• Transactions of the Korean hydrogen and new energy society
• /
• v.9 no.1
• /
• pp.16-24
• /
• 1998

Recently Zr-based $AB_2$ type hydrogen absorbing alloy has received much attention as a negative electrode material for the Ni-MH batteries because of its high capacity. In this study $ZrV_{0.1}Mn_{0.7}Ni_{1.2}$ alloy was chosen and the effects of heat treatment and a partial substitution of the Mo in Mn site on the various electrode properties were investigated. The alloys was prepared by arc melting (as-cast sample). Some of them were heat treated at $1,100^{\circ}C$ for 4 hours. After this they were differentiated by the different cooling rates of slow cooling and quenching. Various electrode characteristics such as activation process, high rate dischargeability and self discharge characteristic were investigated with the three types of electrodes. It was found that heat treated alloys resulted in an increase in plateau flatness of P-C isotherms however both discharge capacity and high rate capability were decreased. And the partial substitution of Mo for Mn in $ZrV_{0.1}Mn_{0.7}Ni_{1.2}$ alloy improved the self-discharge characteristic without the loss of discharge capacity (300mAh/g).

• Journal of Radiation Protection and Research
• /
• v.38 no.4
• /
• pp.228-233
• /
• 2013

It has been continuously generated the requirement for the replacement of the main components such as a steam generator due to the deterioration of the nuclear power plant all around the world. Also, a large amount of radioactive metal was generated during the decommissioning in a short period. It is required to make an accurate measurement of the residual radioactivity for recycling the metal waste for releasing from regulatory control. In planning the measurement procedures, the influence of geometry, self-absorption, density and other relevant factors on the representativeness of the measurements should be considered for the decommissioning metal waste. In this study, the method for measurement procedures, the source term evaluation, the ways to secure representative samples, the measurement device for wide area and the self-absorption correction factors for different density were evaluated. The metal samples for measurement were prepared for securing the simple geometry and representative by melting process. The developed correction method for measuring the radioactivity a variety density of metal waste could improve the reliability of the evaluation results for clearance.

• Polymer(Korea)
• /
• v.35 no.1
• /
• pp.30-34
• /
• 2011

In this study, the effects of the electron beam irradiation on the thermal behavior and the abrasion properties of the glass fiber reinforced nylon 12 was investigated. The electron beam irradiation was carried out over a range of irradiation dose from 100 to 600 kGy with additive crosslinking agents such as triallyl cyanurate (TAC), triallyl isocyanurate (TAIC) and trimethylolpropane trimethacrylate (TMPTMA) for enhancing the crosslinking effects. The gel contents were increased dramatically above 200 kGy. It was verified that the degree of crosslinking depends on the radiation dose. The decreases of the melting temperature and the area of endothermic peak were observed as increasing the absorbed dose in the results of DSC analysis. The enhanced thermal stability was confirmed by the increases of decomposition temperature by electron beam irradiation. Furthermore, the negative deviations of the abrasion loss and the abrasion coefficients confirmed the improvement of the abrasion properties of irradiated nylon 12, as evidenced by SEM observation on the abrasion surfaces. The addition of the crosslinking agents to nylon 12 during effectively improved the thermal behavior and the abrasion properties of nylon 12 by the electron beam irradiation.

• Solar Energy
• /
• v.11 no.2
• /
• pp.41-50
• /
• 1991

Heat transfer phenomena and temperature characteristics in heat storage and release process in the heat storage system using PCM(Phase Change material) were studied experimentally. The melting points of Octacosane paraffin($C_{28}H_{58}$) and sodium pyrophosphate decahydrate ($Na_4P_2O_7{\cdot}10H_2O$) used for phase change materials are $62^{\circ}C$ and $79^{\circ}C$ respectively. Experiments were performed in order to investigate temperature distributions, the heat storage quantity and the release quantity on octacosane paraffin and sodium pyrophosphate decahydrate for heat storage and release in the heat storage system. Furthermore the comparison of these characteristics between paraffin and $Na_4P_2O_7{\cdot}10H_2O$ were evaluated. In case of the paraffin, temperature slowly increased at early heat storage process by natural convection, while temperature of $Na_4P_2O_7{\cdot}10H_2O$ rapidly increased the dominant role played by conduction at early heat storage processing Also, during the heat storage and release process in case of the paraffin, it was observed that the variation of temperature of the neighborhood of wall and center in the top and bottom of the tube exhibited a great difference, however in $Na_4P_2O_7{\cdot}10H_2O$, it was observed that the variation of temperature exhibited a little difference. And heat storage quantity of each PCM of identity mass in heat storage process was shown that $Na_4P_2O_7{\cdot}10H_2O$ exhibited more by 16 percents than paraffin.

• Korean Journal of Materials Research
• /
• v.11 no.5
• /
• pp.345-353
• /
• 2001

The present study was carried out to investigate the effect of zirconium addition to $Al_3$Nb intermetallic on the crystal structural modification and microstructural characterization of $Al_3$Nb intermetallic. Elemental Al, Nb, Zr powders and arc melted $Al_3$Nb and $Al_3$Zr intermetallic mixed powders were used as starting materials. MA was carried out in an attritor rotated with 300 rpm for 20 hours. The behavior of MA between two starting materials was some-what different in which the value of internal strain of the elemental powders was higher than that of the intermetallic powder. The intermetallic powder was much more disintegrated during the MA processing. In the case of the elemental powders, AlNb$_2$ phase were transformed to Al(Nb.Zr)$_2$ as a result of ternary addition of Zr element. With the successive heat treatment at 873K for 2 hours, the Al(Nb.Zr)$_2$ phase was transformed to more stable $Al_3$(Nb.Zr) phase. This transformation was clearly confirmed by the identification of X-ray peak position shift. On the other hand, in the carte of the intermetallic powder, there was no evidence of phase transformation to other ternary intermetallic compounds or amorphous phases, even in the case of additional heat treatment. However, nano-sized intermetallic with $Al_3$Nb and $Al_3$Zr were just well distributed instead of phase transformation.

• The Korean Journal of Food And Nutrition
• /
• v.16 no.4
• /
• pp.296-302
• /
• 2003

First. the purification and analysis of alliin in garlic from different origins by alliin-HPLC determination method were studied. Allinase in garlic was inactivated by heating in boiling water followed by extraction of alliin in garlic with 80% methanol. To remove free amino acids and alliin homologs in garlic, garlic extract was separated by cation exchange column which was packed with amberlite CG-120 resin using 40L d-water as eluent. Alliin in garlic extract was crystallized in a mixture of acetone (50$^{\circ}C$)：H$_2$O：acetic acid=70:29:1 and then recrystallized in a mixture of acetone (50$^{\circ}C$)：H$_2$O：acetic acid=75:24:1. Obtained alliin was identified by melting point. TLC, microscope observation and mass spectrometry. High performance liquid chromatography (HPLC) following pre-column derivatization of cystein derivatives with o-phthaldialdehyde/2-mercaptoethanol has succeessfully been applied to the analysis of various garlics. Each alliic of standard solution and garlic extract was derivatized to isoindole derivative by o-phthaldialdehyde /2-mercaptoethanol and then analyzed by HPLC. Six point calibration was done by using alliin peak area. Lineality was observed at 0 ∼ 1.0mg/ml of alliin concentration. Weighted regression line function was Y=6254X - 256077. By this function, alliin contents in various garlics were 0.34 ∼ 0.73% fresh weight. Second study was designed to evaluate the effects of garlic extracts of various concentrations on the growth of various pathogenes (Eubacterium limonsum, Bacteroides fragilis, Salmonella typhimurium, Salmonella typhi, Shigella sonnei, Kiebsiella pneumoniae, Enterobacter cloacae, Pserdomonas aeruginosa, Escherichia coli). For antimicrobial effects against microorganism, totally minimal inhibition concentrations (MIC) of alliin were from 5,000 to 20,000ppm. MIC of ethanol extract were 1,250 to 10,000ppm.

• Food Science of Animal Resources
• /
• v.36 no.5
• /
• pp.665-670
• /
• 2016

The objectives of this study were conducted to characterize pepsin-soluble collagen (PSC) extracted from bones (PSC-B), skins (PSC-S), and tendons (PSC-T) of duck feet and to determine their thermal and structural properties, for better practical application of each part of duck feet as a novel source for collagen. PSC was extracted from each part of duck feet by using 0.5 M acetic acid containing 5% (w/w) pepsin. Electrophoretic patterns showed that the ratio between α₁ and α₂ chains, which are subunit polypeptides forming collagen triple helix, was approximately 1:1 in all PSCs of duck feet. PSC-B had slightly higher molecular weights for α₁ and α₂ chains than PSC-S and PSC-T. From the results of differential scanning calorimetry (DSC), higher onset (beginning point of melting) and peak temperatures (maximum point of curve) were found at PSC-B compared to PSC-S and PSC-T (p<0.05). Fourier transform infrared spectroscopy (FT-IR) presented that PSC-S and PSC-T had similar intermolecular structures and chemical bonds, whereas PSC-B exhibited slight difference in amide A region. Irregular dense sheet-like films linked by random-coiled filaments were observed similarly. Our findings indicate that PSCs of duck feet might be characterized similarly as a mixture of collagen type I and II and suggest that duck feet could be used for collagen extraction without deboning and/or separation processes.

• Journal of Conservation Science
• /
• v.32 no.4
• /
• pp.549-560
• /
• 2016

The purpose of this study is to identify the material characteristics of blackwares excavated from the Bonggok kiln site in Jinan-gun, Jeollabuk-do Province, South Korea, by scientific analyses and a reproduction experiment. Scientific analyses were conducted to determine the physical properties, chemical composition and for microscopic observation of blackwares. A reproduction experiment was also conducted by producing ceramic samples with black glaze, red ocher and limestone, and then cross sections of the samples were observed. The analysis results showed that all the excavated blackwares have similar properties such as chromaticity, specific gravity, absorption factor and porosity, but there is a difference depending on the crystallization of the ceramics. Thermal analysis showed that the exothermic peak was observed at about $1200^{\circ}C$, and crystal structure analysis indicated the presence of mullite. Hence, it can be concluded that the firing temperature of the excavated blackwares was around $1100-1200^{\circ}C$. Moreover, the glaze present on these blackwares has about 22% higher $Fe_2O_3$ content than those excavated from other places; however, the former has lower CaO content. For the reproduction experiment, samples were made using limestone as a flux and red ocher as a glaze. The results show that the cross section of the glaze layer of the reproduced sample have iron crystals with dendritic structures, similar to those present in the excavated black-wares. It is assumed that such iron crystals were formed during the process of melting and solidification of the iron oxide present in the blackwares.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.20 no.1
• /
• pp.43-52
• /
• 2010

Glass was fabricated by using refused coal ore obtained from Dogye coal mine in Samchuk. We additionally used soda ash and calcium carbonate as raw materials to make a glass with the chemical composition of soda-lime glass. And the properties of glass were measured when limestone was used as natural raw materials instead of calcium carbonate as chemical raw materials. Transparent glass was fabricated by melting raw materials at $1550^{\circ}C$ for 1 hr in an electrical furnace. The various kinds of glass samples were fabricated according to the kinds of refused coal ore and glass cullet. The optical properties of transmittance and color chromaticity were measured by UV/VIS/NIR spectrometer and the thermal properties of thermal expansion coefficient and softening point were measured. Transparent glass with the transmittance of over 70% in visible range was fabricated by using normal refused coal ore and black colored glass with the transmittance of 0~35% was fabricated by using shel1 type refused coal ore. Therefore, it is concluded that refused coal ore can be used for raw materials to manufacture secondary glass products such as a glass tile and foamed glass panel for construction material.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.28 no.3
• /
• pp.130-134
• /
• 2018

In the past few years, various solder compositions have been a representative material to electronic packages and surface mount technology industries as a replacement of Pb-base solder alloy. Therefore, extensive studies on process and/or reliability related with the low Ag composition have been reported because of recent rapid rise in Ag price. In this study, Sn-3.0Ag-0.5Cu, Sn-0.7Cu and Sn-0.3Ag-0.5Cu solder bar samples were fabricated by melting of Sn, Ag and Cu metal powders. Crystal structure and element concentration were analyzed by XRD, XRF, optical microscope, FE-SEM and EDS. The fabricated solder samples were composed of ${\beta}-Sn$, ${\varepsilon}-Ag_3Sn$ and ${\eta}-Cu_6Sn_5$ phases.