• 한국해양학회지
• /
• v.13 no.1
• /
• pp.19-28
• /
• 1978

To estimate the chemical mass balance of several kinds of trace metals in sea water, suspended matter and bottom sediments, sixty samples from the Kum and Mankyung estuaries were analyzed. In both estuaries, the distribution patterns of leachabl suspended trace metals and of bottom sediments were established to be similar. The relationship between the metal concentration and clay content of the sediments was found to be such that the metal concentration increases with an increase in clay content. A linear correlation ws determined between pairs of leachable metals (Fe-Zn, Fe-Mn and Zn-Mn) in the Kum estuary. However, in the Mankyung estuary linear relationship does not exist. Finally, it is suggested that the trace metals are reworking in the Kum estuary and those in the Mankyung estuary are sinking.

• Journal of Energy Engineering
• /
• v.2 no.1
• /
• pp.68-74
• /
• 1993

In order to maximize the utility of vacuum residue, supercritical solvent extraction technique where n-pentane was used as a supercritical solvent was applied to obtain deasphalted oil from vacuum residue. Oil-extraction yield at various temperatures and pressures and the contents of metal complex and sulfur of extracted oil were investigated. In supercritical state, extraction yield of deasphalted oil was found to be strongly dependent on the n-pentane density, and the metal complex content of extracted oil was effectively lowered when compared with that of vacuum residue. However, the sulfur content of extracted oil showed little difference when compared with that of vacuum residue.

• Bulletin of the Korean Chemical Society
• /
• v.35 no.2
• /
• pp.597-600
• /
• 2014

In this work, the electromagnetic interference shielding effectiveness (EMI-SE) of carbon nanotube/carbon fiber-reinforced HDPE matrix composites are investigated with various preparation conditions, such as the carbon fiber and carbon nanotube content, the presence of metal additives, as well as mixing speed and time. It was found that the EMI-SE of the composites increased with filler contents and metal additives. These results indicate that the content and length of carbonaceous fillers determine the electric networks in the composites, resulting in the control of the EMI-SE of the composites.

• Journal of the Semiconductor & Display Technology
• /
• v.13 no.3
• /
• pp.13-19
• /
• 2014

Phosphoric acid was used as etching agent instead of conventional peroxide - based chemicals for forming pattern of ultra definition display. Etchant was synthesized by mixing etching agent, oxidation agent, buffer solution, and additive into solvent, deionized water. Thicknesses of copper, main metal of ultra definition display, for etching, were 10,000 and $30,000{{\AA}}$. Etch stop of good low skew for proper pattern formation has been occurred at the content ratio of phosphoric acid 60 - 64%, nitric acid 4 - 5%, additive(potassium acetate) 1 - 3%. Buffer solution(acetic acid) decreased the metal contact angle $63.07^{\circ}$ to $42.49^{\circ}$ for benefiting pattern formation. Content variations on four components (phosphoric acid, nitric acid, acetic acid, potassium acetic acid) of the etchant with storage time were within 3 wt% after 24 hrs of etching work.

• Journal of the Korean Geotechnical Society
• /
• v.21 no.5
• /
• pp.231-241
• /
• 2005

Laboratory experiments were performed to examine the effects of water content and to see if permittivity had sufficient sensitivity to identify subsurface contamination. Both real and imaginary permittivities of unsaturated sand were strongly governed by the volumetric water content. Especially, a linear relationship between real permittivity and volumetric water content was derived at high frequencies (MHz ranges). Heavy metals in pore fluid result in significant increases in the effective imaginary permittivity, due to ionic conduction, but decreases in the real permittivity arises due to the decreased orientational polarization of water molecules caused by hydration of ions. Clear increase in the effective imaginary permittivity with heavy metal concentration was found to be valuable in the application of electrical methods for detecting heavy metals in the subsurface. However, because the permittivity is primarily dependent on the volumetric water content of soil, pre-evaluation on the volumetric water content is required.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.10 no.1
• /
• pp.32-44
• /
• 2000

The practice of welding stainless steel is known to produce various valance states of chromium. $CO_2$ flux cored arc welding on stainless was performed in fume collection chamber. Content of total chromium and hexavalent chromium in fumes, content of hexavalent chromium in total chromium, solubility of hexavalent chromium were investigated. Content of total chromium in fumes increases from 2~3% to 7~9% as a function of input energy, but hexavalent chromium, less than 1.2% in fumes, is not related to input energy. Hexavalent chromium in fumes exists as solubles up to 90%. Content of total chromium in flux cored arc welding fumes and solubility of hexavalent chromium are similar to shielded metal arc welding fumes, but content of hexavalent chromium is similar to metal inert gas welding fumes. These characteristics are relevant to flux of wires and $CO_2$ shielding gas.

• Tribology and Lubricants
• /
• v.13 no.2
• /
• pp.96-104
• /
• 1997

This paper was focused on the wear characteristics of ion-nitrided metal and with ion-nitride processing, which is basically concerned with the effects of carbon content in workpiece and added carbon content gas atmosphere on the best wear performance. Increased carbon content in workpiece increases compound layer thickness, but decreases diffusion layer thickness. On the other hand, a small optimal amount of carbon content in gas atmosphere increase compound layer thickness as well as diffusion layer thickness and hardness. Wear tests show that the compound layer of ion-nitrided metal reduces wear rate when the applied wear load is small. However, as the load becomes large, the existence of compound layer tends to increase wear rate. Compressive residual stress at the compound layer is the largest at the compound layer, and decreases as the depth from the surface increases. It is found in the analysis that under small applied load, the critical depth where voids and cracks may be created and propagated is located at the compound layer, so that the adhesive wear is created and the existence of compound layer reduces the amount of wear. When the load becomes large, the critical depth is located below the compound layer and delamination, which may explained by surface deformation, crack nucleation and propagation, is created and the existence of compound layer increases wear rate. For the compound layer, at added carbon contents of 0 percent and 0.5 at. percent, the $\varepsilon$ monophase is predominant. But at 0.7 at. percent added carbon, the $\varepsilon$ monophase formation tends to be severely inhibited and r' and $Fe_3C$ polyphase formation becomes dominant. This increased hard $\varepsilon$ phase layer was observed to be more beneficial in reducing friction and wear.

• Economic and Environmental Geology
• /
• v.30 no.2
• /
• pp.123-135
• /
• 1997

In order to investigate the dispersion patterns and contamination level of heavy metals in the soil-ecosystem and to evaluate the efficiency of soil remediation by reversed soil method, soils and plants were collected from the Dongjin Au-Ag-Cu mine area and analysed for heavy metals. The dispersion patterns of heavy metals in soils and plants show that heavy metal pollutions caused by waste rump around Dongjin mine are mainly found in the vicinity of the waste rump and in the southward slanting of mine. Toxic metallic pollutants from the mine influence heavy metal contents in paddy soils in downstream area, and may be a potential sources of heavy metal pollution on crop plants. Soil samples collected from the remediated rice farming field by reversed method show similar levels of heavy metal content to those from the polluted rice farming field, but topsoil enrichment of heavy metals are not found. Heavy metal contents of the rice plants collected from remediated rice farming field are significantly lower than those from polluted rice farming field, and it suggests that the reversed soil method is effective for the reduction of bioavailability of heavy metals.

• Journal of the Korean Ceramic Society
• /
• v.31 no.3
• /
• pp.321-329
• /
• 1994

Functionally gradient materials(FGM), which have the continuous or stepwise variation in a composition and microstructure, are being noticed as the material that solves problems caused by heterogeneous interface of coating or joining. And these materials also expect new functions occured by gradient composition itself. Therefore, to examine possibility of thermal barrier materials, TZP/Mo·FGM and TZP/Ni·FGM were fabricated by sintering method. As to the sintered specimens, sintering shrinkage, relative density and Vicker's hardness in each composition were examined. The phenomena due to the difference of sintering shrinkage velocity during sintering process and the thermal stress induced through differences of thermal expansion coefficient in FGM were discussed. And the structure changes at interface and microsturcture of FGM were investigated. As a results, the difference of shrinkage between ceramic and metal was about 14% in TZP/Mo and 7% in TZP/Ni. The relative density and hardness were considerably influenced by metal content changes. Owing to unbalance of sintering shrinkage velocity between ceramic and metal, various sintering defects were occured. To control these sintering defects and thermal stress, gradient composition of FGM should be narrow. The microstructure changes of FGM depended on the ceramic or metal volume percents and were analogous to the theoretical design.

• Journal of the Korean institute of surface engineering
• /
• v.52 no.6
• /
• pp.334-341
• /
• 2019

Organometal halide perovskite materials have attracted much attention in the photovoltaic and light emitting devices due to the compositional flexibility with AMX₃ formula (A is an organic amine cation; M is a metal ion; X is a halogen atom). The addition of homovalent or heterovalent metal cations to the bulk organohalide perovskites has been performed to modify their energy band structure and the relevant optoelectronic properties by ligand-assisted ball milling. Here, we report CH₃NH₃Pb_1-xM_xBr₃ nanocrystals substituted by metallic cations (M is Sn²⁺, In³⁺, Bi³⁺; x = 0, 0.01, 0.02, 0.05, 0.1, 0.2). Photoluminescence and quantum yield was significantly reduced with increasing metallic cations content. These quenching effect could be resulted from the metal cations that behave as a non-radiative recombination center.