• Spatial Information Research
• /
• 제14권1호
• /
• pp.129-150
• /
• 2006

본 연구에서는 GIS 및 확률 기법을 이용하여 광상의 위치와 지질, 지화학 및 지구물리 자료들 간의 상관관계를 분석하고, 광상부존가능도(Mineral potential map) 작성 및 검증을 수행하였다. 연구지역은 1:25만 강릉도폭지역 a이며, 구축된 데이터베이스 자료는 1:25만 광상분포도, 지화학도, 지질도, 부우게 중력이상도, 자력이상도이다. 본 연구에 사용된 광상은 퇴적기원의 비금속광상(고령토, 도석, 규석, 운모, 연옥, 석회석, 납석)이다. 원소별 지화학도 작성은 채취된 각 시료 3,595개의 원소별 분석치를 이용하여 IDW 보간법으로 만들었다. 구축된 지화학도는 Al, Alkalinity, As, Ba, Ca, Cd, Co, Cr, Cu, Fe, K, Li, Mg, Mn, Mo, Na, Ni, Pb, Si, Sr, V, W, Zn, $Cl^-,\;F^-,\;{NO_2}^-,\;{NO_3}^-,\;{PO_4}^{3-},\;{SO_4}^{2-}$, pH, Eh 및 Conductivity로 총 32개이다. 이러한 광상과 관련 요인들 간의 상관관계는 확률기법인 weight of evidence를 적용하여 계산하였고, 이를 바탕으로 광상부존가능도를 작성하였다. 광상부존가능도는 wieght of evidence의 W+와 W- 값을 GIS 중첩분석에 적용하여 작성하였다. 계산된 광상부존가능지수는 기존 광상부존가능성을 정량적으로 설명하고 표현하며 검증할 수 있는 값이다. 각 기법을 이용하여 작성한 광상부존가능도의 검증결과는 85.66%의 정확도를 나타내었다.

• 한국재료학회지
• /
• 제14권3호
• /
• pp.218-223
• /
• 2004

P-type $\beta$-FeSi$_2$ with a nominal composition of $Fe_{0.92}Mn_{0.08}Si_2$ powders has been produced by mechanical alloying process. As-milled powders were spray dried and consolidated by atmospheric plasma thermal spraying as a rapid sintering process. As-milled powders were of metastable state and fully transformed to $\beta$-$FeSi_2$ phase by subsequent isothermal annealing. However, as-thermal sprayed $Fe_{0.92}Mn_{0.08}Si_2$ consisted of untransformed mixture of $\alpha$-$Fe_2Si_{5}$ and $\varepsilon$-FeSi phases. Isothermal annealing has been carried out to induce transformation to the thermoelectric semiconducting $\beta$-$FeSi_2$ phase. Isothermal annealing at $845^{\circ}C$ in vacuum gradually led to the thermoelectric semiconducting $\beta$-$FeSi_2$ phase transformation, but some residual metallic $\alpha$ and $\varepsilon$ phases were unavoidable even after prolonged annealing. Thermoelectric properties of $\beta$-$FeSi_2$ materials before and after isothermal annealing were evaluated. Seebeck coefficient increased and electric conductivity decreased with increasing annealing time due to the phase transition from metallic phases to semiconducting phases. Thermoelectric properties showed gradual increment, but overall properties appeared to be inferior to those of vacuum hot pressed specimens.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2010년도 춘계학술발표대회
• /
• pp.19.2-19.2
• /
• 2010

Printed electronics using printing process has broadened in all respects such as electrics (lighting, batteries, solar cells etc) as well as electronics (OLED, LCD, E-paper, transistor etc). Copper is considered to be a promising alternative to silver for printed electronics, due to very high conductivity at a low price. However, Copper is easily oxidized, and its oxide is non-conductive. This is the highest hurdle for making copper inks, since the heat and humidity that occurs during ink making and printing simply accelerates the oxidation process. A variety of chemical treatments including organic capping agents and metallic coating have been used to slow this oxidation. We have established synthetic conditions of copper nanoparticles (CuNPs) which are resistant to oxidation and average diameter of 20 to 50nm. Specific resistivity should be less than $4\;{\mu}{\Omega}{\cdot}cm$ when sintered at lower temperature than $250^{\circ}C$ to be able to apply to conductive patterns of FPCBs using ink-jet printing. Through this study, the parameters to control average diameter of CuNPs were found to be the introduction of additive agent, the feeding rate of reducing agent, and reaction temperature. The CuNPs with various average diameters (58, 40, 26, 20nm) could be synthesized by controlling these parameters. The dispersed solution of CuNPs with an average size of 20 nm was made with nonpolar solvent containing 3 wt% of binder, and then coated onto glass substrate. After sintering the coated substrates at $250^{\circ}C$ for 30 minutes in nitrogen atmosphere, metallic copper film resulted in a specific resistivity of $4.2\;{\mu}{\Omega}{\cdot}cm$.

• 한국재료학회지
• /
• 제19권4호
• /
• pp.186-191
• /
• 2009

Thermoelectric power and resistivity are measured for the perovskite $LaNi_{1-x}Ti_xO_3$ ($x{\leq}0.5$) in the temperature range 77 K - 300 K. The measured thermoelectric power of $LaNi_{1-x}Ti_xO_3$ ($x{\leq}0.5$) increases linearly with temperature and is represented by A + BT. The x = 0.1 sample showed metallic behavior, the x = 0.3 showed metal and insulating transition around 150 K, and x = 0.5 showed insulating behavior the over the whole temperature range. The electrical resistivity of x = 0.1 shows linear temperature dependence over the whole temperature range and $T^2$ dependence. On the other hand, the electrical resistivity of x = 0.3 shows a linear relation between $ln{\rho}$ and $T^{-1/4}$ (variable range hopping mechanism) in the range of 77 K to 150 K. For x = 0.5, the temperature dependence of resistivity is characteristic of insulating materials; the resistivity data was fitted to an exponential law, such as ln(${\rho}/T$) and $T^{-1}$, which is usually attributed to a small polaron hopping mechanism. These experimental results are interpreted in terms of the spin polaron (x = 0.1) and variable range hopping (x = 0.3) or small polaron hopping (x = 0.5) of an almost localized $Ni^{3+}$ 3d polaron.

• Applied Microscopy
• /
• 제45권4호
• /
• pp.236-241
• /
• 2015

Carbon-coated Ni, Cu and Sn nanocapsules were investigated by means of X-ray diffraction (XRD), transmission electron microscopy (TEM) and a four-point probe device. All of these nanocapsules were prepared by an arc-discharge method, in which the bulk metals were evaporated under methane ($CH_4$) atmosphere. Three pure metals (Ni, Cu, Sn) were typically diverse in formation of the carbon encapsulated nanoparticles and their different mechanisms were investigated. It was indicated that a thick carbon layers formed on the surface of Ni(C) nanocapsules, whereas a thin shell of carbon with 1~2 layers covered on Cu(C) nanocapsules, and the Sn(C) nanocapsules was, in fact, a longger multi-walled carbon nanotubes partially-filled with metal Sn. As one typical magnetic/dielectric nanocomposite particles, Ni(C) nanocapsules and its counterpart of oxide-coated Ni(O) nanocapsules were compared in the electrically conductive behaviors for further applications as the electromagnetic materials.

• 한국재료학회지
• /
• 제18권7호
• /
• pp.384-388
• /
• 2008

Hydrogen production via high high-temperature steam electrolysis consumes less electrical energy than compared to conventional low low-temperature water electrolysis, mainly due to the improved thermodynamics and kinetics at elevated temperaturetemperatures. The elementalElemental powders of Cu, Ni, and YSZ are were used to synthesize high high-temperature electrolysis cathodecathodes, of Ni/YSZ and Cu/YSZ composites, by mechanical alloying. The metallic particles of the composites were uniformly covered with finer YSZ particles. Sub-micron sized pores are were homogeneously dispersed in the Ni/YSZ and Cu/YSZ composites. In this study, The cathode materials were synthesized and their Characterizations properties were evaluated in this study: It was found that the better electric conductivity of the Cu/YSZ composite was measured improved compared tothan that of the Ni/YSZ composite. Slight A slight increase in the resistance can be produced for in a Cu/YSZ cathode by oxidation, but it this is compensated offset for by a favorable thermal expansion coefficient. Therefore, Cu/YSZ cermet can be adequately used as a suitable cathode material of in high high-temperature electrolysis.

• 한국광학회지
• /
• 제19권5호
• /
• pp.381-385
• /
• 2008

InGaN/Sapphire LED에서 기판 제거와 패키지 방식이 광출력 특성에 미치는 영향을 분석하였다. Sapphire 기판의 제거는 반도체 접합에서 발생된 열의 방출에 도움이 되지만, 반대로 광추출효율이 손상되는 문제점이 수반된다. Sapphire 기판이 제거된 칩을 열전도율이 좋은 금속의 마운트 위에 부착하면, 최대 구동전류는 현저히 증가하고 광출력도 상당히 증가됨으로써, 광추출효율이 손상되는 문제점이 어느 정도 보상된다. 하지만, sapphire 기판이 제거된 칩을 상대적으로 열전도율이 낮은 유전체의 마운트 위에 부착하는 경우에는, 거의 모든 입력전류 범위에서 sapphire 기판이 남아 있는 일반형 칩보다 낮은 광출력을 나타낸다. 따라서, 작은 광출력이 요구되는 응용분야에서는 사용된 칩 마운트의 종류에 무관하게, 일반형 칩이 sapphire 기판이 제거된 칩 보다 유리한 것으로 분석된다.

• 한국기계가공학회지
• /
• 제18권7호
• /
• pp.97-103
• /
• 2019

Mn+1AXn (MAX) phases are a family of nano-laminated compounds that possess unique combination of typical ceramic properties and typical metallic properties. As a member of MAX-phase, $Ti_2AlN$ bulk materials are attractive for some high temperature applications. In this study, $Ti_2AlN$ bulk with high density were synthesized by spark plasma sintering method. X-ray diffraction, micro-hardness, electrical and thermal conductivity were measured to compare the effect of material properties both $Ti_2AlN$ bulk samples and a conventional Ti-6Al-4V alloy. A femto-second laser conditions were conducted at a repetition rate of 6 kHz and laser intensity of 50 %, 70% and 90 %, respectively, laser confocal microscope were used to evaluate the width and depth of ablation. Consequently, the laser ablation result of the $Ti_2AlN$ sample than that of the Ti-6Al-4V alloys show a considerably good ablation characteristics due to its higher thermal conductivity regardless of to high densification and high hardness.

• 마이크로전자및패키징학회지
• /
• 제24권4호
• /
• pp.39-46
• /
• 2017

본 연구는 평판형 히터용 금속방열판상의 세라믹 절연층 제조, 즉 절연성 금속기판에 관한 것이다. 반도체나 디스플레이의 열처리 공정 등에 사용되는 평판형 히터를 제조함에 있어서, 온도 균일도를 높이기 위해 금속 방열판으로서 열전도율이 높고, 비교적 가벼우며, 가공성 좋은 알루미늄 합금 기판이 선호된다. 이 알루미늄 기판에 발열 회로 패턴을 형성하기 위해서는 금속 기판에 절연층으로서 고온 안정성이 우수한 세라믹 유전체막을 코팅하여야 한다. 금속 기판상에 세라믹 절연층을 형성함에 있어서 가장 빈번히 발생하는 첫 번째 문제는 금속과 세라믹의 이종재료 간의 큰 열팽창계수 차이와 약한 결합력에 의한 층간박리 및 균열발생이다. 두 번째 문제는 절연층의 소재 및 구조적 결함에 따른 절연파괴이다. 본 연구에서는 이러한 문제점 해소를 위해 금속소재 기판과 세라믹 절연층 사이에 완충층을 도입하여 이들 간의 기계적 매칭과 접합력 개선을 도모하였고, 다중코팅 방법을 적용하여 절연막의 품질과 내전압 특성을 개선하고자 하였다.

• 방사성폐기물학회지
• /
• 제2권2호
• /
• pp.125-133
• /
• 2004

최대 선출력 61 ㎾/m 및 평균 연소도 1,770 ㎿d/tU의 조건으로 하나로에서 조사한 DUPIC(Direct Use of Spent PWR Fuel in CANDU Reactors) 핵 연료를 EPMA (Electron Probe Micro Analyzer)를 이용하여 핵분열 생성물을 분석하였다. EPMA의 정확한 분석 방법을 확립하고자, 핵분열생성물 대신 시약을 첨가하여 제조한 모의 DUPIC 핵연료로 EPMA 분석을 수행하였고, 그 결과를 습식 화학 분석의 결과와도 비교하여 평가하였다. 모의 DUPIC 핵연료 중심부의 금속 석출물은 약 1 $\mu\textrm{m}$ 정도의 크기로 관찰되었으며, 이들의 조성은 Mo-53.89 at.%, Ru-37.40 at.% 및 Pd+Rh-8.71 at%이었다. 모의 DUPIC 핵연료 시험에서 정립한 시험방법으로 조사한 DUPIC 핵연료 시편의 금속 석출물 특성을 분석하였다. 핵연료 중앙부에서 관찰된 금속 석출물들의 크기는 2∼2.5 $\mu\textrm{m}$ 정도이었으며, Mo-47.34 at.%, Ru-46 at.%, Pd+Rh-6.65 at.%의 조성임을 확인하였다. 이 실험을 위하여, 특별히 시료의 전도성을 향상시키기 위한 처리를 하였으며, 작은 금속 석출물에 EPMA의 전자빔을 정확히 조사할 수 있는 실험 조건을 제시하였다.