• 한국통신학회논문지
• /
• 제22권5호
• /
• pp.915-927
• /
• 1997

In this paper, we propose an error concealment technique using directional interpolation in block-based image compression. In the proposed method the edge direction is determined by finding the maximum correlation coefficients of boundary pixels of blocks neighboring the errored block in spatial domain. Then the errored block is interpolated linearly or bilinearly along the determined edge direction. The proposed method can conceal the block error, the macro block error, and the slice error adaptively. Also, the parameters for the directional interpolation are represented by closed forms. When applied to compressed images, the proposed method shows superior subjective and objective quality to conventional error concealment methods.

• Nuclear Engineering and Technology
• /
• 제31권3호
• /
• pp.303-313
• /
• 1999

Various interpolation methods have been compared for reconstruction of LMR pin power distributions in hexagonal geometry. Interpolation functions are derived for several combinations of nodal quantities and various sets of basis functions, and tested against fine mesh calculations. The test results indicate that the interpolation functions based on the sixth degree polynomial are quite accurate, yielding maximum interpolation errors in power densities less than 0.5%, and maximum reconstruction errors less than 2% for driver assemblies and less than 4% for blanket assemblies. The main contribution to the total reconstruction error is made tv the nodal solution errors and the comer point flux errors. For the polynomial interpolations, the basis monomial set needs to be selected such that the highest powers of x and y are as close as possible. It is also found that polynomials higher than the seventh degree are not adequate because of the oscillatory behavior.

• 대한기계학회논문집A
• /
• 제29권2호
• /
• pp.277-283
• /
• 2005

Kriging model is widely used as design analysis and computer experiment (DACE) model in the field of engineering design to accomplish computationally feasible design optimization. In general, kriging model has been applied to many engineering applications as an interpolation model because it is usually constructed from deterministic simulation responses. However, when the responses include not only global nonlinearity but also numerical error, it is not suitable to use Kriging model that can distort global behavior. In this research, generalized kriging model that can represent both interpolation and regression is proposed. The performances of generalized kriging model are compared with those of interpolating kriging model for numerical function with error of normal distribution type and trigonometric function type. As an application of the proposed approach, the response of a simple dynamic model with numerical integration error is predicted based on sampling data. It is verified that the generalized kriging model can predict a noisy response without distortion of its global behavior. In addition, the influences of maximum likelihood estimation to prediction performance are discussed for the dynamic model.

• 대한수학회논문집
• /
• 제17권4호
• /
• pp.741-754
• /
• 2002

In this paper we present an error bound for cubic spline approximation of conic section curve. We compare it to the error bound proposed by Floater [1]. The error estimating function proposed in this paper is sharper than Floater's at the mid-point of parameter, which means the overall error bound is sharper than Floater's if the estimating function has the maximum at the midpoint.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.492-495
• /
• 2001

In order to utilize a parallel machine tool for CAM system, the development of adequate interpolator is necessary. This paper presents a quintic B-spline interpolator with algorithm of limiting maximum interpolation error. The favored property of near arc-length parametrization in the curve representation is used in the implementation of the reference command generation. Then, this interpolator is applied to cubic parallel manipulator to show its validity.

• 한국항해항만학회지
• /
• 제36권5호
• /
• pp.371-378
• /
• 2012

본 논문에서는 OQPSK(Offset Quadrature Phase Shift Keying) 변복조를 사용하는 수중음향통신에서 시간동기회복을 위해 기존의 Gardner TED(Timing Error Detector)에 Parabolic Peak Interpolation 을 사용하는 Peak Detector를 첨가하여 위상 수렴속도를 상승시켜 송신 데이터양의 감소를 도모하였다. Parabolic Peak Interpolation을 이용하여 지속적으로 국소 최대 또는 최소의 근사치로 이동한 후 Gardner TED를 적용하기 때문에 시간동기화 안정화를 속도를 빨리함으로써 Preamble 구간의 데이터양을 절반으로 줄일 수 있고 또한 Preamble 구간에서도 위상 수렴을 하지 못하는 임계치에서 제안한 방법을 시뮬레이션한 결과 임계점에서 BER(Bit Error Rate)이 약 23%정도 성능이 개선되는 것을 확인할 수 있었다. 또한 실제 동해에서 수집한 데이터를 사용하여 기존의 Gardner TED만 사용하는 방법과 성능 비교 결과 송수신기 사이의 거리가 3 km 이었을 때 제안한 방법을 적용한 경우 기존의 방법에 비해 Converge speed가 1.4배 이상 상승하는 것을 확인할 수 있었고, BER측면에서도 약 20%정도 상승하는 것을 확인할 수 있었다.

• International Journal of Precision Engineering and Manufacturing
• /
• 제7권4호
• /
• pp.51-56
• /
• 2006

This paper proposes a control algorithm, which is verified experimentally, for aspherical surface grinding and polishing. The algorithm provides simultaneous control of the position and interpolation of an aspheric curve. The nonlinear formula for the tool position was derived from the aspheric equation and the shape of the tool. The function was partitioned at specific intervals and the control parameters were calculated at each control section. The position, acceleration, and velocity at each interval were updated during the process. A position error feedback was introduced using a rotary encoder. The feedback algorithm corrected the position error by increasing or decreasing the feed speed. In the experimental verification, a two-axis machine was controlled to track an aspherical surface using the proposed algorithm. The effects of the control and process parameters were monitored. The results demonstrated that the maximum tracking error with tuned parameters was at the submicron level for concave and convex surfaces.

• Journal of Advanced Marine Engineering and Technology
• /
• 제20권4호
• /
• pp.90-100
• /
• 1996

To maintain high spacial accuracy and rapid CPU time in interpolating data from grid to random position or inversely in PIV, proposed many technuques are compared and discussed mainly in terms of interpolating error and computing time. And artificial PIV atmosphere data is furnished by CFD result. First, for interpolation from grid to random position, multiquadric method gives the highest accuracy with the longest CPU time and Taylor series expansion methods give reasonable accuracy with less calculating load. Secondly, the sub-pixel resolution analysis in estimating the coordinates of the maximum correlation coefficients essential in the grey level correlation PIV reveal that 8-neighbours 2nd-order least square interpolation gives utmost accuracy in terms of the real flow conditions.

• Journal of Advanced Marine Engineering and Technology
• /
• 제20권4호
• /
• pp.412-412
• /
• 1996

To maintain high spacial accuracy and rapid CPU time in interpolating data from grid to random position or inversely in PIV, proposed many technuques are compared and discussed mainly in terms of interpolating error and computing time. And artificial PIV atmosphere data is furnished by CFD result. First, for interpolation from grid to random position, multiquadric method gives the highest accuracy with the longest CPU time and Taylor series expansion methods give reasonable accuracy with less calculating load. Secondly, the sub-pixel resolution analysis in estimating the coordinates of the maximum correlation coefficients essential in the grey level correlation PIV reveal that 8-neighbours 2nd-order least square interpolation gives utmost accuracy in terms of the real flow conditions.

• 한국정밀공학회지
• /
• 제14권11호
• /
• pp.77-83
• /
• 1997

This work is concerned with the algorithm of generating a new circular are interpolation. This research presents a new biarc curve fitting that is a circular interpolation method based on a triarc curve fitting. The triarc method, where a segment span is composed of three circular arcs, using maximum error estimation has the advantage of generating arc splines easily to a given tolerance. The new biarc method is called when the adjacent radii are the same in the same in the triarc method. In generating the machining data for various cam curves in CNC machining with the biarc method and the new biarc method, the latter accomp- lished faster NC-code generation, shorter NC-code block formation and machined the same cam profile more efficiently.