• Journal of Biosystems Engineering
• /
• v.37 no.3
• /
• pp.184-191
• /
• 2012

Purpose: This study was conducted to investigate the storage and quality characteristics of brown rice under the low temperature warehouse conditions using ambient cold air in the winter. Methods: This new technique maintains rough rice warehouse temperature below $15^{\circ}C$ without cooling operation until the end of May. Four hundred tons of rough rice were stored in the low temperature grain warehouse, and were aerated from the top to the bottom using ambient cold air in February. The quality of rough rice was evaluated from February through October. Results: The results were as followings. Moisture contents of rough rice in the low temperature storage had decreased less than the ordinary temperature storage. Cracked rate of brown rice in the ordinary temperature storage and low temperature storage increased by 4~10.8% and 1.6~7.2%, respectively. The germination rate of rough rice under the ordinary and the low temperature warehouse decreased by 15.0~25.0% and 1.7~8.0%, respectively. The acid value of brown rice under the ordinary and the low temperature warehouse increased by 3.67~6.72 KOH mg/100g and 3.08~4.08 KOH mg/100g, respectively. Conclusions: The result indicates that low temperature storage using ambient winter air showed better maintaining germination of rice, less change of physiological activities and cracked kernel, and better maintaining of rice quality, comparing the ordinary temperature storage.

• Journal of Biosystems Engineering
• /
• v.35 no.4
• /
• pp.244-249
• /
• 2010

This study was conducted to define the optimal Lycium chinense miller washing method for developing the Lycium chinense cleaner and we analyzed the Lycium chinense miller washing characteristics for removing pesticides and microorganism according to washing methods; habitual washing method, air bubble washing method and nozzle spray washing method. The results were summarized as follows; 1. In case of measuring physical properties according to the varieties, maximum yield strength of Hokwang was 2.562 kgf, minimum yield strength of Hokwang was 0.269 kgf and average yield strength was about 1 kgf. 2. In case of measuring change of bacteria according to washing methods, the number of bacteria of non-washing method was more than the number of bacteria of habitual washing method or mechanical washing method and the number of nozzle spray washing method was least. 3. Ahjoksiseuteurobin of 0.218 ppm was detected in the untreated sample, 0.051 ppm was detected in the habitual washing method, 0.047 ppm was detected in the air bubble washing method and 0.034 ppm was detected in nozzle spray washing method. Every amount detected were less than 2 ppm that is reference value and the detected amount was least in case of nozzle spay cleaning method. Cypermethrin of 0.772 ppm was detected in the non-cleaned sample, 0.089ppm was detected in habitual washing method, 0.26 ppm was detected in the air bubble washing method and 0.292 ppm was detected in the nozzle spray washing method. Every detected amount of Cypermethrin were less than 5 ppm that is reference value and the detected amount was least in case of habitual washing method.

• Journal of the Korean Society for information Management
• /
• v.35 no.3
• /
• pp.147-164
• /
• 2018

This study defined the name of records producing institution as the unique preferred form of access point which has same identification and same entity by using Standard Administration Code, and also described the name of records producing institution which has various name form as formal-name form of access point, which has same identification and same entity. This study make us be able to identify and access to all of the records that institution, has same identification and same entity, has produced. And the mechanic, I designed by ontology would make reinforce 'the principle of provenance' and 'respect for orignal order' and make user satisfy in useability of archives and expanded retrieval results.

• Journal of Korea Technology Innovation Society
• /
• v.17 no.1
• /
• pp.174-194
• /
• 2014

Collaborative technology development is now one of the most significant modes of activity in the global scientific community. However, the international cooperation of science and technology simultaneously provides opportunities and challenges, and the results of global R&D collaboration can be positive or negative as the cooperation conditions of the parties may be different according to the types or characteristics of the participants and the pattern, purpose, and motivation of cooperation. In order to minimize the risk and improve the performance of cooperation, more comprehensive as well as micro-level research is needed. This study investigates a case of successful collaborative R&D conducted by several firms, universities, and public research organizations in both Korea and the U.S.A. The aim of this study is to identify the factors of successful R&D collaboration.

• Current Research on Agriculture and Life Sciences
• /
• v.15
• /
• pp.115-122
• /
• 1997

Grafting is an important skill for the stable supply and production of high quality. However, the shortage of skillful labor has become great difficulty for a mass production of grafting-seedling. In this study, a suitable mechanism for a grafting machine was developed. The following summarize the results of this study: 1. An insertion method was selected for mechanism of the grafting machine without bonding agent, clip, pin. This insertion-grafting method can be applicable to general vegetables and a mass production system. In addition to, this method is suitable for developing the grafting mechanism. 2. Growing point was removed while remaining both cotyledons on rootstock. The productivity of this system was five fold greater than the one of an experienced labor. 3. The rootstock processing was placed on left and scion processing unit was placed on right of the system, then processed rootstock and scion graft by rotating $180^{\circ}$. 4. The efficiency tests on mechanical grafting rate showed 98%.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.3
• /
• pp.1600-1604
• /
• 2015

As modern houses are constructed with high-density and high-insulation, there is benefit to reduce energy consumption, but there are many side effects raised from polluted air. To solve the problem, a ventilation system is used to improve a indoor air quality. In this research, we experimentally estimate ventilation performance of HRV(heat recovery ventilator) with heat-pipe according to working fluid filling quantity and ventilation. Heat-pipe used in this study was designated separately to be applied to a ventilation system. The working fluid was R22, which was filled from 40 to 55 (%vol.) by 5(%vol.). Ventilation based on the front velocity was measured from 0.3 m/s to 1.5 m/s by 0.3 m/s intervals. Refrigerant filling quantity with the highest efficiency was found to depend on the ventilation. From this study the optimal refrigerant filling quantity in accordance with the ventilation of the detachable heat pipes was found experimentally.

• Journal of Digital Convergence
• /
• v.18 no.11
• /
• pp.187-194
• /
• 2020

This study present to Framework & R&D direction of the 3d printing Integrated Control & Monitoring System. To ensure this purpose, we developed integrated 3d printing control system Framework for DED & PBF and we introduce 4 monitoring system include photo diode, gas flow, acoustic and spectrometer sensors. For this study, we utilize metal 3d printing system from Conception., OKE Tech and DE&T who are still developing Metal 3D Printing Technology since 2017. In the result, we represent the latest 3D Printing Control and Monitoring System for the next 3D Printing researcher and we hope this study will be used as a basic reference and data for Cooperation between mechanic, electronic and material fields.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.27 no.5
• /
• pp.459-467
• /
• 2014

ILM(Incremental Launching Method) bridges pass both the middle of spans and supports during launching. The launching noses are used to minimize the maximum positive moments and negative moments of the superstructure occurring during launching for ILM bridges. In this study, the simplified analysis formula considering diaphragm to calculate the bending moment that occurs during launching is induced and analyzes the optimum design conditions considering diaphragm. The accuracy of the proposed simplified analysis formular compared to the MIDAS Civil has an error of less than 5%. There is a difference up to 13% in the moment between the cases when the diaphragm is considered and is not. In addition, the criteria for deciding the unit weight of equivalent cross section and average stiffness value of equivalent cross section that can be applied to the simplified analysis formula is proposed. In this study, an effective way to optimize the launching nose is proposed that the optimum design is taken in the condition of minimizing the negative moment because of the mechanic characteristic of ILM bridges.

• The Journal of Korean Association of Computer Education
• /
• v.8 no.3
• /
• pp.29-42
• /
• 2005

In this knowledge information society, it cannot be too much to accentuate the necessity and importance of computer education. However, the current computer education in elementary school only focuses on computer application and utilization. It is not satisfactory to the needs of knowledge information society to improve mechanic office operation and/or to provide simple utilization of educational software through learning the application software functions. Therefore, based on creative and logical thought, it is necessary at this era to prepare computer education as the essence of science to create new values and to embody knowledge by understanding social and cultural environment of knowledge information society that is continuously in change and development. Accordingly, this study presents the necessity of change based on problems of computer education, and investigates field teacher's opinion on the direction of change in elementary computer curriculum in this knowledge information society. Also, this study presents a computer education curriculum for elementary school students by focusing on a comparison between our current elementary computer curriculum and that of North Carolina and of California in the United States.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.6
• /
• pp.683-693
• /
• 2010

In this paper, we propose a new parallel mechanism for the legs of biped robots and the control of the robot's locomotion. A leg consists of two 3-DOF parallel platforms linked serially: one is an orientation platform for a thigh and the other is the 3-DOF asymmetric parallel platform for the shank. The desired locomotion trajectory is generated on the basis of the Gravity-Compensated Inverted Pendulum Mode (GCIPM) in the sagittal direction and the Linear Inverted Pendulum Mode (LIPM) in the lateral direction, respectively. In order to simulate the ground reaction force, a 6-DOF elastic pad model is used underneath each of the soles. The performance and effectiveness of the proposed parallel mechanism and locomotion control are shown by the results of computer simulations of a 12-DOF parallel biped robot using $SimMechanics^{(R)}$.