N in the Indica ${\times}$ Japonica hybrid which was about 55 percent to that of the Japonica types. 4. The bending moment was $0.19N{\cdot}m$ in the Japonica types and $0.13N{\cdot}m$ in the Indica ${\times}$ Japonica hybrid which was 68 percent to that of the Japonica types and the bending strength was 7.7 MPa in the Japonica types and 6.5 MPa in the Indica ${\times}$ Japonica hybrid respectively. 5. The shearing force was 141.1 N in Jinju, the Japonica type and 101.4 N in Taebaeg, the Indica ${\times}$ Japonica hybrid which was 72 percent to that of Jinju, and the shearing strength of Taebaeg was 63 percent to that of Jinju. 6. The shearing force and the shearing energy along the stem portion in Jinju increased progressively together at the lower portions, meanwhile in Taebaeg the shearing force showed the maximum value at the intermediate portion and the shearing energy was the greatest at the portion of 21 cm from the ground level, and also the shearing strength and the shearing energy per unit cross-sectional area of the stem were the greater values at the intermediate portion than at any other portions. 7. The shearing force and the shearing energy increased with increase of the cross-sectional area of the rice stem and with decrease of the shearing angie from $90^{\circ}$ to $50^{\circ}$. 8. The shearing forces showed the minimum values of 110 N at Jinju and of 60 N at Taebaeg, the shearing energy at the moisture content decreased about 15 percent point from initial moisture content showed value of 50 mJ in Jinju and of 30 mJ in Taebaeg, respectively. 9. The stress relaxation behavior could be described by the generalized Maxwell model and also the compression creep behavior by Burger's model, respectively in the rice stem. 10. With increase of loading rate, the stress relaxation intensity increased, meanwhile the relaxation time and residual stress decreased. 11. In the compression creep test, the logarithmic creep occured at the stress less than 2.0 MPa and the steady-state creep at the stress larger than 2.0 MPa. 12. The stress level had not a significant effect on the relaxation time, while the relaxation intensity and residual stress increased with increase of the stress level. 13. In the compression creep test of the rice stem, the instantaneous elastic modulus of Burger's model showed the range of 60 to 80 MPa and the viscosities of the free dashpot were very large numerical value which was well explained that the rice stem was viscoelastic material. 14. The tensile detachment forces were about 1.7 to 2.3 N in the Japonica types while about 1.0 to 1.3 N in Indica ${\times}$ Japonica hybrid corresponding to 58 percent of Japonica types, and the bending detachment forces were about 0.6 to 1.1 N corresponding to 30 to 50 percent of the tensile detachment forces, and the bending detachment of the Indica ${\times}$ Japonica hybrid was 0.1 to 0.3 N which was 7 to 21 percent of Japonica types. 15. The detachment force of the lower portion was little bigger than that of the upper portion in a penicle and was not significantly affected by the harvesting period from September 28 to October 20. 16. The tensile and bending detachment forces decreased with decrease of the moisture content from 23 to 13 percent (w.b.) by the natural drying, and the decreasing rate of detachment forces along the moisture content was the greater in the bending detachment force than the tensile detachment force.
기둥축소량을 발생시키는 원인과 현재까지 연구되어온 코드에 대하여 고찰하였다. 코드에서 언급하고 있는 내용들은공시체의 건조수축, 크리프, 압축강도 및 탄성계수 그리고 구조해석에서 산출되는 탄성변형을 다루고 있으나, 장기간의 모니터링에 의해 나타나는 온도에 의한 변형은 기존의 연구에 의해 발생되는 요소들에 의한 것보다 축소량이 적게 발생하는 것을 알 수 있었다. 하지만 기존의 연구에서는 온도에 의한 변형에 대해서는 고려하지 않고 건조수축, 크리프 및 탄성변형에 대하여 다루고 있는 것을 확인 할 수 있고, 공시체의 실험에 대해서는 온도에 대한 항목은 습도에 대한 항으로 대체하여 다루고 있음을 알 수 있다. 이에 대해 제안식에 의한 보정수치는 축소량 산정시 상부방향 4.9 mm 와하부방향 1.0 mm의 오차를 나타내어 측정에 의한 수치와 거의 일치하는 것으로 나타났다. 따라서, 기존의 기둥축소량 산정에 있어서 누락될 수 있는 온도에 대하여 추가적으로 더 연구하여 그 영향계수를(수직온도보정계수, ${\beta}_{vT}$) 고려하고, 공시체의 시험뿐만 아니라 구조체의 온도보정에 관한 기준 보완이 필요한 것으로 파악되었다.
In the present paper a transient three-dimensional thermo-mechanical model for concrete is presented. For given boundary conditions, temperature distribution is calculated by employing a three-dimensional transient thermal finite element analysis. Thermal properties of concrete are assumed to be constant and independent of the stress-strain distribution. In the thermo-mechanical model for concrete the total strain tensor is decomposed into pure mechanical strain, free thermal strain and load induced thermal strain. The mechanical strain is calculated by using temperature dependent microplane model for concrete (O$\check{z}$bolt, et al. 2001). The dependency of the macroscopic concrete properties (Young's modulus, tensile and compressive strengths and fracture energy) on temperature is based on the available experimental database. The stress independent free thermal strain is calculated according to the proposal of Nielsen, et al. (2001). The load induced thermal strain is obtained by employing the biparabolic model, which was recently proposed by Nielsen, et al. (2004). It is assumed that the total load induced thermal strain is irrecoverable, i.e., creep component is neglected. The model is implemented into a three-dimensional FE code. The performance of headed stud anchors exposed to fire was studied. Three-dimensional transient thermal FE analysis was carried out for three embedment depths and for four thermal loading histories. The results of the analysis show that the resistance of anchors can be significantly reduced if they are exposed to fire. The largest reduction of the load capacity was obtained for anchors with relatively small embedment depths. The numerical results agree well with the available experimental evidence.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.