• 한국디자인학회:학술대회논문집
• /
• 한국디자인학회 2002년도 봄 학술발표회 논문집
• /
• pp.22-23
• /
• 2002

• 디자인학연구
• /
• 제15권3호
• /
• pp.63-72
• /
• 2002

우리 일상생활에서 밀접하게 접하고 사용하고 있는 샤프펜슬에 사용편의성(쓰기 편한 정도)을 1.사용 전 보았을 때 예전 경험치로 직감적으로 느끼는 감, 2.직접 잡았을 때 느낌(착용감), 3.직접 종이 위에 쓰면서 느끼는 느낌 (필기감), 이 세 가지 주요평가항목으로 설정한 후 36개의 대표샘플을 가지고 실증적 실험방법으로 서로의 관계 및 직접 영향을 미치는 항목을 구체적으로 밝혔다. 본 연구에서는 사용편의성과 사용 전 보았을 때 예전 경험치로 직감적으로 느끼는 감의 항목에서는 서로는 높은 상관관계는 없었다. 이는 경험치에서 얻은 기대치가 실제로 사용에서는 기대치에 미치지 못하였기 때문이라고 판단한다. 사용편의성과 착용감, 필기감은 높은 상관관계를 가지고있었다. 이는 사용편의성에 있어 착용감과 필기감은 서로 밀접한 관계이기 때문이라고 판단한다. 사용편의성이 좋은 샤프펜슬은 구조적으로 전체길이가 길며(169mm), 굵기는 보통(8.5mm), 무게는 약간 무거운(21.4g), 중심은 야간 아래쪽인(60mm)에 위치하며, 단면형상은 정원이 아닌 변형형상이며, 손가락 접지부의 표면처리는 가로 홈이 나있는 것이고, 몸통은 광택이 있는 것으로 나타났다.

• 대한기계학회논문집A
• /
• 제24권4호
• /
• pp.1024-1031
• /
• 2000

The plate waves propagating in thin plates have dispersive nature showing the dependence of velocities on the frequency. Wavelet transform (WT) using Gabor function can be used to analyze the dispersive waves in the time-frequency domain, and then to find the arrival time of the waves propagating in the plate. Plate waves in the aluminum plate of 3 mm thickness were identified and generated by pencil lead breaks and the lowest order symmetric ($S_o$) and antisymmetric ($A_o$) modes were analyzed by the WT method. The measured group velocities agreed very well with theoretical predictions in the frequency range of 50-400 kHz. The pencil breaks were also used to simulate acoustic emission sources in the plate, and the source location algorithm using the wavelet transform of dispersive plate waves was found to give accurate results.

• Journal of Mechanical Science and Technology
• /
• 제19권spc1호
• /
• pp.292-304
• /
• 2005

In this paper we present the linearized equations of motion for a bicycle as a benchmark. The results obtained by pencil-and-paper and two programs are compared. The bicycle model we consider here consists of four rigid bodies, viz. a rear frame, a front frame being the front fork and handlebar assembly, a rear wheel and a front wheel, which are connected by revolute joints. The contact between the knife-edge wheels and the flat level surface is modelled by holonomic constraints in the normal direction and by non-holonomic constraints in the longitudinal and lateral direction. The rider is rigidly attached to the rear frame with hands free from the handlebar. This system has three degrees of freedom, the roll, the steer, and the forward speed. For the benchmark we consider the linearized equations for small perturbations of the upright steady forward motion. The entries of the matrices of these equations form the basis for comparison. Three diffrent kinds of methods to obtain the results are compared : pencil-and-paper, the numeric multibody dynamics program SPACAR, and the symbolic software system Auto Sim. Because the results of the three methods are the same within the machine round-off error, we assume that the results are correct and can be used as a bicycle dynamics benchmark.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1998년도 제28회 추계학술대회
• /
• pp.278-284
• /
• 1998

In order to measure the real contact force between head and disk on hard disk drive quantitatively, many technique of measurement have been developed. Acoustic Emission Sensor can be used for detect elastic energy of head/disk contact as arms value. In this study using pencil breaking test is proposed for finding contact force using transfer function between calibrated force and real contact force. And real AE data of subambient and tripad slider shows bending and torsional mode and their energy are dominant in hard disk and head contact.

• Journal of Industrial and Engineering Chemistry
• /
• 제68권
• /
• pp.209-219
• /
• 2018

Colloidally stable organic-inorganic (O-I) hybrid nanoparticles could be prepared using an alkoxysilanefunctionalized amphiphilic polymer (AFAP) precursor. O-I hybrid sols could maintain colloidal stability for six months even at 45% solid content and be coated onto glass as well as PET film to form transparent O-I hybrid films. The formation of O-I hybrid nanoparticles dispersed in cured coating films could be confirmed using scanning electron microscopy. The cured coating film showed 3H and 5H pencil hardness on PET and glass, respectively. Nanoindentation measurements also showed that their modulus and hardness was varied with the type of AFAP used in its preparation.

• 대한기계학회논문집A
• /
• 제24권12호
• /
• pp.2891-2898
• /
• 2000

The objective of this paper is to develop a fiber-optic acoustic emission(AE) sensor applicable to on-line monitoring systems which is suitable for long-distance signal transmission. An AE sensor was developed by use of a fiber-optic cantilever and an extrinsic Fabry-Perot interferometer(EEPI). The efficiency of signal processing was improved by driving the high frequency AE signals into the low frequency ones. In order to verify the developed sensor, the tensile and the pencil lead fracture(PLF) tests were performed including the experiment showing the Kaiser effect. Form tests, AE signals were successfully detected in the elastic-plastic deformation range, especially higher signals at the crack propagation. The developed sensor was expected to be used for an on-line monitoring of crack propagation in mechanical system.

• 공업화학
• /
• 제30권3호
• /
• pp.358-364
• /
• 2019

반사 방지(anti-reflective; AR) 코팅막의 광학 특성 및 내오염성을 향상하기 위하여 tetraethylorthosilicate (TEOS)/염기 및 methyltrimethoxysilane (MTMS)/산 혼성 용액의 혼합비를 변화시키며 다양한 AR 코팅막을 제조하였다. 제조된 AR 코팅막은 UV-Vis, 접촉각 측정기, AFM, FT-IR 및 연필 경도 시험을 통해 특성을 분석하였다. MTMS/산 용액의 함량이 10 wt%인 혼성 용액으로 제조한 AR 코팅막에서 유리 기판은 매우 우수한 광학 특성(97.2%의 투과율), 우수한 내오염성($121^{\circ}$의 물 접촉각 및 $90^{\circ}$의 $CH_2I_2$ 접촉각), 중간 정도의 기계적 강도(4 H의 연필 경도)를 나타내었다. 특히 우수한 내오염성은 기판의 표면 위에서 혼성 용액 내 소량의 MTMS/산 용액으로부터 유래된 메틸기($-CH_3$)의 고른 분산에 기인한 것으로 고려되었다. 연필 경도 시험 결과로부터, AR 코팅막의 기계적 강도는 MTMS/산 용액의 함량이 증가할수록 향상되는 것으로 나타났다.

• 대한기계학회논문집A
• /
• 제22권3호
• /
• pp.688-694
• /
• 1998

The ability to locate the defects in materials is one of the major attrations of the acoustic emission(AE) technique. The most conventional method for planar AE source localization is to place three or more AE sensors on the plate and to determine the source position by measuring the differences in the arrival times of the AE wave at the sensors, which is called as triangulation method. But this method can not be applied in the material of which elastic wave propagtion velocity is not known. In this paper, we propose two methods, vector method and error minimization method, for AE source location on the material with unknown AE wave velocity. In this method, it is not needed to know the propagation velocity previously, that is, we can apply this method to arbitrary material of which properties are not known exactly. Also, in this paper, the robustness to the error in the measurement of time differences are discussed for both methods. Finally, in order to evaluate the actual performances, experiments using a pencil lead break as the AE source were carried out on the aluminum plate.

• 한국세라믹학회지
• /
• 제41권5호
• /
• pp.349-352
• /
• 2004

Organic-inorganic hybrid sol based on ZrO$_2$-SiO$_2$ system was prepared by sol-gel process. Firstly, ZrO$_2$ non-aqueous precursor sol was synthesized and then organosilane compounds which include epoxy silane (GPTS; 3-g1ycidoxypropyl tri-methoxysilane) and acryl silane (ACS; (3-(tri-methoxysilyl)propylmethacrylate)) were added to ZrO$_2$precursor sol for hybridization. Finally, com-mercial silica sol was added to improve the mechanical properties. Synthesized organic-inorganic Zr-hybrid sol was coated on polycarbonate substrate for enhancing it’s mechanical properties, especially hardness. Vicker’s hardness of polycarbonate sub strate was increased from 13.6 to 17.8 MPa and its pencil hardness was increased from 2 to 7 H, respectively, after coating and drying at 10$0^{\circ}C$ for 30 min.