• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.12
• /
• pp.1259-1263
• /
• 2004

In this paper, the optimum design of ultrasonic dry cleaning head was investigated. The transducer instead of mechanical dynamic structure was used to generate ultrasonic wave and the horn-shape amplifier was utilized to solve the energy decaying problem of ultrasonic wave with propagating it through the media. The analyses of ultrasonic wave and a fluid for the selected structure of a cleaning head were carried out using SYSNOISE and ANSYS simulators, respectively. Based on simulator results, the distance between a horn and the substrate of 4 mm and the horn diameter of 10 mm were determined to maximize the energy of ultrasonic waves. The cooling structure was also considered to reduce the heat from the transducer and the horn. The equivalent circuit for the fabricated horn was deduced from HP4194A impedance/gain/phase analyzer and the frequency of an ultrasonic wave of 20.25 kHz was confirmed using the parameters of the equivalent circuit.

• Journal of Advanced Marine Engineering and Technology
• /
• v.28 no.7
• /
• pp.1072-1081
• /
• 2004

This paper is to investigate on the effects of the hole size of spring type EFV(excessive flow valve) for automobiles The analytical and experimental methods were employed to measure the discharge coefficient. choked flowrate and Pressure wave in a bombe, line and vaporizor The size of EFV was determined to meet the legally permitted limits with the capacity of engine displacement up to 2000cc, according to the obtained discharge coefficient. The Purpose of this paper is 1) to find causes of bad acceration performance in LPG engines 2) to find optimal design determination of spring coefficient and orifice hole size of excessive flow valve in LPG engine 3) to find pressure wave of bombe, line and vaporizer through expeimental verification. Experimental results indicated that increase of orifice size 0.5mm to 1mm be caused to increase discharge coefficient, and choked flow rate and decrease operation range of difference pressure wave.

• Proceedings of the IEEK Conference
• /
• 2000.07b
• /
• pp.1009-1012
• /
• 2000

In this paper, we have designed and fabricated power PHEMT’s with an unit gate width of 80$\mu\textrm{m}$ and 4 fingers, and MIMIC power amplifiers using the PHEMT’s as well. The PHEMT’s have a 0.2$\mu\textrm{m}$ gate length and source to drain spacing of 3$\mu\textrm{m}$. The characteristics of the fabricated PHEMT’s are 4.08dB of S$\sub$21/ gain at the 35GHz and 317mS/mm of gm, and 62GHz of f$\sub$T/ and 120GHz of f$\sub$max/. The designed and fabricated MIMIC’s power amplifiers with 6 PHEMT’s and MIN capacitors were fully passivated by 1000 Α of Si$_3$N$_4$ film for higher performance and surface protects. The chips were processed using the MINT processes, and size was 3.25 ${\times}$ 1.8$\textrm{mm}^2$. The fabricated MIMIC power amplifiers have RF characteristics such as 11.25dB of S$\sub$21/ gain, 11.37dB of input return-loss and 12.69dB of output return-loss at the 34.55GHz.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.36 no.1
• /
• pp.9-17
• /
• 2016

The elastic modulus of a 3D-printed Kelvin foam plate is investigated by measuring the acoustic wave velocity of 1 MHz ultrasound. An isotropic tetrakaidecahedron foam with 3 mm unit cell is designed and printed layer upon layer to fabricate a Kelvin foam plate of 14 mm thickness with a 3D CAD/printer using ABS plastic. The Kelvin foam plate is completely filled with paraffin wax for impedance matching, so that the acoustic wave may propagate through the porous foam plate. The acoustic wave velocity of the foam plate is measured using the time-of-flight (TOF) method and is used to calculate the elastic modulus of the Kelvin foam plate based on acousto-elasticity. Finite element method (FEM) and micromechanics is applied to the Kelvin foam plate to calculate the theoretical elastic modulus using a non-isotropic tetrakaidecahedron model. The predicted elastic modulus of the Kelvin foam plate from FEM and micromechanics model is similar, which is only 3-4% of the bulk material. The experimental value of the elastic modulus from the ultrasonic method is approximately twice as that of the numerical and theoretical methods because of the flexural deformation of the cell edges neglected in the ultrasonic method.

• Current Optics and Photonics
• /
• v.2 no.2
• /
• pp.179-184
• /
• 2018

Terahertz (THz) wave generation by periodically poled $BaTiO_3$ (PPBT) with a quasi-phase-matching (QPM) scheme based on cascaded difference-frequency generation (DFG) is theoretically analyzed. The cascaded DFG processes comprise cascaded Stokes and anti-Stokes processes. The calculated results indicate that the cascaded Stokes processes are stronger than the cascaded anti-Stokes processes. Compared to a noncascaded Stokes process, THz intensities from $20^{th}$-order cascaded Stokes processes increase by a factor of 30. THz waves with a maximum intensity of $0.37MW/mm^2$ can be generated by $20^{th}$-order cascaded DFG processes when the optical intensity is $10MW/mm^2$, corresponding to a quantum conversion efficiency of 1033%. The high quantum conversion efficiency of 1033% exceeds the Manley-Rowe limit, which indicates that PPBT is an excellent crystal for THz wave generation via cascaded DFG.

• Journal of the Korean Wood Science and Technology
• /
• v.31 no.3
• /
• pp.35-41
• /
• 2003

The mechanical and physical properties of wood are strongly dependent upon the slope of grain. Specially, tensile strength is more severely affected by the slope of grain. Therefore, tension tests were performed on small thin wood samples made from Pinus radiata with varying the slope of grain. Determining the tensile strength for clear thin wood samples the other variabilities associated with material, size, drying, defects, etc were discarded. Slope of grain was measured by the slope of grain indicator and actual slope of grain was also determined by a protractor. Correlation coefficients between machine measured and actual slope of grain for 40 pieces of 2×20 mm, 300 mm long Pinus radiata were 0.84 for wide face measurement. Results also showed that tensile strength and MOE from stress wave tests decreased with increasing the slope of grain. This study did not establish a relationships for tensile strength and MOE from stress wave with slope of grain. However, the trends of MOEs from stress wave test with both slope of grain are agreed well with Hankinson's equation. Predicted tension strength curve by Hankinson's equation was also agreed well with the experimental data over the range from 0 to 13 degrees for slope of grain.

• Journal of Electrochemical Science and Technology
• /
• v.15 no.3
• /
• pp.373-387
• /
• 2024

The layout of the cathode flow field largely determines the net output power of the proton exchange membrane fuel cell (PEMFC). To make the normal mass transfer effect best, the longitudinal channel was waved based on four serpentine flow channels, and the effects of sag depth and longitudinal channel width on the output efficiency of the cell were explored. The results show that the wave channel design systematically enhances the forced convection between adjacent channels, which can prevent a large zone of oxygen starvation zone at the outlet of the channel. The increase of the normal velocity in the gas transmission process will inevitably induce a significant enhancement of the mass transfer effect and obtain a higher current density in the reaction zone. For the longitudinal channel width, it is found that increasing its size in the effective range can greatly reduce the channel pressure drop without reducing the output power, thereby improving the overall efficiency. When the sag depth and longitudinal channel width gradient are 0.6 mm and 0.2 mm respectively, PEMFC can obtain the best comprehensive performance.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.11
• /
• pp.1224-1230
• /
• 2007

Recently, wireless LAN are often applied in home or office because of its various of convenience. Frequency rage of wireless LAN specified by IEEE 802.11a is at 5.2 GHz and IEEE 802.11b is 2.4 GHz. But in offices with wireless LAN devices, reflection of waves against walls, ceilings, floors and desks made of metal creates multipath problems that reduce communication speed and lose data. These problems can be solved by using EM wave absorber. In this paper, we designed and fabricated EM wave absorbers using MnZn-ferrite, sendust, carbon and CPE(Chlorinated Polyethylene). The EM wave absorber with the ratio of MnZn-Ferrite : sendust : CPE=64 : 16 : 20 wt.% has thickness of 3.7 mm and absorption ability more than 17 dB at 2.4 GHz and the EM wave absorber with the ratio of MnZn-ferrite : carbon : CPE=40 : 15 : 45 wt.% has thickness of 3.8 mm and absorption ability more than 23 dB at 5.2 GHz.

• Kosin Medical Journal
• /
• v.33 no.3
• /
• pp.328-336
• /
• 2018

Objectives: Electrocardiograhy (ECG) is the first step in hypertrophic cardiomyopathy (HCMP) diagnosis. For various reasons, the T wave inversion (TWI) and ECG change with time and HCMP is not easy to diagnosis. The aim of this retrospective study was to investigate the association between TWI on ECG and apical HCMP. Methods: A total of 4,730 ECGs presenting TWI from January 2011 to March 2013 in Pusan National University Hospital were enrolled. 133 patients who were examined by both echocardiography and coronary angiogram were analyzed. Patients were divided into two groups: Group A (TWI ${\geq}$ 10 mm) and Group B (5 mm ${\leq}$ TWI < 10 mm). HCMP is defined by a wall thickness ${\geq}15mm$ in one or more LV myocardial segments. Apical HCMP is defined to be hypertrophy that is confined to LV apex. The patients who had ECGs with at least one month interval were divided 3 groups: Normal T wave, Abnormal T wave, and Persistent TWI. The prevalence of Apical HCMP and coronary artery disease (CAD) was reviewed among the three groups. Results: In this study there were a total 133 patients, with patients divided into Group A which had 15 patients and Group B which had 118 patients. Among the 23 patients with apical HCMP, three patients were Group A and twenty patients were Group B (P = 0.769). Regarding constancy of TWI, persistent TWI group was higher in apical HCMP than in other groups (P = 0.038). CAD had no difference between groups (P = 0.889). Conclusions: T wave negativity was not associated with incidence of apical HCMP. However, apical HCMP was diagnosed more frequently in patients with persistent TWI. Further follow up echocardiographic study is needed to evaluate the progression of apical HCMP in patients with TWI.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.22 no.8
• /
• pp.1733-1739
• /
• 1997

An ultra-compact milimeter-wave broadband MMIC amplifier was designed using a direct-coupled topology combined with optimum feedback design. Significant reductionin the chip size was possible by employing the direct-coupled topology. Bias resistors required for the direct-coupled topology were also used as feedback elements. Feedback was optimized for millimeter-wave frequencies using reactive elements. The fabricated MMIC amplifier was realized in a chip size of 0.8mm$^{[-992]}$ and showed gains higher than 8 dB from 12 to 44 GHz. An output power of 30mW was achieved at 44 GHz with a drain efficiency of 10%.