• Journal of Mechanical Science and Technology
• /
• v.18 no.2
• /
• pp.253-261
• /
• 2004

A simple and effective filtering method to control the member size of an optimized structure is proposed for topology optimization. In the present approach, the original objective sensitivities are replaced with their relative values evaluated within a filtering area. By adjusting the size of the filtering area, the member size of an optimized structure or the level of its topological complexity can be controlled even within a given finite element mesh. In contrast to the checkerboard-free filter, the present filter focuses on high-frequency components of the sensitivities. Since the present filtering method does not add a penalty term to the objective function nor require additional constraints, it is not only efficient but also simple to implement. Mean compliance minimization and eigenfrequency maximization problems are considered to verify the effectiveness of the present approach.

• Proceedings of the IEEK Conference
• /
• 2006.06a
• /
• pp.697-698
• /
• 2006

In this paper, we propose a new scheme to generate multi-view images using a depth-image-based rendering (DIBR) technique. In order to improve the quality of multi-view images at newly exposed areas during mesh-based rendering, we preprocess the depth map using a Gaussian smoothing filter. Previous algorithms apply a smoothing filter to the whole depth map even if the depth map is collapsed. After extracting objects from the depth map, we apply the smoothing filter to their boundaries. Finally, we cannot only maintain the depth quality, but also generate high quality multi-view images. Experimental results show that our proposed algorithm outperforms previous works and supports an efficient depth keying technique.

• Particle and aerosol research
• /
• v.17 no.2
• /
• pp.29-36
• /
• 2021

In this study, the clean air delivery rate (CADR) of ceiling air circulator (CAA) was determined under indoor environmental simulation conditions. An air filter was used to provide air cleaning ability to the CAA. The CADR of filter adapted CAA was evaluated and compared with the value of commercial air purifier. The installation of mesh-shaped filter on the CAA showed particle reduction effect on the particles over 0.4 ㎛ in diameter, but the CADR was up to 0.25 m³/min. When the filter having 99.9% in collection efficiency was installed on the CAA, its CADR was 1.52 m³/min, while the CADR of commercial air purifier was 3.19 m³/min.

• Journal of Environmental Science International
• /
• v.23 no.8
• /
• pp.1409-1418
• /
• 2014

Foundry has an important economic value in the industry. However, the generation of air pollutants like particulate and odor are serious. Due to the unavoidable usage of molding sand, particulate occurs in almost all the processes. That accounts for the majority of respirable dust in the size less than $10{\mu}m$ As well as particulate, over 22 species of odor-causing gases and VOCs including hydrogen sulfide and ammonia are occurred. Therefore, the development of equipment that can simultaneously remove TVOC and particulate is regarded as an essential research. In this study, the spraying absorbent system was connected with the shear bag filter for the purpose to remove TVOC and particulate simultaneously. Maximization of process efficiency for the affective factors like the powder combination and injection method is conducted. The experiment was performed at the de-molding process of one foundry plant. Through these devices, the removal efficiency of more than 95% for TVOC was achieved with the absorbent that composed by 800 mesh Activated carbon (80%) and 300 mesh zeolite (20%). Also, the durability and economic evaluation were assessed. In the result of Durability assessment, the available recovery to maintain the deodorizing effect at 90% was counted to 350 degree.

• Journal of the Korean Society of Tobacco Science
• /
• v.2 no.1
• /
• pp.8-16
• /
• 1980

The cavity of triple filter was filled with the mixture of clinoptilolite and charcoal(1:1, V/V). The particle size of clinoptilolite was 30$\pm$5 A.S.T.M mesh. The reduction effects of the important gaseous components by this mixture were obtained as follows: 1) In comparison with the normal cellulose acetate niter, the contents of nicotine and T.P.M. were reduced about 35% and 22% respectively. 2) Many aliphatic and cyclic compounds were also substantially reduced in an average of 60%. 3) In contrast with the charcoal, the removal efficiency of clinoptilolite was revealed as higher (15-20%) in case of aliphatic compounds than the one (10-15%) of cyclic compounds. The above results showed us that the removal function of gaseous components was quite complementary each other (charcoal and clinoptilolite).

• Journal of KIISE:Computer Systems and Theory
• /
• v.36 no.6
• /
• pp.511-520
• /
• 2009

In this paper, we present a new iso-density surface reconstruction scheme based on a hierarchy on the input volume data and the output mesh data. From the input volume data, we construct a hierarchy of volumes, called a volume pyramid, based on a 3D dilation filter. After constructing the volume pyramid, we extract a coarse base mesh from the coarsest resolution of the pyramid with the Cell-boundary representation scheme. We iteratively fit this mesh to the iso-points extracted from the volume data under O(3)-adjacency constraint. For the surface fitting, the shrinking process and the smoothing process are adopted as in the SWIS (Shrink-wrapped isosurface) algorithm[6], and we subdivide the mesh to be able to reconstruct fine detail of the isosurface. The advantage of our method is that it generates a mesh which can be utilized by several multiresolution algorithms such as compression and progressive transmission.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.60 no.2
• /
• pp.25-36
• /
• 2018

Drip irrigation system is a low energy cost method which can efficiently save and supply water by dropping water slowly on the crop's root zone during crop growth. In the drip irrigation system, disk filters take an important role to physically remove impurity (inorganic and suspended organic) particles present in agricultural water which can cause emitter clogging. For the purpose, both top-and-bottom surfaces of the disk are grooved in micron size flowing from outside to inside. However, many congested flow paths in disk filter media incur higher head loss of inflow water resulting in relatively decreasing velocities depending on operation time than sand and mesh filters. Therefore, it is important to optimize the structure of disk filter in micro irrigation system. The head loss of disk filter media takes also charge of more than 60 % of total head loss in whole disk filter. This study is to find the appropriate cross-sectional shape of the disk groove to minimize the head loss by executing the experiment. The experiment used three disk filters that have similar filter body but have a half-elliptic and two kinds of triangular cross sections. The experimental results showed that the disk filter with half-elliptic cross sections of disk grooves have less head loss than the disk filter with regular triangular one.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.14 no.6
• /
• pp.41-48
• /
• 2015

Stainless steel mesh has been used as a filter in various fields, including domestic, medical, etc. However, the surface before machining may have an adverse effect the product quality and performance because it is not smooth. Especially, adsorbed impurities in the surface result in difficulty in cleaning. Therefore, in this paper, we propose an improved surface quality through electrochemical polishing (ECP). Two electrodes, composed of STS304 (anode) and copper (cathode) underwent machining with two conditions according to polishing time and current density. As the polishing time and current density increase, the surface of curvature decreases, and roughness and material removal rate (MRR) improves. The machined surface roughness and image were obtained through the atomic force microscope (AFM) and stereoscopic microscope. The study also analyzed hydrophilic effect through contact angles. This obtains corrosion resistance, smoothness, hydrophilic property, etc.

• Journal of Korean Society for Atmospheric Environment
• /
• v.31 no.2
• /
• pp.118-130
• /
• 2015

Fine dust containing iron compounds is of current interests in metro subway as well as large scale industries including iron manufacturing and smelting works. This work attempts to find a new design of magnetic filter module for iron dust capture. It simulated the vertical rectangular duct with metal mesh which might promote electric fields in the duct space. A lab test using coal fly ash composed of 8.66% Fe with the most form of $Fe_3O_4$ and $Fe_2O_3$ showed capability of magnetic collection. It showed the capture efficiency with 80~93% for $PM_{2.5}$ depending on magnetic intensity. Ferromagnetic wire mesh contributed up to 50% of collection increment.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.21 no.6
• /
• pp.98-106
• /
• 2022

Among the parts assembled in the gas receiver of a marine engine, the titanium alloy stainless steel (STS 316Ti) wire mesh serving as a filter was broken, and the related part, the turbine fan of the turbocharger, was damaged. In this study, a sample of the grid wire mesh was collected and the cause of breakage was analyzed, and a method of minimizing the dent mark caused by the mold during wire forming, which is one of the most direct causes, was studied. In addition, the optimum mold shape was realized through FEM simulation, and the wire wave molding machine capable of controlling the speed was improved by supplementing the problems of the existing wire wave molding machine, thereby improving durability with minimal dent marks.