• Membrane and Water Treatment
• /
• v.9 no.4
• /
• pp.255-262
• /
• 2018

This study attempted to evaluate the process of self-forming dynamic membrane formation on mesh filter in membrane bioreactor with a two-stage method of batch (agitation) and continues (aeration) stage at different sludge concentrations. Four concentrations of activated sludge including $6{\pm}0.4$, $8{\pm}0.5$, $10{\pm}0.3$, $14{\pm}0.3g/L$ were used to demonstrate the optimal concentration of sludge for treating municipal wastewater and reducing fouling in dynamic membrane bioreactor. The formation time and effluent turbidity were decreased in the batch stage when increasing the activated sludge concentration. The minimum values of formation time and effluent turbidity were 14 min and 43 NTU for the optimum mixed liqueur suspended solids of $8{\pm}0.5g/L$, respectively. To improve operational condition and fouling reduction in the aeration stage, critical fluxes were measured for all concentrations by flux-step method. With increasing the sludge concentration, the relevant critical fluxes reduced. The optimum subcritical flux of $30L/m^2/h$ was applied as operating flux in the second stage. The maximum COD removal efficiency of 98% was achieved by the concentration of $8{\pm}0.5g/L$. Compressibility index of self-forming dynamic membrane and transmembrane pressure trend remained somewhat constant until the optimal concentration of $8{\pm}0.5g/L$ and thereafter they increased steeply.

• Journal of the Korean institute of surface engineering
• /
• v.50 no.6
• /
• pp.510-515
• /
• 2017

In this study, a transient liquid phase sintering (TLPS) process of Ag pastes mixed with a fusible metal alloy of Bi58Sn42 with the melting temperature of $138^{\circ}C$, was examined. After screen printing of the Ag pastes with and without Bi58Sn42 powders on polyimide (PI) substrates, the electrodes were heat-treated at different temperatures in the range between 150 and $300^{\circ}C$ for 60 min in air. Comparing the electrical conductivity of the Ag pastes with and without Bi58Sn42 alloy powder after the heat treatment, it was manifested that the low melting temperature alloy definitely played a major role in an increased conductivity when it is added into the Ag pastes by providing more electrical conduction paths between Ag particles. This can be explained by the fact that capillary force of the melts of Bi58Sn42 can contribute to the rearrangement of the Ag particles during the heat-treatment inducing better connectivity between the Ag particles.

• Korean Journal of Food Science and Technology
• /
• v.22 no.1
• /
• pp.88-93
• /
• 1990

For effective separation of the N-TFA n-butyl ester amino acids on the stainless steel column by GLC, dual column of the mixed stationary phases, 3.36% OV-17+3.0% SE-30(column 1) and 1% NPGS +0.5% OV-17+0.5% SE-30(column 2) on chromosorb W HP 100-120 mesh, were used. On the column 1. the nineteen amino acids except histidine were obtained. However, alanine and valine peaks were not separated by this column. On the column 2, the sixteen amino acid peaks showed good separation, but tryptophan. arginine, histidine, and tyrosine peaks were not obtained. Calibration graphs for all amino acids obtained by the plotting the ratios of their peaks hights to that of internal standard versus the micro mole of the amino acids in the range $1.25{\times}10^{-3}{\mu}mol-1.0{\times}10^{-2}{\mu}mole$ showed linearity and passed through the origin.

• Horticultural Science & Technology
• /
• v.28 no.3
• /
• pp.507-514
• /
• 2010

This study was performed to reduce unpleasant taste and flavor of $Gastrodia$ $elata$ Blume as well as to improve utilization as functional food materials using fermentation. The component, antioxidant activity, and taste test were compared between fresh and fermented $Gastrodia$ $elata$ Blume powder (FGP). FGP contained higher level of total fat, protein, mineral, and fiber than raw material. The pH of FGP was higher compared to raw $Gastrodia$ $elata$ Blume powder (RGP), and antioxidant activity was as high as vitamin C regardless material status (raw vs. fermented). This result indicated that its activity was not decreased by fermentation. Dispersiveness and solubility of $Gastrodia$ $elata$ Blume powder was the best in 60-70 mesh. For sensory evaluation, FGP or RGP was mixed with either orange juice or yoghurt. The results showed that overall preference, taste, flavor, texture, and color were better in fermented $Gastrodia$ $elata$ Blume drinks than in raw ones. It is plausible that unpleasant taste and flavor of $Gastrodia$ $elata$ Blume was declined by fermentation. Thus, fermentation can be easily applied to eliminate unpleasant smell in $Gastrodia$ $elata$ Blume, and FGP can be mixed with other beverages to produce healthy food and drinks.

• Journal of the Korea Computer Graphics Society
• /
• v.23 no.4
• /
• pp.11-19
• /
• 2017

We propose a new pipeline of fluid surface reconstruction that incorporates hybrid SDF(signed distance fields) and adaptive fluid surface techniques to finely reconstruct liquid-solid mixed surfaces. Previous particle-based fluid simulation suffer from a noisy surface problem when the particles are distributed irregularly. If a smoothing scheme is applied to reduce the problem, sharp and detailed features can be lost by over-smoothing artifacts. Our method constructs a hybrid SDF by combining signed distance values from the solid and liquid parts of the object. We also proposed a method of adaptively reconstructing the surface of the fluid to further improve the overall efficiency. This not only shows the detailed surface of the solid and liquid parts, but also the detail of the solid surface and the smooth fluid surface when both materials are mixed. We introduce the concept of guiding shape and propose a method to get signed distance value quickly. In addition, the hybrid SDF and mesh reconstruction techniques are integrated in the adaptive framework. As a result, our method improves the overall efficiency of the pipeline to restore fluid surfaces.

• Structural Engineering and Mechanics
• /
• v.47 no.5
• /
• pp.599-622
• /
• 2013

Seismic response of two dimensional liquid tanks is numerically simulated using fully nonlinear velocity potential theory. Galerkin-weighted-residual based finite element method is used for solving the governing Laplace equation with fully nonlinear free surface boundary conditions and also for velocity recovery. Based on mixed Eulerian-Lagrangian (MEL) method, fourth order explicit Runge-Kutta scheme is used for time integration of free surface boundary conditions. A cubic-spline fitted regridding technique is used at every time step to eliminate possible numerical instabilities on account of Lagrangian node induced mesh distortion. An artificial surface damping term is used which mimics the viscosity induced damping and brings in numerical stability. Four earthquake motions have been suitably selected to study the effect of frequency content on the dynamic response of tank-liquid system. The nonlinear seismic response vis-a-vis linear response of rectangular liquid tank has been studied. The impulsive and convective components of hydrodynamic forces, e.g., base shear, overturning base moment and pressure distribution on tank-wall are quantified. It is observed that the convective response of tank-liquid system is very much sensitive to the frequency content of the ground motion. Such sensitivity is more pronounced in shallow tanks.

• Computers and Concrete
• /
• v.12 no.5
• /
• pp.585-612
• /
• 2013

The paper presents quasi-static numerical simulations of the behaviour of short reinforced concrete beams without shear reinforcement under mixed shear-tension failure using the FEM and four various constitutive continuum models for concrete. First, an isotropic elasto-plastic model with a Drucker-Prager criterion defined in compression and with a Rankine criterion defined in tension was used. Next, an anisotropic smeared crack and isotropic damage model were applied. Finally, an elasto-plastic-damage model was used. To ensure mesh-independent FE results, to describe strain localization in concrete and to capture a deterministic size effect, all models were enhanced in a softening regime by a characteristic length of micro-structure by means of a non-local theory. Bond-slip between concrete and reinforcement was considered. The numerical results were directly compared with the corresponding laboratory tests performed by Walraven and Lehwalter (1994). The advantages and disadvantages of enhanced models to model the reinforced concrete behaviour were outlined.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.26 no.9
• /
• pp.1209-1217
• /
• 2002

The use of a two dimensional hierarchical elements are investigated for the incompressible flow computation. The construction of hierarchical elements are explained by both a geometric configuration and a determination of degrees of freedom. Also a systematic treatment of essential boundary values has been developed for the degrees of freedom corresponding to higher order terms. The numerical study for the poisson problem shows that the computation with hierarchical higher order elements can increase the convergence rate and accuracy of finite element solutions in more efficient manner than the use of standard first order element. for Stokes and Cavity flow cases, a mixed version of penalty function approach has been introduced in connection with the hierarchical elements. Solutions from hierarchical elements showed better resolutions with consistent trends in both mesh shapes and the order of elements.

• Structural Engineering and Mechanics
• /
• v.61 no.3
• /
• pp.371-379
• /
• 2017

Modelling of a crack propagating through a finite element mesh under mixed mode conditions is of prime importance in fracture mechanics. In this paper, two crack growth criteria and the respective crack paths prediction in functionally graded materials (FGM) are compared. The maximum tangential stress criterion (${\sigma}_{\theta}-criterion$) and the minimum strain energy density criterion (S-criterion) are investigated using advanced finite element technique. Using Ansys Parametric Design Language (APDL), the variation continues in the material properties are incorporated into the model by specifying the material parameters at the centroid of each finite element. In this paper, the displacement extrapolation technique (DET) proposed for homogeneous materials is modified and investigated, to obtain the stress intensity factors (SIFs) at crack-tip in FGMs. Several examples are modeled to evaluate the accuracy and effectiveness of the combined procedure. The effect of the defects on the crack propagation in FGMs was highlighted.

• Journal of Fisheries and Marine Sciences Education
• /
• v.27 no.5
• /
• pp.1352-1363
• /
• 2015

This study was carried out to investigate the characteristics of the dependent variables depending on the condition changes of independent variable of the operation and the material during the production of collets added with rice and dried shrimp by using single extruder to utilize as basic data for the manufacture of extrusion collets. A total of 7 independent variables were set up as a raw, 20, 40 and 60 mesh for the powder particle size of rice; 12, 14, 16 and 18% for the moisture content of rice; 2, 4, 6 and 8% for the addition amount of dried shrimp; 90, 95, 100 and $110^{\circ}C$ for the barrel temperature; 210, 280 and 340 rpm for the screw speed; 4, 6, 8 and 10 mm for the discharge port diameter; 30, 40, 50 and 60 kg/h for the input amount of the mixed material. The characteristics of the dependent variables including puffing ratio, moisture content, lightness, uniformity, productivity of collets was to be studied by changing the conditions of the independent variables. As a results of this study, 20 mesh of powder particle size of rice, 14% of moisture content of rice, 4% of addition amount of dried shrimp, $100^{\circ}C$ of barrel temperature, 280 rpm of screw speed, 6 mm of discharge port diameter and 50 kg/h of input amount of mixed material were found to be the most preferable over other independent variables for the production of extrusion collets. In conclusion, it is necessary to set the independent variable in order to produce the high quality collets added with the rice as the main raw material and dried shrimp as the sub-materials.