• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.7
• /
• pp.796-808
• /
• 2007

In this paper, two novel compact microstrip bandstop filters using complimentary split ring resonators(CSRRs) and spiral resonators is proposed. The first one is the bandstop filter using an array of CSRRs etched on the center line of a microstrip. The bandstop is due to the presence of negative effective permittivity and positive permeability near resonant frequency which prevent the wave propagation. The second on is the bandstop filter using an array of spiral resonators etched on the center line of a microstrip. The bandstop is due to the self-resonance of spiral circuit. We have achieved controllable resonance frequency and bandwidth, super compact dimension, low insertion losses in the passband and high level of rejection in the stopband with sharp cutoff. The electrical sizes of two proposed filter are very small. Additionally, they can be easily fabricated and compatible with MMIC or PCB technology.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.11 no.4
• /
• pp.1-8
• /
• 2011

In this paper, a microstrip bandpass filter(BPF) with 3 dB bandwidth of more than 50 % at center frequency of 30 GHz was implemented. The implemented BPF is to be used as ASK(Amplitude Shift Keying) transmission and reception filters in IF band for THz transmitter and receiver capable of 10 Gb/s wireless data transmission. The microstrip BPF with ultra-wideband characteristics was implemented using a stepped-impedance lowpass filter(LPF) and a composite quarter-wave short stubs where the LPF is functioning as attenuating the upper stopband and quarter-wave short stubs is functioning as attenuating the lower stopband. The measured results are as follows; the insertion loss is 0.65 dB at 30 GHz, the stopband characteristics are -10 dB and -16 dB at 10 GHz and 50 GHz, respectively, and the passband flatness is ${\pm}0.5$ dB at 20~40 GHz.

• The Journal of the Acoustical Society of Korea
• /
• v.13 no.1E
• /
• pp.5-10
• /
• 1994

It is obtained the general expessions of the numerical method are applied for the TEM-mode analysis of multu-layer multi-coupled microstrip lines, In this paper, coupled microstrip are replaced by three-coupled microstrip lines in special aplications. Three-layer versions of three-coupled microstrip lines are specially attactive because of the additional flexibilities offered by three-layer configuration. This structure can be used for obtaining large capacitance and preventing coupling among microstrip lines in filter and coupler. Sappihre is chosen for anisotropic substrates material. The permittivity parallel to the optical axis is higher than the permittivity in the plane perpendicular to this axis.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.1
• /
• pp.20-26
• /
• 2003

This paper presents hairpin-comb bandpass filter using ground aperture. Hairpin-comb resonator maintains the weak coupling though the space between two resonators is very small. This has the good merit that the entire filter size is small for narrowband bandpass filter. The coupling between two hairpin-comb resonators so very weak that can't be applicable to general microstrip. We compensate the coupling by using ground aperture. It makes the hairpin-comb filter possible that can be applicable to general microstrip. Also it has the good merit which adjusts the bandwidth by changing the size of aperture without changing the space. In this paper, we fabricate the bandpass filter, which has 1.78 GHz center frequency and 62 MHz (3.5%) fractional bandwidth.

• Proceedings of the Korean Institute of Communication Sciences Conference
• /
• 2004.07a
• /
• pp.320-320
• /
• 2004

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.3A
• /
• pp.430-434
• /
• 2000

In this paper, a novel photonic bandgap(PBG) structure is proposed for increasing stropband of lowpass filter without the size increment of circuit for application in microstrip circuits. The proposed structure is connected in parallel two periodic structures which have different center frequency of the stopband. The wide stopband is achieved by two periodic structures of two different stopbands. We also show the performance improvement of microstrip patch antenna by etching of the proposed structure in ground plane.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.24 no.5
• /
• pp.747-752
• /
• 1987

Analysis and design procedures for both symmetrical and non-symmetrical open-circuited interdigital multiple coupled microstrip line structures for applications as wide-band DC blocks/filters have been presented. The design equations, as is the case of other microstrip structures, are based on a simplified TEM model. The experimental results are in good agreement with the theoretically predicted ones.

• Journal of Navigation and Port Research
• /
• v.30 no.5 s.111
• /
• pp.331-334
• /
• 2006

In this paper, we designed and fabricated the lowpass filter with the wide stopband characteristics using microp- strip line. Adding the $\lambda_g/4$ open stub at the input and output ports, we developed the L-C ladder type lowpass filter using the open stub which has wide stopband characteristics. In order to reduce the entire size qf this filter, the high impedance microstrip lines were made with the meander structure. The lowpass filter was fabricated with the cutoff frequency 2.3 GHz and its measured frequency responses agree well with the simulation results.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.7
• /
• pp.644-652
• /
• 2004

In this paper, we designed a cascaded microstrip lowpass filter using the lowpass filters previously proposed. The previously proposed lowpass filters have a ultra-wide stopband and prominent cutoff sharpness using the combined characteristics of slot and microstrip open stub, respectively, and they are catagorized into 2 types by the method that determining their passband characteristics. The first type is determined its passband characteristics by open stub characteristics and the second is by slot characteristics. By cascading these structures with impedance adjustment of each element, the deeper out-of-band rejection and the sharper skirt response were achieved. The fabricated cascaded lowpass filters have -3㏈ cutoff frequencies at 1.035㎓ and 1.286㎓ respectively and -20㏈ stopband is over 20㎓ for both structures.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.9
• /
• pp.924-930
• /
• 2003

In this paper, a novel miniaturized microstrip duplexer with attenuation pole is proposed. A three-pole microstrip CT(Cascade Trisection) two bandpass filters have each asymmetrically prescribed transmission zero are design and fabrication. This CT bandpass filter changes coupling structure, which not only shifts the location of attenuation poles but also improves skirt characteristics. The duplexer results of measurement with the cross coupling CT bandpass filters has been yielded better isolation and sharper skirt behavior than that with a conventional bandpass filter. The results of measurement are almost similar to those of simulation results.