• 전기학회논문지
• /
• 제57권7호
• /
• pp.1187-1194
• /
• 2008

This paper presents a high-power electronic ballast for a metal-hallide lamp(MHL) that employs frequency modulation(FM) technique to eliminate acoustic resonance(AR). The proposed ballast consists of a full-bridge rectifier, a power factor correction(PFC) circuit, a full-bridge(FB) inverter, an ignitor using LC resonance and an FM control circuit. Whereas a manual PFC provides advantages in terms of high reliability and low cost for constructing the circuit, it is difficult to supply a stable voltage because of the output voltage ripple that occurs with a period of 120Hz. Although the ballast can be designed with a small size and a light weight if it is driven at a switching frequency between 1 and 100 kHz, AR will occur if the eigen-value frequency of the lamp coincides with the inverter's operation frequency. The operation frequency was modulated in real time according to the output voltage ripple to compensate for the variation in power supplied to the lamp and eliminate AR. Performance of the proposed technique was validated through numerical analysis, computer simulation using PSPICE and by applying it to an electronic ballast for a prototype 1kW MHL.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2002년도 춘계종합학술대회
• /
• pp.301-304
• /
• 2002

본 논문은 70［W］급 세라믹 방전관 메탈할라이드 램프용 전자식 안정기의 설계와 제자에 대하여 기술하였다. 제안한 안정기는 정류기, 능동성 역률개선회로, 하프브리지 인버터, LC 공진회로 및 제어회로로 구성되며, 램프의 재점등에 필요한 타이머 기능을 추가하였다. 점등시 램프에는 음향공명현상과 플리커 현상을 피하기 위하여 45［KHz］의 고주파 전압이 인가되도록 설계하였다. 실험결과로부터 역률과 효율은 각각 91［%], 97.7［%］로 평가되었다.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2002년도 추계종합학술대회
• /
• pp.435-439
• /
• 2002

본 논문은 70[W]급 세라믹 방전관 메탈할라이드 램프용 전자식 안정기의 설계 및 제작에 대하여 기술하였다. 개발한 안정기는 정류회로, 능동성 역률개선회로, 하프브리지 인버터, LC 공진회로 및 제어회로로 구성되며, 램프의 재점등에 필요한 타이머 기능을 부가하였다. 점등시 램프에는 음향공명현상과 플리커 현상을 피하기 위하여 40[kHz]의 고주파 전압이 인가되도록 하였다. 실험결과로부터 역률과 효율은 각각 99.8[%], 93.1[%]로 평가되었다.

• 한국전자통신학회논문지
• /
• 제8권9호
• /
• pp.1307-1312
• /
• 2013

본 논문에서는 알칼리성 또는 산성을 띠는 특정 용액 내에서 전기분해 원리를 이용하여 금속 표면을 산화시켜 절연피막을 형성하는 장치를 개발한다. 기존에는 주로 양극에만 펄스 형태로 전압을 인가하는 단극성(unipolar) 방식이지만 본 논문에서는 H-브리지를 이용하여 양극에 양(+)전압과 음(-)전압을 번갈아 가면서 전압을 공급하는 양극성(bipolar) 장치를 제작하였으며, 금속 시편의 특성에 맞는 다양한 전기적인 조건을 가지고 산화피막을 형성할 수 있는 장치를 개발하였다. 공급전류 가변은 PWM 변조를 이용하였으며, (+)와 (-)의 극성변화는 H-브리지를 이용하여 양극성 펄스전압을 공급할 수 있도록 하였다. 그 결과로써 단극성보다 균일한 기공을 갖는 피막이 형성되었다.

• Corrosion Science and Technology
• /
• 제6권3호
• /
• pp.128-132
• /
• 2007

For a quantitative inspection on the performance of weathering steel bridges, we have investigated the relationship between the corrosion rate and the composition of the rust layers formed on weathering steel bridges located in various environments in Japan and applied a protective ability index (PAI) to the bridges. The corrosion rates were clearly classified by the PAI, ${\alpha}/{\gamma}*$ and sub index of $({\beta}+s)/{\gamma}*$, where $\alpha$, \gamma*, $\beta$ and s are the mass ratio of crystalline $\alpha-FeOOH$, the total of $\gamma$-FeOOH+ $\beta$-FeOOH + the spinel-type iron oxide (mainly $Fe_3O_4$), $\beta-FeOOH$ and spinel-type iron oxide, analyzed by powder X-ray diffraction, respectively. In the case of ${\alpha}/{\gamma}$*>1, the rust layer works protective enough to reduce the corrosion rate less than 0.01 mm/y. The sub index $({\beta}+s)/{\gamma}*$<0.5 or >0.5 classifies the corrosion rate of the non-protective rust layers, therefore the former state of the rust layer terms inactive and the latter terms active. The quantitative inspection of a weathering steel bridge requires a performance-inspection (PI) and periodical deteriorationinspections (DI). The PI can be completed by checking of the PAI, ${\alpha}/{\gamma}*$. The DI on the weathering steel bridges where deicing salt is sprinkled can be performed by checking the PAI, $({\beta}+s)/{\gamma}*$.

• 구강회복응용과학지
• /
• 제18권2호
• /
• pp.113-118
• /
• 2002

Long bridge가 필요한 구강암종환자에게 자기공명영상을 촬영하여야 하는 경우, fiber reinforced polymer ceramics로 잠정보철물을 제작해준 경우 충분한 파절 저항성과 심미성을 얻을 수 있었다. 하지만, 여기에 대한 장기간의 연구와 관찰이 필요하리라 사료된다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집
• /
• pp.18-21
• /
• 2002

As the mask design rules get smaller, the probability of the process failure becomes higher due to the narrow overlay margin between the contact and metal interconnect layers. To obtain the minimum process margin, a tabbing and cutting method is applied with the rule based optical proximity correction to the metal layer, so that the protection to bridge problems caused by the insufficient space margin between the metal layers can be accomplished. The side-lobe phenomenon from the attenuated phase shift mask with the tight design nile is analyzed through the aerial image simulation for test patterns with variation of the process parameters such as numerical aperture, transmission rate, and partial coherence. The corrected patterns are finally generated by the rules extracted from the side-lobe simulation.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2002년도 하계종합학술대회 논문집(2)
• /
• pp.209-212
• /
• 2002

As the mask design rules get smaller, the probability of the process failure becomes higher doc to the narrow overlay margin between the contact and metal interconnect layers. To obtain the minimum process margin, a tabbing and cutting method Is applied with the rule based optical\ulcorner proximity correction to the metal layer, so that the protection to bridge problems caused by the insufficient space margin between the metal layers can be accomplished. The side-lobe phenomenon from the attenuated phase shift mask with the tight design rule is analyzed through the aerial image simulation for test patterns with variation of the process parameters such as numerical aperture, transmission rate, and partial coherence. The corrected patterns are finally generated by the rules extracted from the side-lobe simulation.

• 대한치과보철학회지
• /
• 제27권2호
• /
• pp.53-78
• /
• 1989

This study was taken to observe the changes of the residual stress in the alloy and to measure 3 dimensional distortions of the long span ceramo-metal bridge. The materials used in this study were Pors-on 4 (Pd-Ag alloy), and Ceramco and Vita VMK 68 powders. The residual stress of the alloy was measured on the six specimens (dia. 8m/m) by the X-ray diffraction stress analyzer according to the kind of ceramic powder and different measuring stages. And, for the measurement of the distortions, fifteen specimens of the anterior 8-unit ceramo-metal brige were fabricated and subjected to the 3-D coordinate measuring machine. Variables included the 2 kinds of a ceramic powder and the presence or absence of a splint bar at the cast metal framework. The measuring stages in both were after casting, after degassing and after glazing. The following conclusions were obtained : 1. The residual stress of the alloy showed increasing tendency for the tension by the ceramic fusing, but there was not significance. 2. The tendency of the distortions in the cast metal frameworks were decrease of the width, the anterior displacement and sagging. 3. The amount of the distortions at the degassing stage were greater than that at the ceramic fusing stage. 4. The splint bar was effective to control the distortion only at ceramic fusing stage. 5. The sagging distortion in the Ceramco firing were even through all measuring stages, but in the Vita firing, pronounced at degassing stage.

• 건축역사연구
• /
• 제16권4호
• /
• pp.77-93
• /
• 2007

According to documentary records Woljeong-gyo(stone bridge) is built in 760(Silla the 35th King Gyeongdeok 19) and used as original function until 1280(Goryeo the 25th King Chungryeol 6) as Chunyang-gyo. But in those days "Donggyeongjapgi" was published in 1669(Joseon Hyeonjong 10) we assume that it was lost its original function. There are four pier in the type of a ship with the same distance in the middle of river. We can see it is the site of bridge as parts of stonework of bridge are remained. In 1975 the abutments and piers are surveyed and in 1984 stone investigation twice and excavation three times which were to plan restoration were done. Now the restoration of abutments both ends are worked. For restoration of Woljeong-gyo studied documentary records and excavation recoeds were collected and examined. It helped to see the bridge in southern China twice to restore the bridge. Unearthed articles such as yeonham(a kind of member to support roof tiles) and giwa(roof tile) gave decisive clues to assume upper structure of the bridge and from Chinese bridges are helped to type of the bridge. It is certain Woljeong-gyo was ranggyo which means that upper structure was made with wooden members and the stone piers shaped of a ship below and near the abutments both ends another buildings were. Youngjocheok(the architectural measure) of this bridge is similar to gokcheok(the metal measure, 301.84mm) used now that the length of piers is 46choek(尺), the width of that is 9choek(尺), the length between two piers is 42choek(尺), the length between abutment and pier is 38choek(尺). Also we can see that entirely the length of the bridge is 210choek(尺), width is 40choek(尺).